SAGEMCOM D17T User Manual

D17 D17 D17
I NTRODUCTION B EFORE YOU BEGIN
Make sure your package includes the following: Base unit, handset, one battery compartment cover,
Dear customer,
telephone line cord, AC power supply, two rechargeable batteries, and this user guide.
Thank you for purchasing a Sagemcom DECT telephone we appreciate your trust in us.
This product was manufactured with the utmost care, should you encounter difficulties during its use we
In the case of purchasing a pack duo or trio, you will find in addition for each additional handset: a
recommend that you refer to this user guide. You can also find information on the following site:
handset charger, one battery compartment cover, two rechargeable batteries.
www.sagemcom.com
For your comfort and safety, we ask that you read the following section carefully: Installing the phone
R
ECOMMENDATIONS AND SAFETY INSTRUCTIONS
Your DECT telephone must not be installed in a humid room (wash-up room, bathroom,
laundry room, kitchen, etc.) unless it is 1.50 m away from a water point or outside. Your
telephone must be operated at temperatures ranging from 5°C and 45°C.
Only use the supplied power adapter, connect it to the base socket according to the
installation instructions provided in this booklet and the indications on the identification
label affixed to it (voltage, current, electric network frequency). As a precaution, in case
of danger, the mains adapters act as a disconnecting mechanism for the 230V power
supply. They should be placed near the device and should be easily accessible.
This telephone was designed for use on the public switched telephone network (PSTN).
In case of a problem you must first contact your reseller. Only use the supplied
telephone cord.
For your personal safety, never place your handset on the base without the batteries,
or without the battery cover, you could get an electric shock.
To avoid damaging your handset, only use certified rechargeable AAA batteries NiMH
1.2 V 400 mAH, never use non rechargeable batteries. Insert the batteries in the handset
battery compartment respecting polarity.
At the end of their useful life, batteries must be disposed of according to the recycling
1. Insert the batteries, taking care to respect the polarity as indicated in the compartment.
instructions presented in this booklet.
2. Put the compartment door back on. «SEARCHING...» appears on the screen.
3. Plug the power supply cord into AC outlet and the other end into the power jack on the base
Your DECT telephone has an inside radio range of about 50 metres and up to
300 metres in open space. The immediate presence of metal parts, (of a television for bottom.
4. Plug one end of the telephone line cord into the modular wall phone jack and the other end into
example), of any electric appliance may result in range reduction.
the jack on the base.
Some sensitive medical equipment and safety equipment may be affected by the radio-
5. A welcome message in all the languages supported by the telephone is displayed on the screen,
frequency transmissions of your telephone. In all cases, we ask that you respect the
safety recommendations.
press
In areas where storms are frequent, we recommend that you protect your telephone line
6. Select the country using
using a surge protection device .
7. A screen asks you to confirm your choice. Press
This equipment does not function in the case of an electric network shutdown: for
emergency calls, it is recommended to use another unit during power cuts. You will hear a confirmation tone.
8. Place the handset in the base station to charge for 15 hours prior to first use.
The CE marking certifies that the product meets the essential requirements of Directive
1999/5/CE of the European Parliament and of the Council pertaining to microwave radio
9. After charging, press
equipment and telecommunication terminal equipment, for the safety and health of
users, for electromagnetic interference. Furthermore, it efficiently uses the frequency
spectrum attributed to ground and spatial communication to prevent damaging
interference.
The declaration of compliance may be looked up on the www.sagemcom.com site
"support" section or can be obtained from the following address :
Sagemcom Broadband SAS
250, route de l'Empereur - 92848 Rueil-Malmaison Cedex - France
* : depending on version
1
D17 D17 D17
4. A confirmation screen appears.
5. Press
5. Using the telephone touch keys:
6. Enter the name of the entry and press
- If you do not wish to delete the current record, press .
7. Enter the number of the entry. Press
- To delete the current record, press .
To call the number you have assigned to one of the shortcut keys. Hold down the key on which the
P HONEBOOK
number was programmed (
You can store 80 phonebook entries (24 digits and 12 characters) in your phonebook.
Inserting a pause (in dialling)
Dialling a memory number
You can insert a pause in dialling a phone number if you want to wait before actually ringing.
1. Press key to consult the list of contacts.
While dialling the number you want to call, press and hold the key
2. Press the or key to consult directory entries.
display shows a ’’P’’.
