Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for W&T WuTooth 97100
Summary of Contents for W&T WuTooth 97100
- Page 1 Manual WuTooth Bluetooth W&T Modell 97100, 97101 Release 1.02, Nov 2012...
- Page 2 W&T © 11/2012 by Wiesemann & Theis GmbH Subject to errors and modifications: Since we can make mistakes, none of our statements should be used without verification. Please inform us of all errors or misunderstandings which you become aware of so that we can recognize and eliminate them as quickly as possible.
-
Page 3: Introduction
W&T Introduction The W&T WuTooth allows you to measure air temperature and relative humidity, log the information and use your Android smartphone to access it via Bluetooth. -
Page 4: Table Of Contents
W&T Content Introduction ................. 3 1 Commissioning ..............5 1.1 Powering with AA / rechargeable battery ...... 5 1.2 Powering from the USB interface ........6 2 Connecting the WuTooth ........... 7 2.1 Pairing ..............7 3 WuTooth App ..............10 4 Indicators ................ -
Page 5: Commissioning
W&T 1 Commissioning The W&T WuTooth can be powered by a AA battery (also rechargeable) or a USB interface. 1.1 Powering with AA / rechargeable battery The unit is supplied with a battery already installed and ready to use. To change the battery proceed as follows: Open the housing by turning the lower latch and remove the board. -
Page 6: Powering From The Usb Interface
W&T 1.2 Powering from the USB interface Connect the Micro-USB cable (available as an accessory) to the WuTooth by connecting the plug to the WuTooth through the opening in the lower cover. The device can now be powered by a USB plug-in power supply or from any computer USB port. The USB port is intended only for power and is not a data interface. -
Page 7: Connecting The Wutooth
W&T 2 Connecting the WuTooth 2.1 Pairing To use the WuTooth in the app the device must first be paired in your smartphone settings. This is done under:... - Page 8 W&T Activate the WuTooth by shaking until the red LED inside begins to flash. Now tap on “Find device” on your smartphone. After a short time your device will be shown in the list: Now tap on the desired WuTooth and confirm the following coupling prompt with “Accept”.
- Page 9 W&T...
-
Page 10: Wutooth App
W&T 3 WuTooth App The WuTooth app can be downloaded at no charge from the Google Play Store. Start the app after downloading from your smartphone menu. - Page 11 W&T Shake the WuTooth and tap on “New WuTooth”. The smartphone now begins to search for all devices within range. As soon as your WuTooth is displayed, select it by tapping on...
- Page 12 W&T The device now appears in your inventory list. Tapping on the WuTooth in your inventory list takes you to the device overview where you can use all the functions: - Display the current measurement values - Select, save and delete measurement series - Display average values - Display the saved measurement data in table format - Display the saved measurements as a graphic...
-
Page 13: Indicators
W&T 4 Indicators The WuTooth has two internal LEDs which indicate the status of the device. 4.1 LED indicators Red LED flashes twice briefly, green LED off: Ready for a connection. A connection to the device can be established. Red LED flashes once a second, green LED on: There is a Bluetooth connection... -
Page 14: Activating Bluertooth
W&T 5 Activating Bluertooth The various operating modes are configured using the configuration software. 5.1 Mode: Shake to activate In standard mode you activate the device by shaking it. This turns the unit on and causes it to wait for a connection. If no connection is established within 50s, the unit turns itself off and must be reactivated. -
Page 15: Mode: On Every X Minutes
W&T 5.2 Mode: On every x minutes The device is activated as in “Shake to activate” mode. In addition, the device activates itself automatically every full minute for 10s to enable a connection. This mode is recommended if the device is kept in a difficult to access location. -
Page 16: Instructions According To The German Battery Law
W&T 6 Instructions according to the German Battery Law Since the W&T WuTooth contains a battery or rechargeable battery, we are obligated by the German Battery Law (BattG) to inform you of the following. Batteries and rechargeable batteries may not be disposed of with household waste, rather you are legally required to return used batteries and rechargeable batteries. -
Page 17: Technical Data
W&T 7 Technical data Prod. No.: 97100 Communication: Bluetooth Power supply: 1 AA rechargeable battery, 1.2V, or 1 AA battery 1.5V Alternative: USB Micro Port for 5V supply via power supply Measuring unit: Sensor: Temperature sensor Measuring range: -25°C...85°C Resolution: 1/100 °C Measuring error: Temperature:... - Page 18 W&T Prod. No.: 97101 Communication: Bluetooth Power supply: 1 AA rechargeable battery, 1.2V, or 1 AA battery 1.5V Alternative: USB Micro Port for 5V supply via power supply Measuring Unit: Sensor: Combined temperature and humidity sensor Measuring range: -25°C...85°C, 0..100% relative humidity Resolution: 1/100 °C, 1/100% relative humidity Measuring error:...
-
Page 19: Weak Points
W&T 8 Weak points W&T is known as a manufacturer of long-lived, reliable products. But even we aren’t perfect. Especially when we take on new areas it can happen that weak points become evident whose solution we are already working on but which we unfortunately cannot resolve in our accustomed ra- pid manner: 8.1 Bluetooth Stack...