1. Manuals
  2. Brands
  3. RHINO Manuals
  4. Front End Loaders
  5. 1594
  6. Operator's manual

RHINO 1594 Operator's Manual

Rhino mounts lawn mower user manual
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Published 01/11
This Operator's Manual is an integral part of the safe operation of this machine and must
be maintained with the unit at all times. READ, UNDERSTAND, and FOLLOW the Safety
and Operation Instructions contained in this manual before operating the equipment. C01-
Cover
®
RHINO
1020 S. Sangamon Ave.
Gibson City, IL 60936
800-446-5158
Email: parts@servis-rhino.com
OPERATOR'S MANUAL
© 2011 Alamo Group Inc.
1594
LOADER
F-4282C
Part No.
$0.00

Advertisement

Table of Contents
loading

Related Manuals for RHINO 1594

Summary of Contents for RHINO 1594

  • Page 1 Published 01/11 OPERATOR’S MANUAL This Operator's Manual is an integral part of the safe operation of this machine and must be maintained with the unit at all times. READ, UNDERSTAND, and FOLLOW the Safety and Operation Instructions contained in this manual before operating the equipment. C01- Cover ®...
  • Page 2 To the Owner/Operator/Dealer All implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded operator who recognizes the potential hazards and follows reasonable safety practices. The manufacturer has designed this implement to be used with all its safety equipment properly attached to minimize the chance of accidents.

  • Page 3: Table Of Contents

    TABLE OF CONTENTS SAFETY SECTION ... 1-1 General Safety Instructions and Practices ... 1-2 Operator Safety Instructions and Practices ... 1-4 Equipment Operation Safety Instructions and Practices ... 1-6 Connecting or Disconnecting Implement Safety Instructions and Practices ... 1-12 Transporting Safety Instructions and Practices ... 1-13 Maintenance and Service Safety Instructions and Practices ...
  • Page 4 Operating the Tractor and Loader ... 4-20 Operating the Loader ... 4-25 Operating Bale Spear ... 4-37 Valve Lock ... 4-38 Loader Storage ... 4-39 Transporting the Tractor and Implement ... 4-40 Transporting on Public Roadways ... 4-42 Hauling the Tractor and Implement ... 4-43 Troubleshooting Guide ...

  • Page 5: Safety Section

    SAFETY SECTION Safety Section 1-1...

  • Page 6: General Safety Instructions And Practices

    (ROPS). Always wear seat belts. Serious injury or even death could result from falling off the tractor--particularly during a turnover when the operator could be pinned under the ROPS. 1594 01/11 © 2011 Alamo Group Inc. SAFETY (SG-3)
  • Page 7 Push and pull the control levers in and out several times to remove pressure. Do not work under raised Boom or Bucket unless components are securely blocked up to prevent inadvertent dropping. 1594 01/11 © 2011 Alamo Group Inc. SAFETY...

  • Page 8: Operator Safety Instructions And Practices

    Battery posts, terminals and related accessories contain lead and lead compounds, chemicals known to the state of California to cause cancer, birth defects or other reproductive harm. 1594 01/11 © 2011 Alamo Group Inc. SAFETY Never allow inexperienced or untrained personnel to...
  • Page 9 In those conditions, personal protective equipment including an appropriate respirator must be used. If excessive dust is generated, a dust collection or suppression system should also be used during operation. 1594 01/11 © 2011 Alamo Group Inc. SAFETY (SG-32)

  • Page 10: Equipment Operation Safety Instructions And Practices

    Operate the Tractor and/or Implement controls only while properly seated in the Tractor seat with the seat belt securely fastened around you. Implement may cause serious injury or death. 1594 01/11 © 2011 Alamo Group Inc. SAFETY (S3PT-12)
  • Page 11 Do not raise the loader into an overhead structure or allow a raised attachment to contact overhead structures. Sudden or unexpected contact with an overhead structure could result in serious injury. 1594 01/11 © 2011 Alamo Group Inc. SAFETY (SL-05)
  • Page 12 Do not work from the loader or attachments. Do now allow any riders on the loader, tractor or attachments. Falling off the loader could result in serious injury and/or tractor run over. 1594 01/11 © 2011 Alamo Group Inc. SAFETY...
  • Page 13 Use extreme care when piling material above 6 feet high. Material could shift and fall onto the operator or bystanders. The material could crush or suffocate the operator or bystander resulting in serious injury or death. (SL-17) 1594 01/11 © 2011 Alamo Group Inc. SAFETY (SL-15) (SL-16)
  • Page 14 Turn curves or go up slopes only at low speed and using a gradual turning angle. Go up slopes with the Implement located uphill. Slow down on rough or uneven surfaces. (SPU-2) 1594 01/11 © 2011 Alamo Group Inc. SAFETY...
  • Page 15 Sudden or unexpected movement or dropping of the loader and attachment could result in serious injury. 1594 01/11 © 2011 Alamo Group Inc. SAFETY...