3. When you have selected the desire number, press .
U
SING THE MULTI
Creating / Storing a memory
These functions are used for handset management when two or more handsets are registered on the
1. Go to the menu " phonebook " / " new entry "
same base.
2. Enter the name of the entry. Press .
Intercom Call/Intercom
3. Enter the number of your entry using the keypad keys. Press .
1. Make sure your handset is on standby mode.
Editing a memory 2. Press the
1. Go to the menu " phonebook " / " edit entry ". - If your installation has two handsets, the second handset is directly called, and, "handset "
followed by the handset number are displayed on the screen.
2. Select the entry you want to edit using or . Press .
- If your telephone installation has more than two handsets, the icon INT blinks on the screen
3. You will then enter the name input screen and the cursor will be at the end of the name :
and the number of all registered handsets.
- Enter the desired handset number or press the
- The information is accurate. Press key.
Answering an internal call
- To correct the name, press key to delete characters.
1. The ring melody from an internal call is different from an external call. " handset " and the calling
- Enter the new name and press key. handset number appear on the screen. The " " is blinking.
4. You will then enter the number screen and the cursor will be at the end of the number :
2. Press the
- The information is accurate. Press key.
3. Ending an internal call press the
- To correct the number, press key to delete the numbers.
Managing an external and an internal call
- Enter the new number and press key.
Transfering an external call to another handset registered on same base
Deleting a memory / the whole phonebook 1. During a call, press
2. Enter the internal call number. When the user answers, you can announce the call.
1. Go to the menu " phonebook " / "delete " (or " delete all " to delete the entire phonebook list).
3. Press the
2. Select the entry you want to delete using or . Press :
- If you do not wish to delete the entry, press .
To switch from one call to another, press and hold down the
signal is heard.
- To delete the entry, press key.
Assign a shortcut
If the called handset does not answer, press
This menu allows you to record two quick dial numbers assigned to the keys 1 and 2 on the keypad.
1. Go to the menu " phonebook " / " direct mem. ".
2. Select the key you want to assign a number ( or ).
3. Press , " no number " is displayed on the screen.
4. Press , " eidt number " appears on the screen.
7
D17 D17 D17 D17 D17 D17
Handset keys
Screen
OK key:
Selection / Validation
Rechargeable
Paging button
batteries
- Pressed briefly : telephone set paging.
Green key:Talk on
- Hold down pressed (4 seconds minimum) :
telephone set registration.
Menu key
R key:
Second call / conference
Access to voice messaging
service (Press and hold) *
Telephone socket
Power socket Activate, deactivate keypad
lock (Press and hold)
Activate / Deactivate the
microphone
Microphone
* The voice mail number can be programmed.
To change it, refer to «Assign a shortcut» page 7).
*. Quick guide to handset display icons
or keys, press .
Signal strength icon (blinking when no signal or the signal strength is weak).
.
Call (blinks when you receive a call)
Answering machine icon (appears when answering machine is activated)
key. You can hear dial tone.
Voicemail icon: indicates that new messages are present in your voicemail box.
Handset ringer muted.
Received call list (appears when a new call is in the caller list).
Phonebook icon (appears when you enter to the phonebook list).
Charging status icon (
during charging).
2
D17 D17 D17 D17 D17 D17
Making conference calls (3-way conversation)
.
You can connect one external call to two handsets registered at the base station. To set up a
to confirm.
telephone conference from an external call:
1. Press key. The external user is put on hold.
to confirm. You will hear a confirmation tone.
2. Enter the internal call number. Wait until the internal user answers.
3. Press and hold key, until an aural signal is heard to start a three-way conference.
"conference" is displayed on the handset screen.
or ).
Two outside calls
Taking a second call while you are already on line
During a call, a beep is emitted by your operator to inform you that a second call is on hold. A screen
to insert the pause: The
displays the number of this second caller on hold.
Press then the key to take back this new call.
-
HANDSET CAPABILITIES Your first contact is put on hold and you can talk with the second caller.
Making a second call while you already on line
During a conversation, press
The call in process is then put on hold and you can take the second call back.
Switching from one call to the other
key on the handset.
To switch from one call to the other, press
The call in process is then put on hold and you can take the second call back.
Ending one of the two calls
key if you want to call all handsets.
To end one call and continue with the other, press
The call in process is then ended finally and you take the second call back.
To set up a 3-way conference (the 2 calls and yourself)
During a conversation, press
You can then talk with the 2 contacts at the same time.
key to answer. The " " stop blinking.
