1. Manuals
  2. Brands
  3. HIKVISION Manuals
  4. Security Camera
  5. 2T series
  6. Quick start manual

HIKVISION 2T series Quick Start Manual

Network bullet camera
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Network Bullet Camera
Quick Start Guide
0

Advertisement

Table of Contents
loading

Related Manuals for HIKVISION 2T series

Summary of Contents for HIKVISION 2T series

  • Page 1 Network Bullet Camera Quick Start Guide...

  • Page 2: Regulatory Information

    Network Bullet Camera·Quick Start Guide About this Manual This Manual is applicable to 2Txx Network Camera. The Manual includes instructions for using and managing the product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons.
  • Page 3 Network Bullet Camera·Quick Start Guide Please take attention that changes or modification not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.

  • Page 4: Safety Instruction

    Network Bullet Camera·Quick Start Guide EU Conformity Statement This product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with the applicable harmonized European standards listed under the EMC Directive 2014/30/EU, the RoHS Directive 2011/65/EU 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted...
  • Page 5 Network Bullet Camera·Quick Start Guide These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into “Warnings” and “Cautions” Warnings: Serious injury or death may occur if any of the warnings are neglected.
  • Page 6 Network Bullet Camera·Quick Start Guide ● Please make sure that the plug is firmly connected to the power socket. When the product is mounted on wall or ceiling, the device shall be firmly fixed. ● If smoke, odor or noise rise from the device, turn off the power at once and unplug the power cable, and then please contact the service center.
  • Page 7 Network Bullet Camera·Quick Start Guide camera model has an “H” in its suffix), dusty or damp locations, and do not expose it to high electromagnetic radiation. ● To avoid heat accumulation, good ventilation is required for operating environment. ● Keep the camera away from liquid while in use. ●...

  • Page 8: Table Of Contents

    Network Bullet Camera·Quick Start Guide Table of Contents 1 Appearance Description ..............8 Type I Bullet Camera ............8 Type II Bullet Camera ............9 Type III Bullet Camera ........... 10 2 Installation ..................12 Memory Card Installation ..........12 Direct Mounting ............

  • Page 9: Appearance Description

    Network Bullet Camera·Quick Start Guide 1 Appearance Description 2T camera series has three appearance types. Type I supports no memory card. Type II and Type III support memory card function, but the positons of memory card slots on camera are different. Type I Bullet Camera Figure 1-1 Overview of Type I Table 1-1 Description of Type I...

  • Page 10: Type Ii Bullet Camera

    Network Bullet Camera·Quick Start Guide Type II Bullet Camera Figure 1-2 Overview of Type II Table 1-2 Description of Type II Description Description Lens Network Interface (PoE) Sun Shield Memory Card Slot Power Interface Reset Button...

  • Page 11: Type Iii Bullet Camera

    Network Bullet Camera·Quick Start Guide Note: Use reset button to reset the camera: Press and hold the reset button about 10s when the camera is powering on or rebooting to restore the default settings, including the user name, password, IP address, port No., etc.
  • Page 12 Network Bullet Camera·Quick Start Guide Description Description Power Interface Reset Button Network Interface (PoE) Note: Use reset button to reset the camera: Press and hold the reset button about 10s when the camera is powering on or rebooting to restore the default settings, including the user name, password, IP address, port No., etc.

  • Page 13: Installation

    Network Bullet Camera·Quick Start Guide 2 Installation Before you start: ● Make sure the device in the package is in good condition and all the assembly parts are included. ● The standard power supply is 12 VDC, please make sure your power supply matches with your camera.
  • Page 14 Network Bullet Camera·Quick Start Guide Expose Memory Card Slot 2. Insert the memory card. Type II Memory Card Type III Memory Card Slot Insert Memory Card 3. (Optional) To unmount the memory card, push to get it ejected.

  • Page 15: Direct Mounting

    Network Bullet Camera·Quick Start Guide 4. Screw the cover back to the camera when installation is finished. Direct Mounting Steps: 1. Drill 4 screw holes (hole 1 on drill template) and the cable hole in the ceiling/wall. Ceiling Mounting Cable Hole 1:Screw Hole for 2:Screw Hole for Bracket...
  • Page 16 Network Bullet Camera·Quick Start Guide Figure 2-4 Install the Camera 3. Adjust the view angle. 1). Loosen No.1 lock screw to adjust the tilt angle [0 ° to 100°]. 2). Loosen No.2 lock screw to adjust the pan angle [0° to 360°]. 3).

  • Page 17: Mounting With A Junction Box

    Network Bullet Camera·Quick Start Guide Figure 2-6 Supplied Wrench 4. (Optional) Install the water-proof jacket for network interface. Refer to Section 2.5 Network Cable Water-proof Jacket Installation (Optional). Note: It is recommended to adopt the water-proof jacket (supplied) for the network interface, especially when the camera is installed outdoor.
  • Page 18 Network Bullet Camera·Quick Start Guide Figure 2-7 Dimension of Junction Box Steps: 1. Paste the drill template to desired mounting place. Drill the screw hole and cable hole according to the supplied drill template (shown as Figure 2-3). 2. Align the screw holes of the junction box to the drill template, and fix the junction box to the wall with screws.

