Table of Contents
Advertisement
I n s t a l l a t i o n G u i d e
G u i d e d ' i n s t a l l a t i o n
M a n u a l e d i i n s t a l l a z i o n e
I n s t a l l a t i o n s a n l e i t u n g
G u í a d e i n s t a l a c i ó n
G u i a d e i n s t a l a ç ã o
I n s t a l l a t i e h a n d l e i d i n g
安 装 指 南
イ ン スト ー ル ガ イド
Р у к о в о д с т в о п о у с т а н о в к е
دليل الرى كيب
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Monitor Audio CLG140
Summary of Contents for Monitor Audio CLG140
- Page 1 I n s t a l l a t i o n G u i d e G u i d e d ' i n s t a l l a t i o n M a n u a l e d i i n s t a l l a z i o n e I n s t a l l a t i o n s a n l e i t u n g G u í...
-
Page 2: Table Of Contents
5 Introduction Bring high fidelity sound to the great outdoors with Monitor Audio’s latest custom installation solution, the Climate Garden Series. Designed from the ground up with high quality components and construction to take whatever the weather can throw at them. -
Page 3: Wiring The Speakers And Subwoofer
Wiring the Speakers and Subwoofer The CLG140/ CLG160 speakers work off a 100v/ 70v system and CLG-W12 can work off a 100v/ 70v system or can be hooked up to a conventional amplifier (8 Ohm tap). NOTE: This will not work if connected to the subwoofer output at phono level. A 70v Line system is mainly used in the U.S whereas the U.K and Europe use 100v line systems. -
Page 4: Installation
(such as the Crown CDi 2000) connect cables. If using the CLG140/ CLG160 speakers there to the black and red cables, for conventional 8 ohm is no reason the cables for these cannot be doubled lines connect to the yellow and black. -
Page 5: Clg140/ Clg160 - With Spike
CLG140/ CLG160 - With Spike First screw the threaded section supplied Once assembled, the speaker (i) onto the CLG140/ CLG160 speaker, once can now be installed in the secure thread the cables attached to the speaker desired location. through the hole in the spike before attaching the spike to the threaded section (ii). -
Page 6: Clg140/ Clg160 - Wall Mount
Place location with a single screw (i), then the CLG140/ CLG160 (i) onto the bracket and fit the insert the ball fixing arm and top half of the mount grub screws (ii) but do not fully tighten. Adjust the assembly, attach loosely with four screws (ii). -
Page 7: System Setup
Mono System With Monitor Audio’s preset DSP settings installed (refer to page 6 and 7) and the ‘CLG DUAL’ preset selected on the amplifier the Crown CDi 2000 will send mid-high frequencies to channel 2 and bass frequencies to channel 1. Connect the sub to channel 1 and the satellites in parallel to channel 2 (expandable to a maximum of 30 speakers). -
Page 8: Stereo System
Stereo System With Monitor Audio’s preset DSP settings installed (refer to page 6 and 7) and the ‘CLG SATS’ preset selected on the amplifier the Crown CDi 2000 will play the left audio through Channel 1 and right through Channel 2 (both expandable to a maximum of 30 speakers). -
Page 9: Installing Ma Presets On Your Crown Cdi 2000
Connect the Crown CDi 2000 via USB cable to your 11. Open the Monitor Audio preset file. computer and switch on the power button, the ready 12. You have now successfully installed our Monitor Audio LED and power button will become illuminated. presets on your Crown CDi 2000. -
Page 10: Amplifier
Specifications CLG140 CLG160 Frequency Response (-6dB) 100Hz – 30KHz 80Hz – 30KHz Sensitivity (1W@1m) 88dB 89dB Line Level Voltage 70/100 70/100 Maximum S.P.L 104 dBA 107 dBA 40 watts (crossover set to minimum 60 watts (crossover set to minimum Power Handling... -
Page 11: Guarantee
Monitor Audio reserves the right to alter specifications without notice. Guarantee Both the craftsmanship and the performance of the CLG140/ CLG160 and CLG-W12 is guaranteed against manufacturing defects for a period of five years from the date of purchase (see conditions in the Important Safety Instructions booklet), provided that the product was supplied by an authorised Monitor Audio retailer under the consumer sale agreement.
Need help?
Do you have a question about the CLG140 and is the answer not in the manual?
Questions and answers