To end the 3-way conference, press the red key
key.
. The external user is put on hold.
key to transfer the call.
key until an aural
to take back the call.
8
Changing the batteries
Make sure the telephone is OFF before you replace batteries.
1. Remove the batteries compartment door.
2. Remove old batteries.
3. Insert the new batteries.
Earpiece
4. Put the batteries compartment door back on.
5. Place handset in the base to charge.
Navigation key up /
M ENU STRUCTURE
Access the caller list
Quick reference
Back key / Cancel /
Correction /
phonebook New entry Advanced set
Change standby screen
List
(Press and hold)
Edit entry
Red key:
delete
Talk off /
Switch handset on/off delete all
Directe mem.
Access to phonebook /
Navigation key down
Personal set Handset name
Handset tone
LANguage
Access to outgoing call list
Auto hang-up ANSW MACHINE**
Deactivate / Activate handset
ringer (Press and hold)
Clock&alarm date / time
Set format
Intercom key
Alarm
Alarm tone
* depending on version
** D17V only
Navigation
To navigate among the menus, use the keys: ,
Example: To change the ring tone, go to the menu Personal set / Handset tone / ring tones.
To do this:
1. Press . Select " Personal set " using the
2. Press . Select " Handset tone " using the
3. Press . Select "ring tones " using the or
4. Press . 10 melodies are available: " melody 1 "… " melody 10 ".
Select the desired melody using the or key.
: Full ; + flashing (charger not connected) : Flat; blinking
5. Press key to confirm your selection.
3
C USTOMISING THE HANDSET
Handset naming
handset N
The default name of the handset is " " where
1. Go to the menu " personal set " / " handset name ".
2. Use the keypad to enter the new name (up to 10 characters).
Use key to delete wrong input if necessary. Press
Handset ringer level
1. Go to the menu " personal set " / " handset tone " / " ring volume ".
2. Use or to select the volume level then press
Handset ringer melody
1. Go to the menu " personnalis." / " handset tone " / " ring tones ".
Ten melodies are available: " melody 1 "… " melody 10 ".
then dial the number to be called.
2. Use or to select the ring tone. Press
Key tone On/Off
1. Go to the menu " personal set " / " handset tone " / " key beep ".
then the key .
An information screen shows you the current state. Use
2. Press key to confirm your selection.
Modifying the language
1. Go to the menu " personal set " / " language ".
then the key .
2. Use or to choose the desired language. Press
Auto talk off
then the key .
When active, the auto talk off feature enables you to automatically hang up as soon as you put the
handset on its base.
.
1. Go to the menu " personal set " / " auto hang-up ".
An information screen shows you the current state. Use
2. Press key to confirm your selection.
Key lock
1. Press and hold key for 1 second. An information screen shows you that the keys are
locked.
2. To recover to normal, press and hold key 1 sec.
9 10
D17 D17 D17 D17 D17 D17
C ALLS
Make a call
Ensure that the handset is switched on.
1. Press the Talk key . you will hear the dialling tone and the display will show you the phone
icon .
2. Enter the phone number.
- OR-
1. Enter the phone number first and then press key.
Change pin
Answering a call
registration
When the phone rings, press the key to answer the call.
Unregister
You can adjust the volume of what you hear through the handset at any time by
Country*
pressing or key.
reset
Ending a call
AUTO PREFIX*
To end a call press .
Recall time
Dial mode* Microphone mute function
First ring - Enable MUTE function: press the key. The display shows "mute on".
- Disable MUTE function: press the key. Your correspondent can hear you again.
PLAY Voice Mail (According to operator)
With this function you can receive calls in your absence on a voice message recorder in the switched
DELETE ALL
telephone network. To indicate that a new message has been received the envelope icon
ANSW. ON/OFF
the new event message " voicEmail " are displayed on the Handset screen.
RECORD OGM
Your voicemail number is not set in the factory.
ANSWER MODE
SETTINGS
1. Dial the number of your operator’s voice message recorder.
2. The envelope icon disappears when there are no more new messages.
, and or ( or ).
or key.
or key.
key.
4 5
D17 D17 D17 D17 D17 D17
S ETTING THE DATE AND TIME
Time and date
N
is the number of the registered handsets.
After a power cut the time has to be reset.
1. Go to the menu " clock & alarm " / " date/time". Current date is displayed.
.
. - To keep the date, press
- To change it, enter the new date in 20YY/MM/JJ format.
.
