G2M™ (Version 3)
Universal MIDI Converter
Owner's Manual
Congratulations on your purchase of the
G2M™. Please take the time to read
through this manual to ensure you get the
best from your G2M™.
Introduction
What is the G2M™?
The G2M™ is a simple to use and highly
effective
converter. It's the fastest,
MIDI
most accurate, way to turn any musical
instrument into a
instrument.
MIDI
Your new "Version 3" G2M™ features
several enhancements compared to the
previous versions, including support for
bass-register instruments and the latest,
state-of-the-art pitch-detection algorithms
only available from sonuus.
Designed to give accurate triggering, with
ultra-low latency, it is a true plug-and-play
solution for converting monophonic audio
into
. It can be used to sequence bass
MIDI
lines and guitar solos, add an edge to your
live performances and to open up many
creative possibilities.
Connections
Instrument In
Connect your instrument lead to the
IN
socket using a standard ¼" guitar/
instrument lead.
MIDI Out
Connect your
device (or computer,
MIDI
etc.
) to the
socket using a
MIDI OUT
G2M™
standard 5-pin
lead. You can also
MIDI
power self-powered
devices such as
MIDI
mergers and message filters.
MIDI
MIDI In
You can send
controller messages to
MIDI
the G2M™ using a special
cable (available from sonuus) which
converts the
socket to both a
MIDI OUT
and a
socket.
OUT
MIDI IN
Instrument Thru
If you want to connect your instrument to
another device, or to your amplifier,
connect a lead to the
THRU
has a high-impedance input and it will not
affect the sound of your instrument while it
is connected.
Power
9V DC
Your G2M™ can be conveniently powered
by a 9V DC power supply. Its low current
requirement (<30mA) means almost any
standard 9V power supply can be used
(2
1mm centre-pin, positive tip).
·
Battery (AA)
For true portability, the G2M™ can also be
powered by a single AA battery (alkaline or
rechargeable). Simply open the battery
door and put in a battery observing the
correct polarity. If you connect it the wrong
way round it won't cause any damage, but
the unit won't operate until the battery is
inserted correctly.
Because of its low power consumption, the
unit will run for many hours (typically for
more than 20) on a single battery. When
jack
the battery is close to needing to be
replaced, the
LOW BATTERY LED
not necessary to replace the battery
immediately since the G2M™ will continue
to function normally. When the battery is
nearly exhausted, the
LOW BATTERY LED
flash and the battery must be replaced. If
you need the G2M™ to work reliably for
several hours (
when playing live) the battery should be
replaced if the
When battery-powered, the G2M™ is
switched on when a lead is plugged into
breakout
MIDI
the
jack. To maximise battery life, this
IN
jack must be disconnected when you are
MIDI
not using the unit.
Power-Save (battery-power only)
After 30minutes of inactivity the G2M™
will enter a low-power (but not fully off)
state to preserve the battery. To restart the
jack. The G2M™
unit, simply unplug and re-insert the lead
into the
jack.
IN
Using your G2M™ couldn't be simpler:
•
Plug your instrument (
guitar) into the
POWER LED
•
Connect your
etc.
) to the
•
If the
CLIP LED
instrument's volume so that the
lights only occasionally while
LED
playing normally.
•
Optionally, check your guitar/bass is in
tune using the built-in tuner (if you
want to tune to standard tuning).
•
Play your instrument to send
your
device (or sequencer,
MIDI
For your convenience, the G2M™ includes
a built-in tuner. This uses our PULSAR™
tuning technology where the
will light. It is
doubles as a tuning indicator. This
innovative tuner gives you a fast and
accurate way to tune your guitar or bass.
If there is no input signal, the
will
lit and indicates that the unit is powered.
G2M™
When there is an input signal, the
e.g.,
a recording session, or
pulse smoothly to indicate tuning.
When the note is out of tune, the
is lit.
LOW BATTERY LED
pulse quickly. As you get closer to the
correct pitch, this pulsing will slow.
Eventually when you are perfectly in tune,
the pulsing will stop. Normally, as long as
the
second, the tuning is close enough for most
purposes.
It is always best to start at a lower pitch and
tune upwards to the correct pitch. As you
get closer to the correct pitch and the
pulsing slows down, turn your tuning head
more slowly to avoid overshooting the
correct pitch. Because the tuner is very
accurate you will find that very small
Operation
movements may be all that is required to
move from slightly out-of-tune to in-tune (or
indeed, to go from in-tune to slightly out-of-
tune). With only a little practice you will find
e.g.,
electric
you can tune very quickly and accurately
jack socket. The
IN
using the PULSAR™ tuner.
will light.
device (or computer,
MIDI
socket.
MIDI OUT
lights, adjust your
CLIP
To capture all the nuances of your playing,
the G2M™ sends note-on (with velocity),
note-off, pitch-bend and breath controller
(#2)
Chromatic
to
The G2M™ accurately tracks the pitch of
MIDI
etc.
).
notes
messages but sometimes it is preferable to
send notes without pitch-bend information
Tuner
e.g.,
(
be done by enabling the
next to the
MIDI Pitch Bend Sensitivity
POWER LED
For pitch-bend, the most common setting
for most
bend to represent ±2 semitones, and this is
also the default G2M™ setting. It can also
will remain
LED
be set to ±5, ±12 and ±36. To ensure your
G2M™
will
LED
will
LED
pulses slower than once per
LED
MIDI
messages.
MIDI
and
outputs
pitch-bend
MIDI
when playing piano sounds). This can
switch
CHROMATIC
jack socket.
IN
devices is for full-scale pitch-
MIDI
G2M™
Need help?
Do you have a question about the G2M and is the answer not in the manual?
Questions and answers