Philips CED1700 Quick Start Manual

Register your product and get support at
CED1700
www.philips.com/welcome
1
EN Quick Start Guide
English
Install the car audio
These instructions are for a typical installation.
However, if your car has different requirements,
make the corresponding adjustment. If you have
any questions regarding installation kits, consult
your Philips car audio dealer.
Caution
• This unit is designed for negative ground
(earth) 12 V DC operation only.
Always install this unit in the car dashboard.
•
Other locations can be dangerous as the
rear of the unit heats up during use.
• To avoid short-circuit: before you connect,
ensure that the ignition is off.
• Ensure that you connect the yellow and red
power supply leads after all other leads are
connected.
• Ensure that all loose leads are insulated with
electrical tape.
• Ensure that the leads do not get caught
under screws orin parts that will move (e.g.
seat rail).
• Ensure that all ground (earth) leads are run
to a common ground (earth) point.
• Use only the supplied mounting hardware
for a safe and secure installation.
• Improper fuses can cause damage or fire.
When you need to change the fuse, consult
a professional.
Connect wires
Caution
• Ensure that all loose leads are insulated with
electrical tape.
1
Check the car's wiring carefully, then
connect them to the supplied ISO wires.
© 2010 Koninklijke Philips Electronics N.V.
Connector Connect to
All rights reserved.
Document order number: CED1700_00_QSG_V1.0
b
a
1
5
2
3
4
1 Yellow wire The +12V car battery which Connector/ Connect to/with
is live at all times. Obeject
2 Blue wire The electric antenna control 1 Pink wire Extension wire
lead or power supply lead of
2 2.5m extension Parking brake (-)
the antenna booster
wire(Not
If there is no electric antenna
included)
or antenna booster, or it is
3 Brake switch
manually operated telescopic
4 Ground
antenna, it is not necessary
to connect this lead. 5 ISO wires Connected in step 1
above.
3 Black wire A metal surface of the car
First connect the black 6 Grey wire Rear line out Left/
ground (earth) lead, then Right
connect the yellow and red
7 Black wire Front line out Left/
power supply leads.
Right
4 Red wire The +12V power terminal
8 Blue cable Subwoofer
which is live in the
9 Red cable Aux Right
accessory (ACC) position of
10 White cable Aux Left
the ignition switch
If there is no accessory 11 Yellow cable Video in
position, connect to the
12 Yellow cable Camera in
+12V car battery terminal
13 Yellow cable Video out 1
that is always live. Be sure
14 Yellow cable Video out 2
to connect the black ground
(earth) lead to a metal 15 Purple wire Reverse camera (B+)
surface of the car first.
16 Gearbox switch
5 Green and Left speaker (Rear)
17 Reverse gear Back lamp lead +
green/black
signal
wires
6 White and Left speaker (Front)
white/black
Mount in the dashboard 2
wires
7 Gray and Right speaker (Front)
Note
gray/black
wires • Check wire connection before you mount
the unit into a car.
8 Purple and Right speaker (Rear)
purple/black • If preset radio stations are lost when the
1
wires ignition key is turned OFF and then back
ON, reconnect the red leads crosswise to
2
Connect the other end of the supplied
the yellow ones.
standard connector to the car audio
1
system. b If the car does not have an on-board drive
or navigation computer, disconnect the
negative terminal of the car battery.
2
Ensure that car dashboard opening is within
a
these measurements: a
3
Slide the unit into the dashboard until a
click sound is heard. b
2
3
6 7
8 9 0 ! " § $ %
/ &
P
R
N
D
2
L
»
4
Attach the trim plate. c
5
Reconnect the negative terminal of the car
battery.
Turn on
3
Caution Touch to access 2nd page.
4
Touch [Date]. 3
Touch on FM or AM repeatedly on the left
• Risk of road accidents! Never watch video or
of the screen to select band:
adjust settings while you drive.
•
1
Press to turn on the unit. •
4
»
The available OSD (On-Screen Display) Briefly touch
languages are displayed. station by step.
•
5
Touch year digit to highlight this digit.
Play disc
6
Touch / to set year.
7
Repeat step 4 and 5 to set month and day. You can play video, audio or images stored on the
following discs:
Set Time • DVD video, DVD-R, DVD-RW
2
Touch a language to select. 1
Touch [Clock Time]. • VCD
»
The OSD language is changed to the 2
Touch hour/minute digit to highlight the digit. • Audio CD, CD-R, CD-RW
selected language immediately. 3
Touch / to set hour/minute.
• To adjust screen brightness, press DIMMER Note
on the remote control, then press or . Set time format
• Ensure that the disc contains playable
1
• To turn off the unit, press and hold for 3 Touch[Time format]repeatedly to toggle
content.
seconds. between [12Hr] and [24Hr] options.
1
Insert the disc into the disc slot with label
Tip
side facing up.
»
Set date and time
• When date/time is set, touch to go back
»
1 to the upper level menu, or touch to go to
Touch to display main menu.
»
the main menu.
Radio D c s i USB S D H C
Sun
Listen to Radio
Sep 27, 2009
1
Touch to display home menu.
Bluetooth AV_IN1 Navigation Settings
2
Touch [Radio].
2
Touch [Settings].
»
Setting menu displays.
a b
4
Radio screen displays. 2
Note Search for other Bluetooth device with
your device.
Depends on where you bought the unit,
•
3
Select "CED1700" in the pairing list.
you can play DVD discs with one of the
4
following region codes:
Enter default password "0000".
»
If pairing succeeds. the dial screen
displays.
Countries where you Supported DVD
bought the unit region code
China
FM band options: FM1, FM2, FM3 Asia Pacific, Taiwan,
Korea
AM band options: AM1, AM2
or to tune to a radio
Latin America
Touch or for over 1 seconds to
Make a call
tune to a radio station automatically.
1
Touch on top of the screen.
Russia, India
»
The dial screen displays.
3
Play USB device 4
Note
• Ensure that the device contains playable 2
Touch number icons directly to input
content.
phone number.
3
After the phone number entered, touch
1
Open the lid of USB socket. .
2 »
Insert the USB to the USB socket. The unit starts dialing.
»
Play starts automatically.
Or you can make call through quick dial:
Front panel closes automatically.
1
Touch [QUICK DIAL] on the dial screen.
Play starts automatically.
»
Play with Bluetooth device The screen prompts to enter quick dial
To remove the disc, press the button.
» When the disc is ejected, the unit number.
switches to the previous source,
if connected. Otherwise, the
Pair the Bluetooth-enabled devices
unit switches to [Radio] mode
automatically. To connect your Bluetooth device to the unit, you
need to pair the device to the unit. Pairing needs
only to be done once.
You can pair up to eight devices.
1
Turn on the Bluetooth function on your
device.
c
2
Touch a preset number on the screen.
»
The unit dials the selected preset phone
number.
Tip
• If no quick number is preset, the screen
prompts [Empty].
Receive call
By default, all incoming calls are received
automatically.
1
If there is incoming call, [Incoming call...]
flashes on the screen. Speak into the
Bluetooth microphone.
2
When conversation ends, tap (red) to
terminate the call.
Tip
• You can select to receive calls manually by
set [Auto answer] to [Off] status.