Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Air Live SI-102
Summary of Contents for Air Live SI-102
-
Page 1: User Manual
SI-102 PIR Motion Sensor User Manual... - Page 2 This product contains some codes from GPL. In compliance with GPL agreement, AirLive will publish the GPL codes on our website. Please go to www.airlive.com and go to the "Support->GPL" menu to download source code. All Trademarks are properties of their respective holders. AirLive SI-102 User Manual...
- Page 3 When replacing old appliances with new once, the retailer is legally obligated to take back your old appliance for disposal at least for free of charge. AirLive SI-102 User Manual...
-
Page 4: Table Of Contents
1.5 Security Network ................4 1.6 Operation Mode ................. 5 1.7 Choosing a Suitable Location ............5 1.8 Battery Installation ................5 1.9 Z-Wave Configuration Settings ............7 1.10 Z-Wave Supported Command Class ..........7 1.11 Specifications ................... 9 AirLive SI-102 User Manual... -
Page 5: Overview
The technology uses a low-power RF radio embedded or retrofitted into home electronics devices and systems, such as lighting, home access control, entertainment systems and household appliances. The motion sensor SI-102 has PIR function, based on Z-Wave technology. This device is a Security Enabled Z-Wave Plus Product. Z-Wave... -
Page 6: Adding To Remove From Z-Wave Tm Network
After the device adding to the network, it will wake-up once per day in default. When it wake-up it will broadcast the “Wake Up Notification” message to the network, and wake-up 10 seconds for receive the setting commands. AirLive SI-102 User Manual... -
Page 7: Z-Wave Tm Message Report
Beside the event triggered could report message, the device also support the timing unsolicited report of the status. Battery level report: Every 6 hours report once in default. It could be changed by setting the configuration NO. 10. AirLive SI-102 User Manual... -
Page 8: Power Up Procedure
In the security mode, the follow commands need using Security CC wrapped to communicate, otherwise it will not response. Note: A “Security Enabled Z-Wave Controller” must be used in order to fully utilize this function. AirLive SI-102 User Manual... -
Page 9: Operation Mode
Don't let the device facing the source of heat. For instance the heater or the air-condition. 1.8 Battery Installation When the device reports the low battery message, users should replace the battery. The battery type is CR123A, 3.0V. AirLive SI-102 User Manual... - Page 10 1. Overview AirLive SI-102 User Manual...
-
Page 11: Z-Wave Configuration Settings
6 (*) Mult- Sensor Multisensor function switch. Using bit to control. Function Caution: The range is from 0x00~0xFF using Switch hexadecimal notation. Bit0: Reserve. Bit1: Reserve. Bit2: Reserve. AirLive SI-102 User Manual... - Page 12 Detect Interval detected, setting the re-detect time. 8 seconds Time per tick, default tick is 3 (24 seconds). Setting the suitable value to prevent received the trigger signal too frequently. Also can save the battery energy. AirLive SI-102 User Manual...
-
Page 13: Specifications
Power by CR123A lithium battery. Signal (Frequency): 868.40 MHz, 869.85 MHz(EU), 908.40 MHz, 916.00 MHz(US), 922~927 MHz(JP/TW), 921.40 MHz, 919.80 MHz(ANZ), 869.00 MHz(RU), 865.20 MHz(IN), 916.00 MHz(IL), Range: Minimum 40 meters indoor, 100 meters outdoor line of sight. AirLive SI-102 User Manual... - Page 14 RF Maximum Power: +5dBm Operating Temperature: -10oC ~ 40oC For indoor use only. Specifications subject to change without notice due to continuing product improvement. OvisLink Corp., http://www.airlive.com/ TEL: +886 2 2218 6888 FAX: +886 2 2918 6988 AirLive SI-102 User Manual...
Need help?
Do you have a question about the SI-102 and is the answer not in the manual?
Questions and answers