Advertisement
remote control
(max. 3x)
push button
LED indicator
Immobilizer CA-322 „Accent"
Arming
After switching off the ignition, removing your key and exiting the
vehicle, close all the doors (closing of all windows is also
recommended). ARM the immobilizer by pressing the button (
or
) on the remote control.
One flash from the turn lights confirms arming and the LED starts
to flash. At the same time the immobilizer is blocked and the doors should
automatically lock (if equipped with central-door locks). If a powered window
control system is also connected to the „lock" signal, all the windows will be
closed automatically* when button
does not have any influence on the windows).
Disarming
To disarm the immobilizer press a button (either
The turn lights should flash twice. At the same time the doors should unlock
(if equipped with central-door locks) and the LED should turn off. When you
open a door the dome light will come on for 60 seconds or until you switch on
ignition key.
REARM* - if you do not enter the car within one minute after disarming, the
immobilizer will rearm and lock the doors automatically again.
AUTOIMMO*
will block the car automatically if the ignition key is turned off for
more than 5 minutes. This immobilization (doors stay unlocked) is indicated by
intermittent LED light. The immobilization can be switched off by a remote
control button (
or
). It will also switch off if you switch on the ignition key
and press the VALET button /*. Automatic immobilization can also be
temporarily disabled if you switch off the ignition key while the VALET button
is pressed. The AUTOIMMO function will be disabled until the remote control
Examples of „Accent" use for different central locking systems
If your locking system needs another kind of control signal than negative
pulses, install a couple of over-switching relays to the Accent outputs (or you can
use CR-2 relay unit). See following diagrams for different locking systems.
System with positive control inputs:
Pneumatic central locking system:
Program duration of output pulses 2 or 4 seconds according to the reaction
time of the pneumatic system.
Immobilizer CA-322 „Accent"
VALET
1
battery
12V
el. powered
windows
4
central
lock
5
locking
unlock
is used for arming (button
or
) on the remote control once.
antenna
CA-322
main unit
3x immobilization contacts
(3x max. 15 A)
5
6
1
2 4
8
13
14
2
dome
light
7
+12V
6
ignition
key (15)
is activated again. This can be used, for example, when you leave your car in
a car shop for maintenance without the remote control.
Emergency Disarming*
If you lost your remote control, perform following: Open the car door, switch
on the ignition key and press the hidden VALET switch.
Note: If emergency disarming was disabled in setting mode, there is no way
to disarm the immobilizer (call service).
No reaction of Immobilizer to remote control
If there was any attempt to scan the remote control code (or while rare, as
may happen after the remote control battery has been replaced) then the
immobilizer will not respond to the signal from the remote control. In this case
arming
the system asks you for a confirmation of control code validity.
To provide, make Emergency Disarming (if armed), switch on the ignition
key and press the button of the remote control (
remote control should work as usual (if not, go to service).
Note: this way your system performs more complicated analyses of coding
system. It insures your immobilizer is secure from outside interference and
the remote control is indeed yours.
Maintenance
There is no special maintenance required. If the distance from your car at
which the system can be operated continuously decreases, then replace the
remote control battery (after releasing of a screw on the rear side of remote
control housing; mind the battery polarity). A suitable replacement battery is
L1016 (6VDC). Usual good battery life time is one year.
We recommend a yearly professional inspection of the immobilizer. Periodic
inspections should be made to the door switches.
We recommend installer
to the customer after installation, to avoid problems and misunderstandings in
future.
Simplified additional installation of central locking system:
manual operation of the whole system from the driver's door is not requested,
you can use the following easy solution. Install two-wires actuator
(recommended type CM-2) to each door of your car. Connect them as shown in
the following diagram. Program duration of Accent output pulses 0.3 seconds.
This way all actuators are operated with the remote control.
When necessary, the door locks can also be operated manually with a key
(the same way as before the central locking installation).
Caution : In this case do not use longer locking signal !
2 / 2
turn
indicators
L
R
14
13
2
4
1
3
AL1 input
8
trunk switch
door switches
- operating instructions
to give a detail explanation of „Accent" functions
* these functions are selectable in setting mode
or
). After that the
When
Pod Skalkou 33
466 01 Jablonec nad Nisou
Czech Republic
Tel.: +420 483 559 999
fax: +420 483 559 993
Internet: www.jablotron.cz
MDF532 06
Advertisement
