Sloan 110 Installation Instructions Manual

Sloan 110 Installation Instructions Manual

Exposed gem 2 piston type water closet and urinal flushometers

Advertisement

Quick Links

PISTON TYPE WATER CLOSET AND URINAL FLUSHOMETERS
Closet Flushometer for
1½" Top Spud
MODELS 110/111, 115 & 136
Made in the U.S.A.
Sloan Valve Company warrants its Gem•2
perform the service for which they are intended in a thoroughly reliable and efficient manner when properly installed and serviced, for a period of three years (1 year
for special finishes) from date of purchase. During this period, Sloan Valve Company will, at its option, repair or replace any part or parts which prove to be thus
defective if returned to Sloan Valve Company, at customer's cost, and this shall be the sole remedy available under this warranty. No claims will be allowed for labor,
transportation or other incidental costs. This warranty extends only to persons or organizations who purchase Sloan Valve Company's products directly from Sloan Valve
Company for purpose of resale.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. IN NO EVENT IS SLOAN VALVE COMPANY
RESPONSIBLE FOR ANY CONSEQUENTIAL DAMAGES OF ANY MEASURE WHATSOEVER.
INSTALLATION INSTRUCTIONS FOR EXPOSED GEM•2
Urinal Flushometer for
Urinal Flushometer for
®
Flushometers to be made of first class materials, free from defects of material or workmanship under normal use and to
1¼" Top Spud
MODEL 180
¾" Top Spud
MODEL 186

LIMITED WARRANTY

Code No. 0816178
Rev. 2 (04/07)
®
Closet Flushometer for
1½" Back Spud
MODELS 120, 121, 122 & 137

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 110 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Sloan 110

  • Page 1 (1 year for special finishes) from date of purchase. During this period, Sloan Valve Company will, at its option, repair or replace any part or parts which prove to be thus defective if returned to Sloan Valve Company, at customer’s cost, and this shall be the sole remedy available under this warranty.
  • Page 2 VALVE ROUGH-IN MODELS 110/111, 115 MODELS 120, 121, 122 MODEL 137 MODEL 136 MODEL 186 MODEL 180 NOTE: Requires 1” I.P .S. (DN 25 mm) Supply. NOTES: • WHEN MOUNTED ON AN ADA ACCESSIBLE BOWL, THE ROUGH-IN TO THE SUPPLY INLET SHOULD BE NO HIGHER THAN 37½”...
  • Page 3 If you have questions about how to install your Gem•2 Flushometer, • Straight blade screwdriver consult your local Sloan Representative or call Sloan Installation • Sloan A-50 Super-Wrench™, Sloan A-109 Plier Wrench or smooth Engineering Department at: jawed spud wrench...
  • Page 4 CONNECTION SPUD FLANGE SPUD COUPLING SPUD COUPLING NOTE NYLON SLIP NYLON SLIP Maximum adjustment of the Sloan Adjustable Tailpiece is GASKET GASKET 1/2" (13 mm) IN or OUT from the standard 4-3/4" (121 mm) RUBBER NYLON RUBBER (centerline of Flushometer to centerline of Control Stop).
  • Page 5 Seal will easily slide onto the Bushing if it is wet. proper Closet Piston. B. Handle gasket has been omitted. Replace Sloan Handle Assembly (G-143-A). C. Low Consumption Flushometer installed on a non-Low Consumption fixture. C. Valve Handle Bushing is worn. Replace Sloan Handle Assembly (G-143-A).
  • Page 6: Parts List

    For a complete listing of GEM•2 Flushometer Valve Components and Repair Kits, refer to the Maintenance Guide or consult your nearest plumbing wholesaler. For optimum water conservation and Flushometer performance, use only Genuine Sloan Parts. NOTICE: The information contained in this document is subject to change without notice.

This manual is also suitable for:

111115136180186121 ... Show all

Table of Contents