RITS-N IRM203-UNI User Manual

IRM203-UNI

User Manual

. 1 D e c s i r t p o i n
Cover
Menu button
Connector
Change settings button
Menu display IR angle adjustment screw
Set (Apply) button
IR angle scale
Radar sensor unit
Indicator LED Radar sensitivity
volume
(Green/Red/Blue)
IR sensitivity
Settings display
IR sensor IR detection area
volume
unit adjustment

4. Mounting Precautions

Mounting height of Mount within 50mm of Ensure that there are
3m (9.8 ft) or the bottom of the door no moving objects in
lower. engine cover. the detection area.
3m
(9.8ft )
Make sure that the Ensure the minimum
If possible, ensure there is
sensor is not directly of reflected sunlight
no accumulation of snow
exposed to heavy from the floor.
or water on the floor.
rainfall.
Infrared detection area setting to maximise pedestrian safety.
A
A B
Moving door leaf Moving door leaf
B
Side view
Plan view
6. Mounting & Wiring Information
① Attach the mounting template so that it is
② Drill screw (mounting) (Ø3.5mm)
placed within a 50mm distance from the and power cable (wiring) (Ø10mm)
bottom edge of the door engine cover. holes.
Max 50mm Max 50mm
④ Controller wiring
Red
Power (AC/DC 12V~24V)
Black
White
Activation Output
Green
Yellow
Safety output
Blue
Gray
Test Input + (DC 12~24V)
Test Input -
Brown
⑥ Connect the power connector. ⑦ Attach the cover.
Cable Length(Min) 80mm
. 2 E x e t i r r o i D m e n s o i n s
Accessories
Mounting
template
265

3. LED Indicators

User Manual
Green
Cable 2.5m
Blue
LED Indicators
Red
Mounting screws
IRM203-UNI
Ensure that no
Infrared & Radar sensor detection
condensation gets
onto the sensor.
AC DC 12~24V
( ), ( )
~
AC12V: 300[mA] (Max) / AC24V: 200[mA] (Max)
Power consumption
DC12V: 160[mA] (Max) / DC24V: 80[mA] (Max)
Use different frequency Test input
6[mA] @ 24[VDC]
settings for sensors
Weight 250[g]
in close proximity.
Color Black
1 2
-20 ~ 50[ °C]
The Radar sensor unit
0.5 seconds
may be negatively affected
by metal close to or
in the detection area.
③ Use a flathead screwdriver to remove cover.
⑤ Attach the sensor to the door
⑧ How to remove the cover after installation
1. Insert a flathead screwdriver as shown
2. Turn the screwdriver counterclockwise gently to prise the cover from the sensor body
Infrared presence
timer setting
60
42.5
Unit : mm
Frequency
Standby
Setting
Radar detection
Safety Relay
Output
IR or IR+Radar detection
Radar unit
direction
detection
Activation
Relay Output
±10 [%] @ 50/60[Hz]
Activation
Relay
Output
Configuration
TEST Input
Low reflection
setting
Factory
reset

8. Detection

IR detection area depth adjustment
Screw
WARNING
Near
DO NOT use any
Removing/assembling the Radar Sensor Detection Module
flat head screws.
1.
Twist with your index finger
in the indicated direction.
2.
Hold and pull forward the upper part of the
module with your index finger.
IR detection area width adjustment
[ Near ]
[ Far ]
1.0[m] -0.5
1.0[m] -0.5 1.0[m] -0.5
0 0
0
-8 Angle setting +4 Angle setting
1.0
1.0
Narrow
Door Door
2.0 2.0
2.2
2.2
3.0 3.0
Wide
3 2 1
row row
row row row
Far
※Ensure that detection setting does not exceed the door.
Radar detection area adjustment
3.
After removing the module, turn 90 degrees
clockwise, and re-assemble.
90°
m
2 sec 30 sec 60 sec
O N C N
U i n i B
O N C N
+ + +
+
without TEST With TEST without TEST without TEST With TEST without TEST
0
. 2 [ 0 m ] 1.0 1.0 2 0 .
1.0
2.0
2.2
3.0
Narrow
Wide
(Installed height: 2.2 m)
(Default Sensitivity)
detection module
detection module
vertical angle
vertical angle
: 3 Step(15°)
S3
: 3 Step(15°)
S3
: 6 Step(30°)
S6
: 6 Step(30°)
S6
: 9 Step(45°)
S9
: 9 Step(45°)
S9
m m
m