  • Page 16: Connecting Or Disconnecting Implement Safety Instructions And Practices

    For added safety when lifting loads above the height of the operator, install a certified Falling Object Protective Structure. 1594 01/11 © 2011 Alamo Group Inc. SAFETY...

  • Page 17: Transporting Safety Instructions And Practices

    Tractor wheel contact with any wash out, drop off or the ground obstruction with a raised loader could result in the tractor tipping over and causing serious bodily injury. 1594 01/11 © 2011 Alamo Group Inc. SAFETY Determine the maximum...

  • Page 18: Maintenance And Service Safety Instructions And Practices

    When transporting the Equipment use the Tractor flashing warning lights and follow all local traffic regulations. Do not modify or alter this Implement. Implement, any of its components or any Implement function. 1594 01/11 © 2011 Alamo Group Inc. SAFETY (SL-39) (SG-6)
  • Page 19 Be alert to worn component surfaces which have sharp edges. Sharp surfaces can inflict severe laceration injuries if proper hand protection is not worn. (SG-37) 1594 01/11 © 2011 Alamo Group Inc. SAFETY (SG-15) (SG-20)

  • Page 20: Storage And Parking Safety Instructions And Practices

    Safety Messages and operation instruction in each of the appropriate sections of the Tractor and Equipment Manuals. Pay close attention to the Safety Signs affixed to the Tractor and Equipment. 1594 01/11 © 2011 Alamo Group Inc. SAFETY...

  • Page 21: Decal Location

    (Some shipping and handling charges may apply). Contact your Rhino dealer to order replacement decals. 1594 01/11 Safety Section 1-17 © 2011 Alamo Group Inc.
  • Page 22 49696 51448 03200347 00776031 55580 * Provided by Tractor Manufacturer. Replace if missing from Tractor. NOTE: Order D438 Safety Decal Sheet which includes all safety decals. 1594 01/11 © 2011 Alamo Group Inc. SAFETY LEVEL DESCRIPTION WARNING Loader Safety DANGER...

  • Page 23: Decal Description

    -Do not allow riders on tractor or loader. -Do not allow children or untrained persons to operate loader. D469 Crushing Hazard, Electrocution Hazard, Falling Hazard. D468 Crushing Hazard D471 1594 01/11 © 2011 Alamo Group Inc. SAFETY Safety Section 1-19...
  • Page 24 DANGER! - Use ROPS and seatbelt at all times. Add recommended rear ballast. Operate tractor at low speeds. Failure to comply may result in serious injury or death. D470 NAME - 1594 P/N 55630 1594 01/11 © 2011 Alamo Group Inc. SAFETY...
  • Page 25 DO NOT transport or operate without the SMV. P/N 03200347 Read Operator’s Manual! The operator’s manual is located inside this canister. missing order one from your dealer. P/N 00776031 1594 01/11 © 2011 Alamo Group Inc. SAFETY If the manual is Safety Section 1-21...
  • Page 26 Do not use attachment if it disengages. -NEVER walk or work underneath raised loader or attachment (Located on the Quick Attach Device Only) P/N D516 1594 01/11 © 2011 Alamo Group Inc. SAFETY Safety Section 1-22...

  • Page 27: Federal Laws And Regulations

    Some regulations specify that no one under the age of 16 may operate power machinery. It is your responsibility to know what these regulations are in your own area or situation. (Refer to U.S. Dept. of Labor, Employment Standard Administration, Wage & Home Division, Child Labor Bulletin #102.) 1594 01/11 © 2011 Alamo Group Inc. SAFETY...

