Anleitung W&T LAN Scanner (D/USA) 55504 / 55505 Inhalt Seite 1. Einleitung 2. Anschluß des LAN Scanner an das LAN 3. Überprüfung von Netzwerk-Installationen im laufenden Betrieb 4. History - Funktion 5. Wechsel der Batterie Anhang A: Anwendungsbeispiele A.1. Zu lange Kabel A.1.1.
1. Einleitung Mit Hilfe des W&T Permanent LAN Scanner III lassen sich Netzwerkver- kabelungen auf ihre Funktionsfähig- keit hin überprüfen. Der LAN Scanner arbeitet nach dem Prinzip der TDR - Reflektionsmessung und erkennt folgende Fehlerbedingun- gen: abgezogene Steckverbinder Kabelbrüche und Unterbrechungen Kurzschlüsse in Steckverbindern und Kabeln fehlende Abschlußwiderstände unzulässige Stichleitungen, etc.
INTERFACES Ethernet-Netzwerken bei laufendem Netzwerk durchführen, da alle Aktivitäten des LAN Scanners mit W&T LAN Scanner II EAN 40 10344 55504 9 dem Datentransfer auf dem Netzwerk synchronisiert werden. Der LAN Scanner arbeitet jedoch nicht ausschließlich mit Netzwerkkabeln, sondern prinzipiell mit allen gängigen Kabeltypen.
Zur Überbrückung dieser Distanz sollte ein 1 Meter langes Meßkabel zwischen Scanner W&T LAN Scanner II EAN 40 10344 55504 9 Meßobjekt eingefügt werden. 3. Überprüfung von Netzwerk- Installationen im laufenden Betrieb Zur Durchführung der Messung stellen Sie den Schalter für den Kabeltyp...
Page 5
Der LAN Scanner 55504 besitzt im Gegensatz zum Typ 55505 keine Einstellmöglichkeit für den Kabeltyp. Bei diesem TDR läßt sich die gemessene Kabellänge durch Multiplikation des angezeigten Wertes mit dem entsprechenden Korrektur- faktor aus Tabelle 1 ermitteln. Nach dem Einschalten stellt Ihnen der...
Meter oder Fuß angezeigt. INTERFACES Im Fehlerfall bewegt sich der Lichtimpuls nur bis zur Mitte der W&T LAN Scanner II EAN 40 10344 55504 9 Leuchtdioden-Balkenanzeige und läuft zum Ausgangspunkt zurück (wiederum analog zum reflektierten Testimpuls auf der Leitung).
In Verbindung mit dem zum Lieferumfang des Tester gehörenden Netzteil läßt sich mit dieser Funktion eine Überprüfung eines Ethernet Netzwerks über einen längeren Zeitraum realisieren. 5. Wechsel der Batterie Ein Wechsel der eingebauten Lithium- Batterie wird nötig, wenn bei Tageslicht grüne LED- Balkenanzeige nicht mehr erkennbar...
Anhang A: Anwendungsbeispiele Häufigste Ausfall-Ursachen für in Betrieb befindliche Netzwerke sind erfahrungsgemäß aufgetrennte Steckverbindungen oder zu lange Segmente. A.1. Zu lange Kabel A.1.1. Fehlersymptome Segmentlängen oberhalb der genormten Obergrenzen (Thickwire Ethernet: 500 Meter, Thinwire Ethernet:185 Meter) können die Zuverlässigkeit des Netzwerkes spürbar verringern.
Da bei dieser Messung die Terminierung des Kabels gestört wird, während der Messung kein Datenverkehr über das Netzwerk- Segment mehr möglich. A.1.3. Problemlösung Mit Hilfe der W&T Repeater 55613 und 55615 ist es möglich, die räumliche Ausdehnung von Thinwire Ethernet - Netzwerken über die genormte Obergrenze von 185 m hinaus zu erweitern.
