Ko Propo KR-212FHG Instruction Manual

2.4GHz FHSS 2ch Receiver
with Gyro senser
At this time we would like to thank you for purchasing the KR-212FHG. This product corresponds to the transmitters that are sold by our com-
pany, listed below. Please read this instruction manual before using this product. Also please read the instruction manual of the transmitter
being used.
Corresponding
Including: SetUp Tool & Connector Cap
Compattible Transmitter
EX-1K.I.Y, EX-10 eurus with RF-903FH or RF-904FH, EX-1UR with RF-
903FH
Please change the transmitter setting OUTPUT to 4ch.
This product is designed for use with electric powered cars. Cannot be used
with gas powered cars.
Name of Parts
Set Up Button
LED Lamp
Antenna
Set Up Tool
For your safety, please note the handling and use of this product.
The contents of this display show a possibility of death or where a serious injury may occur
Warning
Warning or a highly substantial damaging accident may occur.
●This product is manufactured for surface use radio controls. *Discontinue use for all other purposes. Discontinue use in the event of a thunder storm.
*There is danger of a lightening bolt striking the antenna of the transmitter.
●Discontinue use when consuming alcohol or medication that may hinder concentration or judgement. *Unexpected accidents are caused with a judge-
ment mistake.
●When rain and puddles are present, please discontinue use. *There are times when water enters into the equipment and control will be lost.
●Only use the batteries specified in the instruction manual of the transmitter.
●To turn the system on, start by turning on the transmitter then the receiver. To turn off the system, turn off the receiver first, then the transmitter in this
sequence.
●Please be sure to use only our products for the transmitter and servos. *Concerning the damage and the like, which is generated when combining prod-
ucts that are not our company's genuine products we do not owe responsibility.
●Altering the transmission module is inhibited by law and is subjected to penal code violations. Resolution remodelling of all products may result in the
cause of a short and other accidents. In addition, if this product is altered we will refuse repair service.
●Please do not use this product inside an airplane, hospital, near any automatic control equipment, medical electrical machinery and apparatus such as
fire alarms. In addition with respect to the law, if this product effects other radio equipment and electronic equipment, use must be discontinued at once.
This displays shows the possibility or a substantially damaging accident which can cause Attention
Attention
injury.
●Please avoid storage in a place of high temperatures and high humidity because it may cause the breakdown,damage and deformation of the product.
●Please note when using with an engine model, place where exhaust and the waste oil will not come into contact with the product.
*In case of submerging in oil or water, please send it out for repair.
●This product's performance is designed for use in the shown specified usage which is based on this instruction manual and the instruction manual of the
transmitter which is used. When the instructions are not understood, please contact our service department for advise.
●After verifying the safety of use, think of all the accidents possible and please enjoy with responsibility.
Our company cannot owe responsibility from the nature of the radio control models
And the customer assumes all responsibilities that result from this product being used.
For electric
Antenna Installation Location
powered models.
Please keep distance to the receiver site, due to noise sources
of the battery, motor, ESC, etc. If possible.
Also, keep away power condensers and shotki diodes that gen-
erate noise away from the receiver antenna if possible. Install
the receiver on the chassis flat and level.
Antenna
chassis
KR-212FHG
Instruction Manual
Technical Specifications
KR-212FHG Receiver
FHSS Radio system ,
D. D.S . c o m p at ib l e Re s p o ns e M o d e C o m pat i b l e (U LT R A /
ADVANCED /
SUPER / NORMAL / DD ADVANCED / DD SUPER / DD NORMAL)
Fail safe system ,Number of Channels : 2CH ,Power source : 4.8v-
7.4V Size : 28×18.3×18.5mm Weight : 7.9g
P: Power Port
Accesaries are connected.
2 : Channel2
ESC are connected.
1 : Channel1
Steering servo is connected.
B : Battery Channel
If it is need, Battery is connected.
Installing the Antenna
●Please use plastic mounts and a plastic antenna
tube.
●Please do not use a metal antenna mount because
it will create noise and problems.
●To protect the main antenna, insert the antenna into
theantenna tube. Also please do not disconnect or
cut the antenna. This will cause loss of signal.
