alatech Star ONE WB001 Quick Start Manual

Star ONE GPS Running Watch
WB001
Thank you for choosing ALATECH Star ONE GPS Running Thank you for choosing ALATECH Star ONE GPS Running
Watch! Watch!
This smart sports watch features various transmission technologies including GPS,
Bluetooth and ANT+. To link with ALA CONNECT app (developed by ALATECH), the
device can pair with different sensors independently. This watch is your best partner
for daily activity and workout.

How to use

LIGHT
Click:
turn on/off backlight.
Hold:
1) turn on/off the device
2) lock/unlock the screen
3) don't disturb mode
UP
Click: to menu
Hold:
1) hold to contents menu.
2) hold to manually set on
/off of certain functions
under timer screen.
DOWN
Click: to menu
Start running
This watch, heart rate sensor and other ALATECH accessories are only consumer
electronics and assistive devices. The detected heart rate is for reference only and
ALATECH is not responsible for any incorrect value. Please consider your physical
condition when doing the activity. DO NOT only rely on the heart rate detected by
the assistive device and do activities with excessive intensity.
Please wear Star ONE GPS running watch on your wrist during the workout to
ensure correct detection of heart rate. The built-in optical heart rate monitor in
Star ONE Watch can directly detect heart rate from the wrist, it takes about 12~15
seconds to detect and please remain stable to ensure accurate detection of heart
rate.
1) In time display (standby mode)
Click to enter quick menu, select
2)
connect to GPS, optical heart rate or sensor. When the watch device display
"Start The Timer To Begin Workout" means GPS and optical heart rate sensor are
completed on connection. (Accessories sensors such as heart rate strap and
speed and cadence sensor must be paired in advance).
Apps
Run
Run indoor
3)
Click to start activity. During the activity, click
activity information. Hold to revise the training setting.
Run
4) Click again to pause timer.
• Save: Stop the activity and save activity information. Click
this activity information.
• Resume: Resume timing and continue activity.
• Discard: Delete this activity information.
• Calibration: Pace calibration.
Menu Mode:
1) Click to confirm.
2) ON/OFF switch.
Activity Mode:
Click to start,
pause activity.
Menu Mode:
Click to back the
perious page.
Activity Mode:
Click to manual lap
switch.
Compound key：click "START" and
+
"LIGHT" to QUICKY unlock the device.
Run/Bike and automatically
to check in time the
Distance
Speed
Timer
Bike
Quick Start Guide

Notice -Battery Charge

When using the device for the first time,
please charge it. To prevent corrosion,
please make sure dry and clean of charing
clip and back side of the device charging
terminal area before charing device.
1) Align charging terminal of charging clip with
back side of the device charging terminal.
2) Connect the charging clip securely to the device. After charging the device com-
START/STOP
pletely, please remove charging clip.

Broadcast Heart Rate

Star One has the function of broadcast
heart rate. You can use the device as sensor
of heart rate and also can be paired with
compatible devices BLE 4.0 or ANT+.
BACK/LAP
1) Click
2) On Heart Rate Screen, click
2) Read the compatible devices instruction of heart rate sensor,and pair the watch
with the devices. The heart rate monitor is paired and the heart rate screen is
already enabled.
4) Click turn off broadcast heart rate. Click
REMINDER
Under broadcast heart rate mode, not only is unable to view other
screen, but also other operating functions. It has to turn off broad-
cast heart rate, then operate the device.

Sensor Setting

You can purchase on the selection of the heart rate strap BLE 4.0 or ANT+, and
speed and cadence sensor. When using the sensors for the first time, please pair
with the watch.
HRM
Bluetooth
ANT+
Pair with Heart Rate Strap
Remove sensors from the watch device: Hold → Setting → Sensors → select
HRM or SPD/CAD → select Remove.

Connect Mobile

You can use ALA CONNECT APP to set up Star ONE, and also use Bluetooth to
synchronize the information.
1) Download APP from Google Play. (ALA
Connect)
2) Open and register APP. Make sure to
turn on Bluetooth and WiFi of mobile.
3) The watch device: Hold
Bluetooth → Pair Mobile and follows up
APP screen to match it.
4) The watch device will pop up a PIN
CODE, and key in to the mobile. If your
mobile doesn't pop up the "PIN CODE",
please try to pull down notification
toggle then get the pair PIN code from
the watch device.
to check
Remove the pair device:
ALA CONNECT APP →
Device → Unpair.
51
MIN
Heart Rate Page
to view heart rate screen.
to turn on the function of broadcast heart rate.
again, exit to time screen.
Hold → Setting → Sensors
SPD/CAD
Bluetooth
ANT+
Pair with Speed and Cadence Sensor
Hold → Setting → Bluetooth → Pair Mobile
→ Setting →
App Requirement :
Android 5.0 or Later
Bluetooth 4.0 or Later
Alignment
charging
terminal
92
Sign of Broadcast
58 65
Heart Rate
AVG MAX
4hr ago