  • Page 29: Introduction Section

    INTRODUCTION SECTION Introduction Section 2-1...
  • Page 30 The 1594 Loader is designed with care and built with quality materials by skilled workers. Proper assembly, maintenance, and operating practices, as described in this manual, will help the owner/operator get years of satisfactory service from the machine. The purpose of this manual is to familiarize and instruct. The Assembly Section instructs the owner/operator in the correct assembly of the Front End Loader using standard and optional equipment.
  • Page 31 (ROPS). Always wear seat belts. Serious injury or even death could result from falling off the tractor--particularly during a turnover when the operator could be pinned under the ROPS. 1594 01/11 © 2011 Alamo Group Inc. INTRODUCTION (SG-30)
  • Page 32 INTRODUCTION The RHINO 1594 Loader is designed for four-wheel drive tractors. They are intended to lift only loose materials that will fit in the bucket. All cylinders are double-acting. Parking stands support loader so tractor can be “driven in” for quick attaching.
  • Page 33 Alamo Group within thirty days of delivery of the implement. 3. Record the Loader Model and Serial Numbers on the Warranty page. Keep this as part of the permanent maintenance file for the implement 1594 01/11 © 2011 Alamo Group Inc. INTRODUCTION...

  • Page 35: Assembly Section

    ASSEMBLY SECTION Assembly Section 3-1...

  • Page 36: General Information

    Refer to tractor operator’s manual for steering stop adjustment. NOTE: Reference to left and right used in these instructions refer to position when seated in the operating position on tractor. 1594 01/11 © 2011 Alamo Group Inc. ASSEMBLY (SG-14)

  • Page 37: Preparing Tractor

    (Do not lift tires off the ground!) Make sure the mounting pins can be rotated easily. 1594 01/11 © 2011 Alamo Group Inc.

  • Page 38: Installing Left And Right Midmounting Brackets

    2. Secure with Hex bolts M14 X 25 MM (5) and M14 Lockwashers (6). 3. Torque bolts after all have been installed using General Torque Specifications (See Torque for Fasteners in Maintenance Section). 1594 01/11 © 2011 Alamo Group Inc. ASSEMBLY...

  • Page 39: Plumbing Loader

    Port #1 - Red, Tilt Cylinder Rod End Port #2 - Blue, Tilt Cylinder Base End Port #3 - Black, Lift Cylinder Rod End Port #4 - Yellow, Lift Cylinder Base End 1594 01/11 © 2011 Alamo Group Inc. ASSEMBLY Assembly Section 3-5...

  • Page 40: Attaching Bucket To Loader

    NOTE: Do not lift the tractor tires off the ground. While pressure is applied, make sure the loader mounting pins can be rotated easily. 6. Tighten all remaining hardware to the torque level shown in the General Torque Specification Chart at the end of this document. 1594 01/11 © 2011 Alamo Group Inc. ASSEMBLY Assembly Section 3-6...

  • Page 41: Connecting Quick Attach Device (Optional)

    By standing at the side of the loader, inspect the connection between the quick hitch and attachment. Never walk or work under or allow any person to be underneath a raised loader or attachment. 1594 01/11 © 2011 Alamo Group Inc. ASSEMBLY Assembly Section 3-7...

  • Page 42: Pre-Operation Check

    Be sure lift cylinders are fully retracted. 2. Lubricate all grease fittings with SAE multi-purpose grease. 3. Check hydraulic fluid level in tractor. Fill to recommend level, using oil specified in tractor operator’s manual. 1594 01/11 © 2011 Alamo Group Inc. ASSEMBLY disconnect.

  • Page 43: Dismounting The Loader

    Relax lift cylinders and bucket cylinders by moving each control lever in both directions. Disconnect hydraulic hoses from tractor. 11. Start tractor engine and release brakes. Slowly back tractor out of loader. 1594 01/11 © 2011 Alamo Group Inc. ASSEMBLY Assembly Section 3-9...

  • Page 44: Mounting Loader

    A steel hammer or drift could generate flying metal fragments and result in injury. Always wear safety glasses when using a hammer to remove or install pins. 1594 01/11 © 2011 Alamo Group Inc. ASSEMBLY...