Please do not cut the antenna wire. You will receive
l e s s r a n g e . Pl e a s e p l a c e a n t e n n a aw ay f ro m
Caution
receiver battery, ESC, motor and silicon wires and
any other noise source. The antenna wire for the
receiver requires special attention.
Pairing
When using the receiver for the first time, the receiver must store
the ID number of the module and 'pairing' of the receiver and
module is necessar y. Pairing must be per formed when the
module or transmitter that is used is changed. When multiple
receivers are used, each receiver must go through the pairing
process at least once.
For RF-90３FH / RF-90４FH
While pressing the setup but ton,
turn the transmitter ON. (Continue to
press the button.)
Release the setup button when the
LED goes out.
Preparation is complete when the
LED is semi illuminated. (LED is
dim.)
For EX-1 KIY
Please refer to the EX-1 KIY instruction manual.
Fail-safe function
Fail-safe is when the receiver loses the radio signal of the transmitter,
and the function keeps channel 2 (throttle) in an optional position.
The configuration is usually full brake or neutral.
WARNING Please be sure to set the fail-safe.
Configuration instructions
Turn on the transmitter and the receiver and verify operation.
On the transmitter, hold the throttle to the position you would like it
to be set to. While holding the position, press the setup button on
the receiver.
Hold the setup button on the receiver until the LED light goes off
and release the button.
Off
Antenna Tube
Receiver LED illuminated again.
Fail-Safe setting is complete.
If you change the position of the fail-safe
operation, please set again.
CAUTION
We recommend to set it again even if you
modify the car engine brake linkage.
1: Prepare the transmitter or RF module for pairing mode. Each
model will differ so please refer to the manual of each model and
the figure to the left.
2: Prepare the transmitter or RF module when you are ready to pair
the KR-211FH. (If you are using an electronic speed controller in
your car, make sure you have the power connected and turned on
when pairing.
3: Hold the setup button on the KR-211FH and turn on the power.
Once the LED is lit, release the button and the LED will go off and
back on. Pair is complete.
4: Once you've completed the pairing, turn off the power to the
While pressing receiver and transmitter and verify connection by turning the
Transmitter ON
the button
system on again.
Release
LED illuminates Button
(3 seconds) Receiver is brought close to the
transmitter. While pressing the
Goes Out setup button on the receiver, the
receiver power source is turned on.
(When power is turned on, the
button is released.)
While Press Button
Open the SYSTEM Menu and open
1m
"2.4GBand".
Select "START" and press and hold
the ENTER button.
T h e p i c t u r e t o t h e l e f t w i l l b e
displayed when in the Pairing Mode.
CAUTION
About Repairs
If you request a repair, please report the fault in as much detail
as possible. This will aid in knowing the problem and parts to
be used and repair time.
When you believe you need service.
Please refer to your manual once more and please inspect.
When you do not understand something, please inquire our
service department.
When inquiring to our service department about a breakdown,
please include as much detail as possible of the contents
mentioned below about your problem.
Name of products (battery, car, transmitter & motor) used.
When breaking down, usage condition and description of breakdown
condition.
Your address, name and telephone number.
When a repair is being requested, please be sure to send the
memo which includes the above mentioned contents in as
much detail as possible.
KONDO KAGAKU CO.,LTD.
4-17-7 Higashi-Nippori,Arakawa-ku,
Tokyo Japan 116-0014
LED will go off and light
back up and you're done.
If the LED is flashing or
dim, please try to pair it
Receiver
LED
again.
Illuminated
A f t e r t u r n i n g o f f t h e
power of the transmitter
POWER ON
and the receiver once,
the transmitter ID will be
set in the receiver.
Set up Tool
●If you are having difficulties pairing, make
sure that you are not around a wireless
LAN or microwave.If you are please move
to a dif ferent location and try again.
●After pairing is complete, Please turn off
in the order of receiver transmitter.
●Please keep the distance 1m bet ween
t r a n s m i t t e r a n d r e c e i v e r w h e n y o u
pair/bind them.
Web Site :www.kopropo.co.jp
Phone:+81-3-3807-7648