Disassembly/Assembly Procedures Of Deck Mechanism - Philips DVD740VR/051 Service Manual

DISASSEMBLY/ASSEMBLY PROCEDURES
Before following the procedures described below, be sure to remove the deck assembly from the cabinet. (Refer to
CABINET DISASSEMBLY INSTRUCTIONS on page 1-7-1.)
All the following procedures, including those for adjustment and replacement of parts, should be done in Eject
mode; see the positions of [45] and [46] in Fig.DM1 on page 2-4-3. When reassembling, follow the steps in reverse
order.
STEP START-
/LOC. ING
No. No.
[1] [1] Guide Holder A
[2] [1] Cassette Holder Assembly T
[3] [2] Slider L
Slider R
[4] [2]
[5] [4] Lock Lever
[6] [2] C Plate
[7] [7] Cylinder Assembly
Loading Motor Assembly
[8] [8]
[9] [9] AC Head Assembly
[10] [2] Tape Guide Assembly
[11] [10] Door Opener B
Pinch Arm (B)
[12] [11]
[13] [12] Pinch Arm (A) Assembly
[14] [14] FE Head
[15] [15] Prism
[16] [2] Slider Shaft
[17] [16] C Drive Lever L
[18] [16] C Drive Lever R
[19] [7],[10] Capstan Motor
[20] [20] Clutch Assembly(HI)
[21] [20] Center Gear
[22] [22] Cam Holder F
[23] [22] Cam Gear (B)
[24] [24] Mode Gear
[20],[23],
Mode Lever(HI)
[25]
[24]
[26] [22] Worm Holder
Pulley Assembly
[27] [26]
[28] [22],[25] Cam Gear (A)
[29] [20] TR Gear C
[30] [29] TR Gear Spring
[31] [30] TR Gear A/B
[32] [31] FF Arm(HI)
[33] [21],[25] Idler Assembly(HI)
[34] [25] BT Arm
OF DECK MECHANISM
PART
T DM3
DM4
T DM5
T DM5
T DM5
T DM5
T DM1,DM6
T DM1,DM7
T DM1,DM7
T DM1,DM8
T DM1,DM8
T DM1,DM8
T DM1,DM8
T DM1,DM9
T DM1,DM9
T DM10
T DM10
T DM10
B DM2,DM11 3(S-12), Cap Belt
B DM2,DM12 (C-1)
B DM12
B DM2,DM13 (C-2)
B DM2,DM13 (C-3),*(P-4)
B DM2,DM14 (C-4)
B DM2,DM14 (C-5), *(L-4)
B DM2,DM14 (S-15)
B DM2,DM14
B DM2,DM14
B DM2,DM14 (C-6)
B DM14
B DM1,DM14
B DM1,DM14
B DM1,DM15 *(L-5)
B DM2,DM15 *(P-5)
REMOVAL
REMOVE/*UNHOOK/
UNLOCK/RELEASE/
Fig. No.
UNPLUG/DESOLDER
2(S-1)
(S-2)
(S-3)
(S-4),*(P-1)
Desolder, 3(S-5)
Desolder, LDG Belt,
2(S-6)
(S-7)
*(P-2)
*(L-1),*(L-2)
*(P-3)
(S-9)
(S-10)
(S-11),*(L-3)
2-4-1
INSTALLATION
ADJUSTMENT
CONDITION
(+)Refer to Alignment
Sec.Pg.2-4-10
HC460DA