Do you have a question about the FBT-8800 and is the answer not in the manual?
Questions and answers
dave charles
July 14, 2025
i have a full boar FBT-8800 RADIAL CUTTER,800 watts,the pump not working(no water on blade) it says remove screws on filter cover and clean,where is the filter to clean,i cant see anything that looks like a filter,0284634791
Page 1
KNOW YOUR PRODUCT RADIAL TILE CUTTING MACHINE • 800W INDUCTION MOTOR • 520MM CUTTING LENGTH • 0°-45° BLADE TILT • DETACHABLE LASER INSTRUCTION MANUAL WARNING: Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference.
TABLE OF CONTENTS SPECIFICATIONS............Page 02 KNOW YOUR PRODUCT........... Page 02 INTRODUCTION............Page 05 SAFETY INSTRUCTIONS........... Page 05 BEFORE USING FOR THE FIRST TIME...... Page 11 ASSEMBLY..............Page 11 OPERATION............... Page 12 MAINTENANCE............Page 16 DESCRIPTION OF SYMBOLS........Page 18 CONTENTS..............
The electric motor has been designed for 230V and 240V only. Always check that the power supply corresponds to the voltage on the rating plate. Note: The supply of 230V and 240V on Full Boar tools are interchangeable for Australia and New Zealand.
Page 6
GENERAL POWER TOOL SAFETY WARNINGS WARNING! Read all safety warnings and instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. The term “Power Tool” in all of the warnings listed below refers to your mains operated (corded) power tool or battery operated (cordless) power tool.
Page 7
GENERAL POWER TOOL SAFETY WARNINGS (cont.) d. Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. e. Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
Page 8
TILE CUTTING MACHINE SAFETY WARNINGS IMPORTANT! When using the equipment, a few safety precautions must be observed to avoid injuries and damage. Please read the complete operating manual with due care. Keep this manual in a safe place so that the information is available at all times.
Page 9
TILE CUTTING MACHINE WARNINGS (cont.) • This tile cutting machine is suitable only for household use. • Deceleration time of the cutting disc - After switching off the machine, the cutting disc needs 40 seconds before coming to a standstill. Wait until the cutting disc has stopped completely, then pull the power plug out of the socket outlet and, if necessary, only then touch the machine’s rotating components.
Page 10
Do not look into the beam! Laser class 2 The light/laser radiation used in the Full Boar Radial Tile Cutting Machine FBT-8800 laser is lass 2 with maximum 1mW and 650nm wavelengths. These lasers do not normally present an optical hazard, although staring at the beam may cause flash blindness.
BEFORE USING FOR THE FIRST TIME • The machine must be set up so that it stands firmly, i.e. it must be securely screwed to a work bench, the base frame supplied, or similar. • All covers and safety devices must be correctly attached before the machine is used for the first time.
OPERATION This tile cutting machine must be used with a residual current device with a rated residual current of 30 mA or less. ON/OFF switch 1. To switch ON, press the “I” on the ON/OFF switch (16) (Fig. 8). 2. Before you begin cutting, wait until the cutting disc (2) has reached maximum speed and the water pump (13) has started supplying the cutting disc (2) with water.
Page 13
OPERATION (cont.) Straight Cutting 1. Loosen the mitre angle knob (11) on the angle gauge (5) (Fig. 10). 2. Set the angle gauge (5) to 0° and retighten the mitre angle knob (11) (Fig. 11). 3. Loosen the knurled screws (23) and use the scale on the rail fence (6) to accurately position the angle gauge.
Page 14
OPERATION (cont.) 45° Diagonal cut 1. Set the angle gauge (5) to 45° (Fig. 17). Fig. 17 2. Cut as described in Straight Cutting, from point 3 onwards. 45° Lengthwise cut Fig. 18 1. Loosen the bevel angle knobs (10) on either side of the unit (Fig.
Page 15
OPERATION (cont.) Operating the laser (28) Batteries (supplied) must first be inserted into the laser unit. Refer page 16 “Replacing the battery on the laser” Stationary operation (Fig. 21) 1. To switch ON: Move the ON/OFF switch (26) to the “I” position. 2.
MAINTENANCE IMPORTANT! Before cleaning your tile cutting machine or carrying out any maintenance procedure, make sure that the motor is off and the tile cutting machine disconnected from the power supply to prevent accidental starting. Changing the cutting disc (2) 1.
Page 17
MAINTENANCE Cleaning • Keep all safety devices, air vents and the motor housing free of dirt and dust as far as possible. Wipe the equipment with a clean cloth or blow it with compressed air at low pressure. • We recommend that you clean the device immediately each time you have finished using it.
DESCRIPTION OF SYMBOLS min¯¹ IP54 Ingress protection from water Read instruction manual Important! Risk of injury Wear gloves Wear eye protection Wear hearing protection Segmented diamond cutting wheels must not be used CARING FOR THE ENVIRONMENT Power tools that are no longer usable should not be disposed of with household waste but in an environmentally friendly way.
CONTENTS Radial Tile Cutting Machine Base frame Frame legs x 4 Hex screws and spring washers for the frame legs x 4 Trough Trough fixtures and screws x 2 Hex key Wrench x 2 AAA Batteries x 2 Instruction manual Distributed by: Ozito Industries Pty Ltd AUSTRALIA (Head Office)
WARRANTY YOUR WARRANTY FORM SHOULD BE RETAINED BY YOU AT ALL TIMES. IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY YOU MUST RETURN THE PRODUCT TO YOUR NEAREST BUNNINGS WAREHOUSE (see www.bunnings.com.au or www.bunnings.co.nz for store locations) WITH YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO RETURNING YOUR PRODUCT FOR WARRANTY PLEASE TELEPHONE OUR CUSTOMER SERVICE HELPLINE: Australia 1800 069 486 New Zealand 0508 069 486...
Need help?
Do you have a question about the FBT-8800 and is the answer not in the manual?
Questions and answers
i have a full boar FBT-8800 RADIAL CUTTER,800 watts,the pump not working(no water on blade) it says remove screws on filter cover and clean,where is the filter to clean,i cant see anything that looks like a filter,0284634791