- To go back to change the entry
2. Press . Current time is displayed.
to confirm your selection.
- To keep the time, press .
- To change it, enter the new time in the HH : MM format.
(If, after entering the time, the time format is 12H, use the
set pM).
.
.
- To go back to change the entry
3. Press .
Hour format
or to modify it.
1. Go to the menu "clock & alarm " / " set format " / " time format ".
A screen displays the current format, use or to change it.
2. Press .
Date format
key to confirm your selection.
1. Go to the menu "clock & alarm " / " set format " / " date format ".
A screen displays the current format, use or to change it.
2. Press .
Alarm clock
1. Go to the menu " clock & alarm " / " alarm ".
or to modify it.
To activate the alarm once, select "on once ".
To repeat the alarm each day at the programmed time, select "on daily ".
To deactivate the alarm, select "off ".
2. Select your choice then press .
Enter the time when you want the alarm to go off: "HH – mm ".
(If, after entering the time, the time format 12H, use key to set a a M and the
3. Press .
Modifying alarm tone
1. Go to the menu " clock & alarm " / " alarm tone ".
3 melodies are available: "melody 1", "melody 2" et "melody 3".
2. Select the desired melody, press key to confirm your selection.
You will hear a confirmation tone.
11
C ALL LOG
Calling Line Identification Presentation (CLIP)
This CLIP phone stores and displays CLIP information provided by your local telephone company.
You must subscribe to CLIP service in order to use this unit.
If you have not subscribed to CLIP service or if the caller number is suppressed, the display shows
"unknown".
Display of numbers not available:
- Unavailable: you are not in same area as your contact.
- Hide id : your contact does not want its number to be displayed.
Received call log
The received call log presents the calls you received. (max.10 last calls).
1. Press , the icon is displayed.
2. The most recent name or call number is displayed according to whether your contact's number
is included in your phonebook or not.
3. Press to display the date and the time of the call.
4. Press the or key to go through the list.
If the number is too long (more than 12 digits), the screen will not show the number
in full.
Press key to go to last number page for CID length.
Dialled call log
The dialled call log presents the calls you made (max. 5 last calls).
and
To consult the list:
1. Press briefly .
2. The last dialled number is displayed. Press the or key to consult the list of the last 5
numbers dialled.
Calling back a caller
1. Press the or key.
2. Press the or key to select a call record.
3. Press the key to dial the number.
Making an entry in the directory from the list of calls received.
1. Press the or key.
2. Use or to select the desired caller number.
3. Press key, then select "save number ".
4. Enter the name of the entry. Press .
Deleting caller list record
1. Press the or key.
2. Press or key to select a call record.
3. Press .
- Select " delete " to delete the current record.
- Select " delete all " to delete the entire Caller list.
6
A DVANCED SETTINGS
Base master PIN code
Your base station code (default setting 0000) is required to access certain security functions. This
may be at least 4 digits and a maximum of 8 digits.
1. Go to the menu " advanced set " / " change pin ".
2. Enter your old code first, press .
3. Enter your new PIN code.
Each time a digit is entered the «_» is replaced by a «*».
4. Press key to confirm your new PIN code. You will hear a confirmation tone.
Carefully note your base station code. You will need it to change certain settings.
Association of handset & base
key to set aM and the key to
1. Press and hold key for 5 seconds (after 1 minute if no Handset has started association
process the base goes back to standby).
2. Go to the menu " advanced set " / " registration ".
3. Enter the 4 digit base master PIN code (default 0000). Press .
4. Once the handset is registered. The handset automatically exits the registering mode.
5. The handset number assigned automatically by the base appears on the screen.
Disassociation of a handset
1. Go to the menu " advanced set " / " unregister ".
2. Enter the 4 digit base master PIN code (default 0000). Press .
3. Select the handset you want to delete using the or key then press (at standby state,
"pls reg h/s" is displayed on the screen).
Modifying the country (depending on version)
1. Go to the menu " advanced set " / "country ".
2. Enter the base master PIN code (default 0000). Each time a digit is entered the «_» is replaced
by a «*». Press key to confirm.
3. Using the or key, select the country where you will use the telephone. Press
4. A confirmation screen appears, press .
The message "wait.." appears on the screen. You will hear a confirmation tone.
key to set pM).
Restoring the Handset / Base Default Settings
1. Go to the menu " advanced set " / " reset ".
2. A confirmation screen appears, press .
12
D17 D17 D17
D17 D17 D17
.