NexxTech 6313014 Instructions

Operating Buttons
A. On / Zero / Off
B. Unit
C. Tare / Gross / Net
D. Sampling
Power On, Power Off, or Reset Zero
Press On button once to turn on the scale.
Press and hold On button for 1-second to reset the scale to zero.
(ZERO symbol will show in the display)
Press and hold On button for 3 sec to shut off the scale.
Unit Exchange
Press Unit button to change the unit on the scale.
The sequence for the scales' unit shows as : g(gram), oz(ounce),
ct (carat), dwt(penny weight) or ozt(troy ounce)
Tare Function
Place an empty container on the scale. After the reading is stable, press
Tare button for 2-seconds to go into tare mode. The LCD will display Tare
and Net symbols, and the reading becomes zero. In this situation the Zero
symbol "0" will not be displayed.
• Place object into the container. The net weight will show on the display.
Press Tare button once, the gross weight (the container and the object
weight combined) will show on the display.
• Press Tare button again. The scale will show the net weight of tare
object.
• Remove the tare object – leaving nothing on the scale. (zero and tare will
display at the same time). The Tare symbol will be cleared when you turn
off tare function. Press the Tare button for 2-seconds to shut off the tare
function.
The cover of the scale can double as the measuring plate for the scale
1. Open the scale's cover all the way,
detach the scale's cover from the
scale. Then, use the scale's cover as
a measuring plate.
Mini Digital Scale
INSTRUCTIONS
D.
Sampling Function
C.
Press pcs button for 2-seconds to set the sample pieces.
pcs pcs
ct ct
DISPLAY FLASHES S=10, S=20, or S=50 depending on the number of sample pieces set.
g g
oz oz
Choose the desired number of sample pieces by pressing pcs button. The display
dwt dwt
ozt ozt
A.
sequence shows as the following: 10>20>50>10. Stop pressing when the display shows
your desired sample pieces. Leave selected number on the scale for 2-seconds for the
B.
sample pieces to be set as the default.
• Press pcs button to go to sampling function.
S=10(10 pieces), S=20(20 pieces), or S=50(50 pieces) depending on the default sample
pieces setting. Put on the tray the exact number of sample pieces which is shown on
the display.
• Press pcs button again to confirm, "CAL" will show on the display when the scale is
doing the samples calculation.
After the calculation is done, the number of sample pieces which you had selected
(10, 20 ,or 50) and the Pcs symbol will show on the display. Scale is ready to do sampling.
• Place the object(s) on scale. The scale will count the sample pieces and will show
amounts on the display.
Holding Result for 5-seconds
After an object is placed on the scale, the objects weight will be displayed. Buzzer will
sound when the result is stable. After buzzer has sounded, the object can be removed
from the scale and the result will stay on the display for 5-seconds.
Auto Shut Off
The scale will automatically turn off after 3 minutes to save energy.
Low Battery Indication
Low battery symbol will show on the display if the battery is low.
Battery Requirement: 2 x CR2032 batteries (included).
Resetting the Scale
When the scale does not respond, remove, and reinstall the batteries to reset scale.
CAUTION
If the zero point is not stable, "UNST" will be displayed. The Total weight on the scales is
300 grams. If the scale exceeds its capacity, then "EEEE" will display.
2. The scale's cover can be
re-attached to the scale by
following the instruction in
reverse.
Detach the cover from the scale by
pushing straight down.
Separate cover and
place on top of scale.
Re-attach the cover by pushing scale
down onto the lid and snapping
the hinge back in place.
6313014