A.2. Unterbrechung des Kabels A.2.1. Fehlersymptome Eindeutige Hinweise auf Unterbrechungen des Netzwerkkabels infolge aufgetrennter Steckverbindungen oder fehlender Terminatoren sind: Funktions-Unfähigkeit des kompletten Netzwerk-Segmentes Leuchten der "Partitioning LED", sowie verstärktes Leuchten der "Collision LED" eines eventuell eingesetzten Repeaters W&T W&T Thinwire Repeater Box INTERFACES Data Collision Data Collision...
A.3. Vorbeugende Maßnahmen Da Netzwerkkabel in den meisten Fällen als Bestandteil der übrigen elektrischen Installation in Kabelkanälen oder über Decken verlegt werden, ist die genaue Länge der Kabel zwischen Station und Kabelende selten bekannt. Als vorbeugende Maßnahme ist es daher bei Neuinstallation oder Modifizierung der Netzwerkverkabelung sinnvoll, eine Liste der effektiven Kabellängen zu erstellen.
Anhang B: Technische Daten 55504 55505 Meßbare Kabellänge: 1 m ... 1000 m 1 m ... 1000 m (RG 58) (RG 58) Auflösung: Meßfehler: +/-3.0 m +/- 1.5 m Anzahl der Meßwertspeicher: Korrekturfaktor für Signalgeschwindigkeit einstellbar: 0.6c - 0.9c Spannungsversorgung:...
Page 13
Instructions W&T LAN Scanner 55504 / 55505 Contents Page 1. Introduction 2. Connection of LAN Scanner to LAN 3. Checking Network Installations in Running Operations 4. History - Function 5. Battery Change Appendix A: Examples of Usage A.1. Over-long cable A.1.1.
1. Introduction Network cable functions can be checked by means of a W&T Permanent LAN Scanner III. The LAN Scanner works on the principle of the TDR reflection measurement and recognizes the following faults: dislocated barrel connector cable break or interruption short in barrel connector or cable missing terminator unacceptable branch cable...
LAN Scanner can be synchronized with the W&T LAN Scanner II EAN 40 10344 55504 9 data transfer on the network. The LAN Scanner, however, does not work exclusively with network cables but also with all usual types of cables.
In order to bridge this distance, a measuring cable of 1 metre in length should be inserted between the LAN W&T LAN Scanner II EAN 40 10344 55504 9 Scanner and the object to be measured. 3. Checking Network Installations in Running Operations...
Page 17
In comparison to type 55505, the LAN Scanner 55504 has no adjustment device for cable types. With this TDR, the measured length of cable can be determined by multiplying the displayed value by the corresponding correction factor in table 1.
In the case of a fault, the light impulse only moves to the center of the LED- W&T LAN Scanner II EAN 40 10344 55504 9 chain and runs back to the starting point (again, analogue to the reflected test impulse on the conductor).
Due to the function of the mains supply circuit which is part of the package delivered with the tester, the Ethernet network can be checked over a longer period of time. 5. Battery Change It is necessary to change the in-built lithium battery when the green LED bar display can no longer be read in daylight or when the right LED of the...
Appendix A: Examples of Usage The most common causes of breakdowns in networks which are in operation are, in our exerience, broken barrel connectors or over-long segments. A.1. Over-long cable A.1.1. Symptoms of Fault Segment lengths over the standard maximum limit (Thickwire Ethernet: 500 metres, Thinwire Ethernet: 185 metres) can noticeably reduce the reliability of the network.
Because the termination of the cable can be interrupted during this measurement, data cannot be transferred via the network segment while the measurements are being carried out. A.1.3. Solution of Problems With the help of the W&T Repeater 55613 or 55615, it is possible to extend the length of thinwire Ethernet networks beyond the standard maximum limit of 185 metres.
A.2. Interruption of Cable A.2.1. Symptoms of Fault Clear indication of an interruption of the network cable as a result of dislocated barrel connectors or missing terminators are: function breakdown of total network segment illumination of "Partitioning LED", as well as increased illumination of the "Collision LED"...
A.3. Preventive Measures In most cases, the network cable is laid as part of the usual electrical installation in the cable canals or above the ceilings, an so the exact length of cable between station and cable end is rarely known. For this reason, it is advisable to write a list of the effective cable lengths as a precautionary measure when first installing or modifying network cables.