Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Riger DB108-WL
- Page 1 DB108-WL WIRELESS ADSL MODEM USER’S MANUAL (V3.0)
-
Page 2: Table Of Contents
...............................16 5 OTHER FUNCTIONS AND CONFIGURATION ..................19 RIDGE FILTERING ................................19 5.2 STATUS BAR..................................19 CONFIGURATION OF DB108-WL’S IP ADDRESS AND PASSWORD ............20 6 SOFTWARE UPGRADE..........................22 7 RESET TO DEFAULT SETTING ......................... 22 8 SPECIFICATIONS ............................22 A TROUBLESHOOTING..........................23 B CONNECTION OF SPLITTER ........................ -
Page 3: Overview
1Mbps and download speed up to 8 Mbps. ADSL is an ideal device for broadband access. But the ADSL users are also limited by the wire and can’t move freely. DB108-WL wireless ADSL Modem is a new device that integrates WLAN and ADSL functions. Users can slip the leash to visit Internet even in moving as long as they install WLAN cards into their computers. -
Page 4: Protocols
Usb Interface For Modem connection on program upgrade or alternative internet access. Line Interface Connect to telephone. Reset button: Reset the configuration to default 1.3 PROTOCOLS DB108-WL ADSL Modem supports ADSL protocols below: PPPoA PPP over ATM LLC encapsulation or VCMUX encapsulation (RFC2364) -
Page 5: Hardware Installation And Basic Configuration
DB108-WL wireless ADSL MODEM manual 2. HARDWARE INSTALLATION AND BASIC SOFTWARE CONFIGURATION 2.1 SYSTEM REQUIREMENT The computer used must be equipped with a network card or WLAN card 2.2 HARDWARE INSTALLATION 2.2.1 BASIC CONNECTTION Figure 2.1 For using the Splitter to surf on the Internet and to make phone calls simultaneously, please refer to Appendix B: SPLITTER CONNECTION. -
Page 6: Computer Configuration
DB108-WL wireless ADSL MODEM manual Before the installation starts, please confirm information below or consult ADSL service provider. Table 2.1 shows all the information needed to configure according to different protocols. Table 2.1 VIRTUAL DIAL PRIVATE LINE MODE MODE PROTOCOL... - Page 7 DB108-WL wireless ADSL MODEM manual Table 2.2 PAGE ITEM PPPoE PPPoA 1483 1483ROUTING 1577 BRIDGE PRIVATE CONNECT LINE √ √ √ √ √ √ √ √ √ √ STATIC IP √ √ ADDRESS SUBNET MASK √ √ ENCAPSULATION PPPoE PPPoA...
- Page 8 DB108-WL wireless ADSL MODEM manual Figure 2.3 4. Click “Submit” button to save the parameters, then ADSL will restart automatically and the MODEM will run on the set parameters. 2.3.5 Wireless work mode configuration Click the “Wireless”. Wireless configuration page will appear as figure2.4.
-
Page 9: Default Configuration
Then click “Save setting” to enter the “save configuration” page as Figure2.3 and click “Submit” button to save the parameters. The modem will restart automatically with the new parameters. 2.3.6 DEFAULT CONFIGURATION DB108-WL have pre-configuration the follow VCI/VPI Table 1 PVC 0... - Page 10 DB108-WL wireless ADSL MODEM manual Figure 2.5 - 9 -...
-
Page 11: Protocol Configuration
DB108-WL wireless ADSL MODEM manual 3. PROTOCOL CONFIGURATION Different protocols should be set in “WAN”,“LAN”,“NAT”and “DNS” columns in the configuration page. Click on the relevant icons to enter the right page accordingly. The detail is listed below. 3.1 RFC1483 BRIDGE CONFIGURATION 1. - Page 12 DB108-WL wireless ADSL MODEM manual Figure 3.2 DNS SETTINGS Keep the default configuration. Click “Save Settings” button in configure item as Figure 2.3. Click “Submit” to save all the above settings. Then modem will restart automatically and run under new parameters 3.2 STATIC ROUTING CONFIGURATION RFC1483ROUTING/RFC1577CONFIGURATION...
