Download Print this page
Skyrc Toro PRO P120 Instruction Manual
Skyrc Toro PRO P120 Instruction Manual

Skyrc Toro PRO P120 Instruction Manual

1/10 scale advence racing speed controller

Advertisement

Quick Links

INSTRUCTION MANUAL
P120
120
DAYS
1/10 SCALE ADVENCE
RACING SPEED CONTROLLER
Support Both Sensor or Sensor-less Brushless Motor
PLEASE READ ALL INSTRUCTIONS BEFORE OPERATION
INTRODUCTION
Congratulations and thank you for purchasing TORO PRO High performance sensor 1/10
Scale Brushless Motor Electronic Speed Control. The TORO PRO ,1/10 scale brushless ESC
represents a latest technologies, providing all the features and robust design qualities.
SAFETY NOTE
WARNING: This is an extremely powerful brushless motor system. We strongly
recommend removing your pinion gear for your own safety and the safety of those around you
before performing calibration and programming functions with this system. Please keep your
hands, hair, cloth, clear from the gear train and wheels of an armed high performance system.
WATER & ELECTRONICS DON'T MIX!
Never allow water, moisture, or other foreign materials to get inside ESC, motor, or on the
PC Boards. Water damage will void the warranty!
NO REVERSE VOLTAGE!
Reverse battery polarity can damage ESC & void warranty. Disconnect battery immediately
if a reverse connection occurs.
DISCONNECT BATTERIES WHEN NOT IN USE
Always disconnect the battery pack from the speed control when not in use to avoid short
circuits and possible fire hazard.
TRANSMITTER ON FIRST
Turn on the transmitter first THEN turn on the speed control.
14
+Yr
1/8
INSULATE WIRES
Always insulate exposed wiring with heat shrink tubing or electrical tape to prevent short
circuits, which can damage ESC.
TIMING PRODUCES DANGEROUSLY HIGH SPEED
When Toro's electronic motor timing is enabled, the vehicle speed can be increased
dramatically. Please take extra precautions.
TIMING INCREASE ESC & MOTOR'S TEMPERATURE.
Electronic motor timing will increase the temperatures of ESC and brushless motor. Use
extreme caution when setting up and testing your application to avoid overloading
and overheating.
2-3 LIPO OR 4-8 NiMH CELLS ONLY
Never use fewer than 2 or more than 3 LIPO cells (4-8 NiMH) in the vehicle's main battery
pack. The Toro 10 handles up to 12.6 Volts Max.
BEFORE YOU BEGIN
1)Plan Speed Control Placement
Choose a location for the speed control that is protected from debris. To prevent radio
interference place the speed control as far away from the radio receiver as possible
and keep the power wires as short as possible.Select a location that has good airflow
ventilating. If the ESC gets air flow, it will run cooler; and that means, it will be
more efficient.
2)Mount Speed Control in Vehicle
Use double-sided tape to mount the speed control in vehicle(do not use CA glue).
Secure power capacitor module to chassis. You can use double-sides tape or a
tie wrap to mount power capacitor to the vehicle's chassis or shock tower. Module
can also be tie-wrapped along the power wires.
Use double-sided tape to mount the switch where it will be easy to access.Select
a position where it will not get damaged or get switched OFF during a crash or
roll-over.
3) Soldering
Cut the ESC's BLUE, YELLOW & ORANGE silicone motor power wires to the desired
length and strip about 3.2mm-6.35mm (1/8"-1/4") of insulation from the end of each
wire. "Pre-tin"the wire by heating the end and applying solder until it is thoroughly
covered.
CAUTION: By very careful not to splash yourself with hot solder.
Place the ESC's BLUE Phase 'A' motor wire onto motor's 'A' solder tab and solder.
Use soldering iron to apply heat to exposed wire; begin adding solder to tip of soldering
iron and wire. Add just enough solder to form a clean and continuous joint from the
plated area of the solder tab up onto the wire. Solder the ECS's YELLOW Phase
'B' motor wire to the motor's 'B' solder tab and Solder the ESC's ORANGE
Phase 'C' motor wire to motor's 'C' solder tab.
Ver. 1.1
2/8
Ver. 1.1

Advertisement

loading
Need help?

Need help?

Do you have a question about the Toro PRO P120 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Skyrc Toro PRO P120

  • Page 1 INSTRUCTION MANUAL INSULATE WIRES Always insulate exposed wiring with heat shrink tubing or electrical tape to prevent short circuits, which can damage ESC. TIMING PRODUCES DANGEROUSLY HIGH SPEED P120 When Toro's electronic motor timing is enabled, the vehicle speed can be increased dramatically.
  • Page 2 Red LED blinks whiles beeping, indicating it's time to push full CONNECTIONS brake. Move throttle trigger to full brake and wait few seconds, Connect motor sensor harness to ESC. Insert the 6 pin connector on the end of the ESC will blink red LED and rings 1second indicating full brake the motor's sensor wires into ESC's sensor harness socket.
  • Page 3 Programmable Features 1)Disable Question (Setting) 2)Normal(D)* 1)Reverse Lockout(D)* Note: Factory Defaults are indicated by asterisk (D)* You must answer yes or no to the setting values as they are presented by TORO PRO. " " " " When you enter programming mode the ESC will emit a sequence of beeps and LED flashes 2)50%(D)* that tell you which programming step you are in.
  • Page 4 ATV on your radio) on the throttle channel out to between 100 to 120%. Make SKYRC speed control & motor is thoroughly tested & cycled before leaving our facility and is, sure if you have a Futaba or Futaba made transmitter to have the throttle therefore, considered operational.