Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for TAIFUN GT III
Summary of Contents for TAIFUN GT III
- Page 1 Taifun® GT II /GT II Air– Bedienungsanleitung deutsch ® GT III User Manual english...
- Page 2 ® Taifun GT III rebuildable tank atomizer. Thank you for purchasing a Taifun® GT III. With this product you have purchased a high quality rebuildable tank atomizer, which has been designed exclusively for use with e-liquid. Before use it is necessary to install a coil of resistance wire (e.g. NiCr wire) and a suitable wick (e.g.
- Page 3 Please use only liquids which explicitly are intended for use in e-cigarettes. The Taifun® GT III is made of high quality materials and has been thoroughly cleaned prior to delivery. Cleaning before use is not necessary. Any visible residues are clean water and glycerine used for pretreatment of o-rings.
- Page 4 Taifun® GT III – User Manual Scope of delivery Taifun® GT III 1 x Rebuildable atomizer Taifun® GT III 1 x Info card for authenticity verification 1 x Drip Tip Taifun® GT III 1 x Sealing rings (spare parts)
- Page 5 Taifun® GT III – User Manual Attaching a coil On the base there are 2 screws, which are used to fix the wire (plus and minus pole). The screws are slightly offset so that the wire can be easily attached.
- Page 6 Taifun® GT III – User Manual Liquid Control The Liquid Control is adjusted by the Drip Tip. The Drip Tip can be adjusted by 360 °. The Liquid Control can be easily checked through the glass of the tank.
-
Page 7: Airflow Control
Taifun® GT III – User Manual Airflow Control The adjustment of the airflow is supplied via the AFC ring located on the underside of the base and has two differently sized slots. There are eleven air holes under the AFC ring in total. - Page 8 Taifun® GT III – User Manual Recucing the air channel Optional available is a conical shaped PEEK tube (3.35 x 3.55 x 6 mm) with an inside diameter of 2mm. With this tube a very strong airflow can be achieved, independent of air flow regulation.
-
Page 9: Filling The Tank
Taifun® GT III – User Manual Filling the tank To fill the Taifun® GT III, first close the liquid control. Turn the drip tip until the liquid control openings are completely closed. The liquid flow is now interrupted and you can unscrew the top cap to fill the tank. - Page 10 Taifun® GT III – User Manual Filling the tank (optional) Since the supplied drip tip has two "teeth", which are necessary for adjusting the liquid control, the liquid control can not be adjusted with other drip tips and thus can not be closed for filling.
- Page 11 Taifun® GT III – User Manual Filling the tank (optional) It is also possible to fill from tank from the bottom. To do this, place the tank upside down and unscrew the base. The tank must be held upside down during the entire filling process.
- Page 12 Taifun® GT III – User Manual Adjusting the positive pole The positive pole of the 510 connection can be adjusted to match the pole of the used device/mod. This requires a suitable screwdriver. The positive pole should only be screwed out as far as...
- Page 13 Taifun® GT III – User Manual Taifun® GT III parts spring negative pole screw glass tank countersunk head screw negative pole mount tank ring positive pole base plate AFC ring O-ring 19x1 mm (NBR 70) positive pole screw base...
- Page 14 Taifun® GT III – User Manual Taifun® GT III assembly spring positive pole base plate positive pole mount 3x spacer countersunk head screw positive pole screw isolator (PA) O-ring 5x1,5 mm Pic 1: The isolator [6] is pushed over the...
- Page 15 Taifun® GT III – User Manual Taifun® GT III assembly Pic 13: The parts 9, 10, 11 as well as 15 and Pic 14: First, put the O-ring [15] in the Pic 15: The O-ring [15] must be positioned Pic 16: Now insert the positive pole 16 are now required.
- Page 16 Taifun® GT III – User Manual Taifun® GT III assembly Pic 29: Pic 30: Now the base should look like this. Pic 31: The two O-rings [23] are installed in Pic 32: The O-rings [23] should now be The deck [16] and the base [13] are now the recesses at the upper end of the seated, as on this pic..
- Page 17 Taifun® GT III – User Manual Taifun® GT III assembly Pic 45: Attach the O-ring [25] on the top cap Pic 46: In the top cap [24] there is a Pic 46: The top cap [24] can now be Pic 47: Top cap [24], tank ring [20] and tank [24].
- Page 18 Taifun® GT III – User Manual Coil example The two screws are loosened slightly, The wire is placed behind the winding Now guide the wire from bottom to Repeat this until you have the desired in order to fix the wire.
- Page 19 Taifun® GT III – User Manual Coil example Viewed from above, the winding Now a broad strand cotton is needed. The cotton is tipped on one side and The cotton can then be shortened. On should now be uniformly and passed through the coil.
- Page 20 Taifun® GT III – User Manual SMOKERSTORE ELECTRONIC VAPING PRODUCTS SmokerStore GmbH www.smokerstore.de...
Need help?
Do you have a question about the GT III and is the answer not in the manual?
Questions and answers