DKS 2358-010 Quick Start

QUICKSTART "BASIC" HARDWIRE TRACKER EXPANSION BOARD TO RELAY 2/WIEGAND 2 GUIDELINES
For COMPLETE installation instructions, please refer to the HARDwired Installation/Owner's manual P/N 2358-065.
RS 232
MIC
VOL
3 2 1
SPK
VOL
FEED
BACK
3 2 1
CLK
SEN
ON Relay 0
MASTER
CODE
OFF
KEYPAD
NO NC
NO NC C
RING
13 14
1 2 3 4 5 6 7 8 9 10 11 12 15 16 17 18 19 20
2C 2RY
PHONE CGND PSW MIC COM SPKR IMD 5VDC IMC Z A BAT 16AC 16AC
1C 1NC 1NO
Central Office
phone line -
touch tone,
loop start. Switch closure across
terminals 4 & 6 will
Relay 2
activate relay 1 for its
programmed strike time.
Jumper
(Postal Lock)
Main Door/Gate
Relay 1 or Relay 0
Relay 1
Important Note: Relay 2 is used to
control tracker expansion board
Relay 2
addresses 3-10, Relay 1 or Relay 0 can
be used as the Primary Relay that will
open a visitor door or gate when the
N.O. Blue #17
resident pushes "9" on their telephone.
Com Brown #19
Access Control
System Board
ELEVATOR
1
2
3
Communication 2
Auxiliary
Terminal
Black #9-Com
Tracker expansion boards connected to Wiegand 2 will activate
White #8-Data 1
Relay 2 in the access control system.
Green #7-Data 0
Card Reader
Switch MUST be ON (1)
DK Prox Reader
for board address 10.
Aux
Power
Switch MUST be OFF (0)
for board addresses 3 thru 9.
Wiegand Access
Control Device
Note: If card
Main
reader has
26, 30, 31-Bit Wiegand
Power additional
lighting for
outdoor use,
separate power
must be
1
provided. 6 conductor, stranded with overall 2
3
shield, 18-22 gauge. 500 ft max.
4
DO NOT use twisted pair.
5
#6-Green = Data 0
6
#7-White = Data 1
7
#8-Black = Common
8
#9-Red = 12 VDC Power
9
10
#10 connects
11
ONLY to tracker
12
expansion boards
13
14
15
16
17
18
19
20
#20-Card Reader LED
OR Beeper Control
(Available on certain
card readers)
To #8 Com To #18
T O
S H
P U
I T Tracker Expansion
E X
Board "Busy" #10
Request to Exit Typical BASIC Tracker
(Free Exit)
NO "optional" tracker features or battery back-up wiring shown, see manual for details.
Tracker Expansion Board Enclosure Options
Single Board Enclosure with
Built-In Card Reader and Lighting
DK Prox Reader - P/N 1815-333
HID Reader - P/N 1815-392
AWID Reader - P/N 1815-292
First Board Address
Starts at 3
BOARD ADDRESS
ON
1
0
OFF
Set Output Power for electric
Relay Jumper
strike or magnetic
lock is NOT
provided by the
board. Use
RF OUTPUT ALARM AUX
SECURE 2358-010
BOARD ADDRESS RF RF CODE CODE CODE RELAY RELAY RELAY
DATA STATUS SENT GOOD BAD NC NC NC
separate UL listed
ON
NO NO NO
1
power supply.
0
21
22
Output Relay
23
24
#25 & #26
25
26
27
28
29
30
31 Ground #32
32
33
34
Ground
12 GA. Wire
RESET
ENT
Tracker Expansion
Board Power
16.5 VAC, 20 VA
Board Address 3
Required
18 GA. Wire 100 ft max
16 GA. Wire 200 ft max
Expansion Board
Wiring Options
for Access Point
Single Board Enclosure Quad Board Enclosure
P/N 2351-080 P/N 2351-081
Door Lock Control
Second Board Address
BOARD ADDRESS
Relay
Electric
Jumper ON
strike
1
0
OFF
Maglock
Relay
Jumper
Card Reader
OR
BOARD ADDRESS
ON
Gate Operator Control 1
0
1
2
3
4
5
Relay
6
Jumper
7
To #8
8
9
Red #10
10
11
12
13
14
15
Blue #17 16
To #18 17
18
Brown #19
19
20
T O
S H
P U
I T
E X
Request to Exit
(Free Exit)
Use 6 conductor stranded with overall shield. 18 - 22 gauge.
ONLY use 18 gauge when wiring more than 8 boards.
DO NOT connect shield to 2358-010 board common.
Communication Line
DO NOT use twisted pair.
Up to 12 tracker expansion boards can be HARDwired to relay 2/wiegand 2 at the access control system.
IMPORTANT: The maximum distance for a tracker expansion board HARDwire run is 4000 feet TOTAL (1 to 12 boards
can be in a HARDwire run). The farthest board can be NO more than 2000 feet away from the access control system.
See manual for multiple tracker expansion boards layout limitations.
120 Glasgow Avenue
Inglewood, California 90301
Tracker Expansion Board Notes:
All tracker expansion boards can be wired with
desired options for their access points like shown on
tracker expansion board address 3.
Communication line will continue for each board like
shown on tracker expansion board address 4.
Board addresses MUST start at 3 and contiunue thru
board address 10 (up to
BOARD ADDRESS
12 boards using Zone
ON
Addresses) if required.
1
Set to 4 0
OFF
Board Address 10
Setting
RF OUTPUT ALARM AUX
SECURE 2358-010
RF RF CODE CODE CODE RELAY RELAY RELAY
DATA STATUS SENT GOOD BAD NC NC NC
Lock
NO NO NO
Power
21
22
23
24
Electric Strike
25
Door Lock
26
27
28
29
30
31 Ground #32
32
33
34
Ground
RESET
ENT
Tracker
Board Power
Expansion
Board
Address 4
To Board Addresses 5 thru 10
U.S.A.