  • Page 19: Mounting With A Gang Box

    Network Bullet Camera·Quick Start Guide Junction Box Drill Template Safety Rope Installation with a Junction Box Mounting with a Gang Box Before You Start: An adapter plate should be purchased separately if you mount the camera to a gang box. Steps: 1.
  • Page 20 Network Bullet Camera·Quick Start Guide Adapter Plate Figure 2-9 Installation with a Gang Box Network Cable Water-proof Jacket Installation (Optional) Purpose: If the camera is installed outdoor, you can adapt the water-proof accessory for the network cable after the camera is secured on the installation surface.
  • Page 21 Network Bullet Camera·Quick Start Guide Table 2-1 Components Components Camera’s Network Interface Socket O-Type Gasket Network Plug Waterproof Endcap Waterproof Rubber Gasket Lock Nut Network Cable from Router/Switch Steps: Feed the plugless network cable ⑦ through the lock nut ⑥, waterproof rubber gasket ⑤...
  • Page 22 Network Bullet Camera·Quick Start Guide Insert the water-proof rubber gasket ⑤ into the waterproof endcap ④, and secure lock nut ⑥ with the water-proof endcap ④. Align the snap on the water-proof endcap ④ with the notch on the camera’s network interface socket ①, and then secure the water-proof endcap ④...

  • Page 23: Setting The Network Camera Over The Lan

    Network Bullet Camera·Quick Start Guide 3 Setting the Network Camera over the Note: You shall acknowledge that the use of the product with Internet access might be under network security risks. For avoidance of any network attacks and information leakage, please strengthen your own protection.

  • Page 24: Activating The Camera

    Network Bullet Camera·Quick Start Guide Activating the Camera You are required to activate the camera first by setting a strong password for it before you can use the camera. Activation via Web Browser, Activation via SADP, and Activation via Client Software are all supported. We will take activation via SADP software and Activation via Web Browser as examples to introduce the camera activation.

  • Page 25: Activation Via Sadp Software

    Network Bullet Camera·Quick Start Guide Activation Interface(Web) 3. Create a password and input the password into the password field. STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
  • Page 26 Network Bullet Camera·Quick Start Guide Get the SADP software from the supplied disk or the official website, and install the SADP according to the prompts. Follow the steps to activate the camera, please refer to the User Manual of Network Camera for other two activation methods.

  • Page 27: Modifying The Ip Address

    Network Bullet Camera·Quick Start Guide STRONG PASSWORD RECOMMENDED– We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product.
  • Page 28 Network Bullet Camera·Quick Start Guide Steps: 1. Run the SADP software. 2. Select an activate device. 3. Change the device IP address to the same subnet with your computer by either modifying the IP address manually or checking the checkbox of Enable DHCP. Note: You can enable the Guarding Vision service for the device during activation.

  • Page 29: Accessing Via Web Browser

    Network Bullet Camera·Quick Start Guide 4 Accessing via Web Browser System Requirement: Operating System: Microsoft Windows XP SP1 and above version CPU: 2.0 GHz or higher RAM: 1G or higher Display: 1024×768 resolution or higher Web Browser: Internet Explorer 8.0 and above version, Apple Safari 5.0.2 and above version, Mozilla Firefox 5.0 and above version and Google Chrome 18 and above version Steps:...
  • Page 30 Network Bullet Camera·Quick Start Guide 4. Click Login. Login Interface 5. Install the plug-in before viewing the live video and managing the camera. Please follow the installation prompts to install the plug-in. Note: You may have to close the web browser to finish the installation of the plug-in.

  • Page 31: Operating Via Guarding Vision App

    Network Bullet Camera·Quick Start Guide 5 Operating via Guarding Vision App Purpose: Guarding Vision is an application for mobile devices. With the App, you can view live image of the camera, receive alarm notification and so on. Note: Guarding Vision service is not supported by certain camera models. Enable Guarding Vision Service on Camera Purpose: Guarding Vision service should be enabled on your camera before...

  • Page 32: Enable Guarding Vision Service Via Web Browser

    Network Bullet Camera·Quick Start Guide “Privacy Policy” Service” Verification Code Setting (SADP) Note: The verification code is required when you add the camera to Guarding Vision app. 3. Click and read "Terms of Service" and "Privacy Policy". 4. Confirm the settings. Enable Guarding Vision Service via Web Browser Before you start: You need to activate the camera before enabling the service.
  • Page 33 Network Bullet Camera·Quick Start Guide Steps: 1. Access the camera through web browser. Refer to Chapter 4. 2. Enter platform access configuration interface: Configuration > Network > Advanced Settings > Platform Access Guarding Vision dev.guardingvision.com Platform Access Configuration (Web) 3. Select Platform Access Mode as Guarding Vision. 4.

  • Page 34: Guarding Vision Setup

    Network Bullet Camera·Quick Start Guide Guarding Vision Setup Steps: 1. Download and install the Guarding Vision app by searching “Guarding Vision” in App Store or Google Play 2. Launch the app and register for a Guarding Vision user account. 3. Log in Guarding Vision app after registration. Adding Camera to Guarding Vision Before you start: You need to enable the Guarding Vision service on camera before...
  • Page 35 Network Bullet Camera·Quick Start Guide You can find the QR code on the camera or on the cover of the Quick Start Guide of the camera in the package. Figure 5-4 Scan QR Code Note: If the QR code is missing or too blur to be recognized, you can also add the camera by tapping the icon and inputting the camera's serial number.

  • Page 36: Initializing The Memory Card

    Network Bullet Camera·Quick Start Guide Initializing the Memory Card Steps: Check the memory card status by tapping on the Storage Status in the Device Settings interface. If the memory card status displays as Uninitialized, tap to initialize it. The status will then change to Normal. You can then start recording any event triggered video in the camera such as motion detection.

Table of Contents