-
Page 13: E Configuration
DB108-WL wireless ADSL MODEM manual Figure 3.3 LAN SETTINGS Keep the configuration as default NAT SETTINGS Select “Dynamic NAPT” or “NAPT” as Figure 3.4 , then click “Submit” to save the settings Figure 3.4 DNS SETTINGS - 12 -... - Page 14 Install “dialing software” such as Enternet300, WinPoet and RasPPPoE. For more detail consult with the DSL provider. Use the” dialing software” to dial up. Internal virtual Dial-up function in DB108-WL WAN SETTING Set “Enabled” as“Yes” Set the value of VPI, VCI (For example VPI=0,VCI=32)
- Page 15 DB108-WL wireless ADSL MODEM manual For PPPoE select “PPPoE LLC” or“PPPoE VC MUX” in “ENCAPSULATION ” (some values need to be provided by DSL provider ) ; For PPPoA select “PPPoA LLC” or“PPPoA VC MUX” in “ENCAPSULATION” (some value need to be provided by DSL provider ) Select “Disabled”...
- Page 16 DB108-WL wireless ADSL MODEM manual Set DNS Proxy selection at “Use user configured DNS servers only”, at Preferred DNS Server (202.96.209.133) and“Alternate DNS server”enter (202.96.209.5) shown as Figure 3.5 then click “Submit” to save the settings. Click “Save Settings” in configuration. Click “Submit” to save all the above settings. Then ADSL will restart automatically and run under new parameters.
-
Page 17: Tcp/Ip Protocol Configuration
4. Application of DHCP and DNS Features Not only can the DB108-WL be used as an ADSL Modem, it also has routing, DHCP and DNS features, which are especially applicable for small LAN such as cyber cafés and/or small companies. - Page 18 DNS server”enter (202.96.209.5) as shown in Figure 3.5 then click “Submit” to save the settings. 4. Click “Save Settings” button in configuration. Click “Submit” to save all the above settings. Then ADSL will restart automatically and run under new parameters. After configuration, restart DB108-WL first and then restart computers in LAN - 17 -...
-
Page 19: Other Functions And Configuration
Figure 5.1 2. Users can modify or delete the MAC addresses that have been input. Just as Figure 5.2. Figure 5.2 5 2 STATUS The working status of DB108-WL can be monitored over through the items of status. - 18 -... - Page 20 DB108-WL wireless ADSL MODEM manual ADSL As shown in figure 5.3, the line status of ADSL, working time, connection speed, signal noise ratio and the line attenuation can be obtained from this page. Figure 5.3 SYSTEM LOG The system log page is shown in figure 5.4. You can examine the working status of system or save the system log for later diagnostic.
-
Page 21: Configuration Of Db108-Wl's Ip Address And Password
As a network device, DB108-WL ADSL Modem has its own IP address and MAC address. The factory sets the DB108-WL at a default IP address of 192.168.1.1 and subnet mask of 255.255.255.0. The user can configure these addresses through the “LAN” on “Configuration”... -
Page 22: Software Upgrade
DB108-WL wireless ADSL MODEM manual 6.SOFTWARE UPGRADE DB108-WL supports software upgrade from network. To get detailed information, please ask the associated manufacturer or agents. 7. RESET TO DEFAULT SETTING If you can’t log on configuration page (for example: you forget the password),you can use this method to reset the ADSL MODEM to the default configuration Then you can log on with the default username and password Put the Reset button down shown as Figure 7.1 and release it can restart the modem to default settings. -
Page 23: A Troubleshooting
DB108-WL wireless ADSL MODEM manual Electromagnetic: in accordance with FCC, ETSI and CISPR standard IEEE 802.11b standard. 8 5 ENVIRONMENT REQUIREMENTS Temperature: 5°C 40°C(41F 104F) Relative humidity:0% 95% Electromagnetic disturbance FCC PART15&68 A. Troubleshooting Phenomena Solution Make sure the connection of power supply is correct. - Page 24 DB108-WL wireless ADSL MODEM manual Make sure the problems list above are all eliminated; Make sure the WLAN card in computer works well. Check the wireless mode is “infrastructure”; Make sure that “wireless” is shown on the configuration page of the modem. Otherwise there should be hardware error for the modem.
- Page 25 DB108-WL wireless ADSL MODEM manual B. SPLITTER CONNECTION Splitter Connection Firstly, use a telephone cord to connect the LINE port of Splitter and the RJ-11 port on the wall. Then use another telephone cord to connect the ADSL port of Splitter and the LINE port of ADSL Modem. Finally, use another telephone cord to connect the telephone set and the TEL port of the Splitter.
-
Page 26: C Shipping List
DB108-WL wireless ADSL MODEM manual C. SHIPPING LIST Check the list of device as the follow, if there is missed you must contact franchiser - 25 -... - Page 27 DB108-WL wireless ADSL MODEM manual Please use the factory- recommended power supply. Caution: To assure continued compliance, (example – use only shielded interface cables when connecting to computer or peripheral devices). Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Need help?
Do you have a question about the DB108-WL and is the answer not in the manual?
Questions and answers