  • Page 45: Operation Section

    OPERATION SECTION Operation Section 4-1...
  • Page 46 Pictures contained in this section are intended to be used as a visual aid to assist in explaining the operation of 1594 loader and are not necessarily of 1594 loader or exact tractor. Some pictures may show shields removed for purposes of clarity. NEVER OPERATE this implement without all shields in place and in good operational condition.

  • Page 47: Standard Equipment And Specifications

    Standard Equipment and Specifications • Model 1594 Loaders are compatible with Kubota L3940 Tractors. • Each loader package includes the basic loader, mounting brackets, hydraulic plumbing, grill guard, quick attach device and bucket. Tractor * Maximum Lift Height at Pivot Pin...

  • Page 48: Operator Requirements

    NOTE: Hearing loss from loud noise [from tractors, chain saws, radios, and other such sources close to the ear] is cumulative over a lifetime without hope of natural recovery. 1594 01/11 © 2011 Alamo Group Inc. OPERATION...
  • Page 49 If you are using a tractor equipped with a cab, make sure the cab is rated for appropriate environmental exposure. Be safe and always wear proper protection. Short or long term exposure to certain chemicals and materials can result in serious injury or death. 1594 01/11 © 2011 Alamo Group Inc. OPERATION (SG-22)
  • Page 50 Protective Eye Glasses, Goggles, or Face Shield • Hard Hat • Steel Toe Safety Footwear • Gloves • Hearing Protection • Close Fitting Clothing • Respirator Filter Mask operating conditions) OPS-L- 0021 1594 01/11 © 2011 Alamo Group Inc. OPERATION (SG-41) (depends Operation Section 4-6...

  • Page 51: Tractor Requirements

    Only operate the tractor with the ROPS in the raised position and seat belt fastened. Tractor models not equipped with a ROPS and seat belt should have these life saving features installed by an authorized dealer. OPS-U- 0003 1594 01/11 © 2011 Alamo Group Inc. OPERATION...

  • Page 52: Tractor Lighting And Smv Emblem

    (See Standard Equipment and Specifications). When determining required counterweight bucket should be at maximum forward position (bucket pivot point at the same height as boom pivot point on mast). 1594 01/11 © 2011 Alamo Group Inc. OPERATION...

  • Page 53: Getting On And Off The Tractor

    Before getting onto the tractor, the operator must read and completely understand the implement and tractor operator manuals. If any part of either manual is not completely understood, consult an authorized dealer for a complete explanation. OPS-L- 0022 4.1 Boarding the Tractor 1594 01/11 © 2011 Alamo Group Inc. OPERATION determined...

  • Page 54: Dismounting The Tractor

    Use hand rails and steps when exiting the tractor. Be careful of your step and use extra caution when mud, ice, snow or other matter has accumulated on the steps or hand rails. Use all handrails and steps for support and never rush or jump off the tractor. OPS-L- 0024 1594 01/11 © 2011 Alamo Group Inc. OPERATION...

  • Page 55: Starting The Tractor

    Never bypass the ignition switch by short circuiting the starter solenoid. After the tractor engine is running, avoid accidental contact with the tractor transmission to prevent sudden and unexpected tractor movement. OPS-L-0025 1594 01/11 © 2011 Alamo Group Inc. OPERATION (SG-23)

  • Page 56: Pre-Operation Inspection And Service

    Power brake fluid level • Power steering fluid level • Fuel condition and level • Sufficient lubrication at all lube points • Air filter condition OPS-U-0030 1594 01/11 © 2011 Alamo Group Inc. OPERATION (SG-21) The following Operation Section 4-12...

