Advertisement
2. On the Tools > Optional Features 1 > Common Page 3 screen set the following:
COM port number
Function
Polarity
COM port 0
GPS
N
3. On the Tools > Optional Features 2 > GPS screen set the following:
GPS Report Mode
Poll or Auto
GPS Message Type
Full
GPS Report Interval Time
1 to 3600 seconds
Speci cations
Receiver Type
Channels:
Frequency:
Signals:
Configuration
Time Pulse:
Navigation Update Rate:
1
Time-To-First-Fix
Cold Start (Autonomous):
Warm Start (Autonomous):
Hot Start (Autonomous):
Aided Starts
3
Sensitivity
Tracking & Navigation:
Reacquisition:
Cold Start (Autonomous):
Accuracy
Horizontal position
RMS 99%:
Velocity
Heading
Limits
Acceleration:
Altitude
Velocity
Note:
1.
All satellites at -130 dBm
Dependent on aiding data connection speed and latency
2.
Demonstrated with a good active antenna
3.
4.
CEP, 50%, 24 hours static, -130dBm, SEP: <3.5m
50% @ 30 m/s
5.
Assuming Airborne <4g platform
6.
DISCLAIMER: GPS location data is acquired from government satellites. Accuracy of this data is
subject to obstructions, re ections, interference, and government interventions, and is not under
PRYME's control. Users should avoid placing absolute reliance on coordinates obtained from any
GPS receiving device.
At best, GPS location reports are only accurate to:
• within 10 meters for latitude and longitude
• within 50 meters for altitude
In practice, accuracy is variable and is a ected by many environmental factors such as interference
and obstruction. Altitude is especially subject to inaccuracies. Ultimately, the reliability of the data
is under the control of the GPS source, not the GPS receive system
Stop Bit
Baud Rate
1
9600
This setting allows
the radio to detect
the GPS receiver in
the PRYME Trooper II GPS
Setting the GPS
Report Mode to Auto
allows the radio to
send out GPS
messages at set
intervals as
determined by the
GPS Report Interval
Time. Setting GPS
Report Mode to Poll
will cause the radio to
only send its GPS
coordinates
over-the-air if
prompted by the base
station radio/software.
5
50
L1
GPS C/A Code
0.25 Hz to 1 kHz
up to 5Hz (ROM)
28 s
28 s
1 s
2
:
1 s
-160 dBm
-160 dBm
-143 dBm
4
:
< 2.5 m Autonomous
< 2.0 m SBAS
30 ns <60 ns
5
:
0.1m/s
5
:
0.5 degrees
4 g
6
:
50000 m
6
:
500 m/s
7
4. On the Tools > NXDN > GPS screen set the following:
Voice Call
Checked or Unchecked
Status
Checked or Unchecked
GPS Report Status Number Block
1 to 207
Emergency
Checked or Unchecked
5. On the Tools > NXDN > General 1 screen set the following:
Base ID Type
Unit ID
Base ID
Enter the Unit ID of the base station radio
6. Go to the Key Assignments > Menu screen and add the following functions:
GPS Position Display
Send the GPS Data
Adding these two items to the menu will allow the radio user to both view the latitude, longitude,
altitude and speed data from the GPS receiver in the PRYME GPS-511 and also to manually send the GPS
location data to the base station over-the-air.
Support and Warranty
PRYME Radio Products warrants this product against defects in materials or
workmanship for a period of one year from the date of retail purchase. PRYME will
repair or replace a defective unit, at our option, without charge for parts or labor.
The limited warranty is extended only to the original purchaser and is valid only to
consumers in the United States and Canada. It does not cover damage or failure
caused by or attributable to Acts of God, abuse, misuse, improper or abnormal
usage, faulty installation, improper maintenance, lightning, or other incidences of
excessive voltage, or any tampering or repairs by other than a PRYME authorized
repair facility. It does not cover replacement of consumable parts, transportation
costs, or damage in transit.
Repair or replacement under the terms of this warranty does not extend the terms
of this warranty. This warranty can only be modi ed by an o cer of PRYME Radio
Products, and then only in writing. Should this product prove defective in
workmanship or material, the consumer's sole remedies shall be such repair or
replacement as provided by the terms of this warranty. Under no circumstances
shall PRYME Radio Products be liable for any loss or damage, direct, consequential,
or incidental, arising out of the use of or inability to use this product. Some states
do not allow limitations on how long an implied warranty lasts or the exclusions or
limitations of incidental or consequential damages, so the above limitations or
exclusions may not apply to you. This warranty gives you speci c legal rights. You
may also have other rights, which may vary, from state to state.
For support or warranty service on your PRYME product, contact us at 1-800-666-
2654 or visit us on the web at www.PRYME.com.
COPYRIGHT AND TRADEMARK INFO
© 2013 PRYME Radio Products, Brea CA. All rights reserved.
PRYME® is a trademarks owned by PRYME Radio Products. All other product or
service names are the property of their respective owners.
These settings determine
whether GPS data will be sent as
short messages in combination
with Voice, Status, and
Emergency calls made using the
radios digital modulation mode.
If you want the GPS locations to
also be sent using the radio's
analog voice mode, you must
also add the same settings to the
Tools > Fleetsync > GPS screen.
These settings specify which
radio on the system is being
used as the "base station" so that
GPS messages can be routed
correctly. The settings on this
screen apply to the radio's digital
modulation mode. If you want
the GPS locations to also be sent
using the radio's analog voice
mode, you must also add the
same settings to the Tools >
Fleetsync > GPS screen.
6
8
Advertisement
