Flycolor Raptor S-Tower-30A User Manual

Thank you for purchasing our product . Any Improper operation may cause personal injury damage to the product and related equipments. This high power
system for RC model can be dangerous ,we strongly recommend reading the user manual carefully and completely. We will not assume any responsibility
for any losses caused by unauthorized modifications to our product. We have the right to change the design, appearance, performance and usage
ATTENTION requirements of the product without notice.
01
Main features
● EFM8BB21F16G
MCU, pipelined 8-bit C8051 core with 50 MHz maximum operating frequency.
● Dedicated high frequency driver, makes the start more smooth.
● Two layers tower structure between 4in1 ESC and FC using quick pin connection.
●
Exposed pads for Battery and Motor wires, fast welding without additional disassembly, makes the installation faster and more convenient.
● F3 flight controller, supports PPM, PWM and SBUS remote control / receiving mode
● FC integrated OSD, also integrated 5V/1A, 12V/500mA for Image transmitter, camera, buzzer, LED and other peripheral devices ; provided
several silicone cables for connectors on FC ,and will give you an unprecedented experience for installation;
● Connect computer via USB on the flight controller, then can upgrade ESC software directly or adjusted the ESC settings directly ;
●
Built-in current meter, OSD directly display the real-time current without any additional connection;
●
BLHeli-S firmware is the next generation code, following the base BLHeli code. It designed for superior performance in multirotors, and uses hardware
generated motor pwm for smooth throttle response and silent operation.
●
Supports features to prevent sync loss. There are tuneable parameters that can make the code run well even in the most demanding situations, although default
settings will work excellently in normal operating environments.
● The code supports regular 1-2ms pulse width input, as well as Oneshot125 , Oneshot42 and Multishot . The input signal is automatically detected by the ESC upon
power up.
●
Supports Dshot150, Dshot300 and Dshot600.Dshot is digital signal, anti-interference ability is stronger, and do not need throttle calibration.
02
Specifications
Model Manufacture Model
Raptor S-Tower-20A
W4-FW020004-SX
Raptor S-Tower-30A
W4-FW030004-SX
*Raptor S-Tower is using the A-H-15 BLHeli-S firmware; Please contact Flycolor for more information.
03
Part list / Install Dimensions
Description
Item
Raptor BLS 4in1 ESC
1
Flight Controller
2
3 Nylon spacer M3*6+6
Nylon Nut M3
4
Nylon screw M3*10
5
(Not shown in figure)
For quick plug, Flight Controller additionally provide：
one 10p cable (10-pin SH1.0 terminal) for PWM or PPM connectors;
one 3p cable (4-pin SH1.0 terminal)for SBUS connector;
one 5p cable (5-pin SH1.0 terminal)for LED and Buzzer.
three 4p cables(4-pin SH1.0 ) for different brand Image Transmitters.
two 3p cables (3-pin SH1.0 )for different brand Cameras;
Attention: For these quick plug cables, please confirm the wire
sequences on your devices' connector are corresponding with the
Flight controller's before connecting. If the terminals are not fit your
devices ,please make a modified connection to fit.
04
Wiring diagram of ESC and FC receiving mode
ESC
3#Motor
V-
-
Battery V
v+
Battery
V+
1#Motor
SBUS Mode
Smart Port Pad
RSSI
GND
Image
Vin
transmitter
GND
VIDEO
ESC maximum speed is limited to 500k eRPM.
Con. Current
20A
30A
Qty.
1
1
4
8
2
8
4
3
1
4#Motor
Dual ways signal
transmission
M1 M2
2#Motor
TOP
"BOOT" for recovering firmware
Press
S.Port
PPM/PWM
GND
5V
1
2
3
4
5
6
AD1
AD2
AD2
GND
GND
12V
12V
S
S
Video
Dual ways signal transmission makes the flight more stable
.
Burst Current
BEC LiPo cells
(10S)
30A No
40A No
*All pictures are for reference only
ATTENTION
● All welding requires good welding technology, short circuit between the element
or the wire should be avoided at any time.
● Please ensure all solder joints are insulated with heat shrink where necessary.
●Please double-check the polarity is correct before power up.
G
N
D
ISP programming (OSD Debug)
User Manual
Multi-Rotor Brushless ESC
Weight
(For reference)
20g
2-4S 41.5x36x19.6mm
20g
2-4S 41.5x36x19.6mm
Install Dimensions
BOTTOM
GND
5V
5 LED
4
3
5V 5V
LED
2
5V Buzzer
Buz-
1
RX
4
SBUS
RX
TX
2
5V
5V Receiver
1
GND
SBUS
3 S
S
D
12V
2
T R T 5 12V
X X R V Camera
1
GND
Camera
ISP
Raptor S-Tower
RAPTOR
S
TOWER
*图片仅供参考，产品以实物为准
Size Typical Applications
(For reference)
130-330 Multi
170-450 Multi
36 mm
30.5 mm
41.5 mm
LED
Buzzer
12V