  • Page 57: Loader Pre-Operation Inspection And Service

    Before operation, a complete inspection and service is required to ensure the loader is in a good and safe working condition. Damaged and/or broken parts should be repaired and/or replaced immediately. To ensure the loader is ready for operation, conduct the following. OPS-L-0027 1594 01/11 © 2011 Alamo Group Inc. OPERATION...
  • Page 58 • Ensure each hydraulic cylinder is installed and retained correctly. Ensure the proper size pins are used to retain the cylinders in place and are secured properly. OPS-L-0005 1594 01/11 © 2011 Alamo Group Inc. OPERATION installed Mount Frame Assembly...
  • Page 59 • Inspect the condition of the bucket lug weldments. • Inspect condition of bushings. OPS-L-0007 1594 01/11 © 2011 Alamo Group Inc. OPERATION along hoses, Hydraulic Hoses Operation Section 4-15...
  • Page 60 The engine coolant fluid level is full The radiator is free of debris The air filter is in good condition Operator’s Signature: DO NOT OPERATE an UNSAFE TRACTOR or FRONT END LOADER 1594 01/11 © 2011 Alamo Group Inc. OPERATION Condition at Start of Shift...
  • Page 61 The Control Valve Lock functions correctly The Pivot Pins are properly lubricated The Loader Storage Stands are in good condition Operator’s Signature: DO NOT OPERATE an UNSAFE TRACTOR or FRONT END LOADER 1594 01/11 © 2011 Alamo Group Inc. OPERATION Condition at Start of Shift...

  • Page 62: Driving The Tractor And Loader

    Failure to maintain adequate vision of the public roadway and traffic can result in serious injury or even death. (STI-10) 1594 01/11 © 2011 Alamo Group Inc. OPERATION (S3PT-12)

  • Page 63: Starting The Tractor

    When engaged the differential lock will prevent or limit the tractor from turning. During normal working conditions, locking the differential provides no benefit and should not be used. OPS- L- 0015_A 1594 01/11 © 2011 Alamo Group Inc. OPERATION Operation Section 4-19...

  • Page 64: Driving The Tractor And Loader

    Always wear your seatbelt when operating the loader to reduce the possibility of serious injury from a tractor tip over or roll over. 1594 01/11 © 2011 Alamo Group Inc. OPERATION...
  • Page 65 Stepping off the tractor can permit electrical current to pass through the body resulting in electrocution. 1594 01/11 © 2011 Alamo Group Inc. OPERATION...
  • Page 66 Do not operate the loader from the ground. Operate the tractor and loader only while seated in the tractor seat with the seatbelt fastened. The loader could fall crushing a person resulting in serious injury or death. 1594 01/11 © 2011 Alamo Group Inc. OPERATION...
  • Page 67 8 inches and most noticeable when the tractor is stationary. Sudden or unexpected movement of the loader and attachment could result in serious injury to the operator or bystanders. (SL-33) 1594 01/11 © 2011 Alamo Group Inc. OPERATION (SL-16)
  • Page 68 Tractor wheel contact with any wash out, drop off or the ground obstruction with a raised loader could result in the tractor tipping over and causing serious bodily injury. 1594 01/11 © 2011 Alamo Group Inc. OPERATION (SL-35)

  • Page 69: Operating The Loader

    OPS-L-0033 7.5 Operating the Loader The following text and illustrations offer suggested loader and tractor operating techniques. FILLING THE BUCKET Approach and enter the pile with a level bucket. 1594 01/11 © 2011 Alamo Group Inc. OPERATION Operation Section 4-25...
  • Page 70 Time is lost if two or more attempts are made to fill the bucket on each pass. 1594 01/11 Operation Section 4-26 © 2011 Alamo Group Inc.
  • Page 71 Attachment can be adjusted by using bucket cylinders. CARRYING THE LOAD Position bucket below tractor hood for maximum stability and visibility, whether bucket is loaded or empty. 1594 01/11 Operation Section 4-27 © 2011 Alamo Group Inc.
  • Page 72 DUMPING THE BUCKET Lift bucket high enough to clear side of vehicle. Move tractor in as close as possible to side of vehicle, then dump bucket. 1594 01/11 Operation Section 4-28 © 2011 Alamo Group Inc.
  • Page 73 Float will also prevent mixing of surface material with stockpile material. Float position will reduce the chance of surface gouging when removing snow or other material. 1594 01/11 Operation Section 4-29 © 2011 Alamo Group Inc.
  • Page 74 If the pile sides are too high and liable to cause cave-in, use loader to break down the sides until a slot can be cut over the top. 1594 01/11 Operation Section 4-30 © 2011 Alamo Group Inc.
  • Page 75 Another method for large dirt piles is to build a ramp approach to the pile. It is important to keep the bucket level when approaching a bank or pile. This will help prevent gouging the work area. 1594 01/11 Operation Section 4-31 © 2011 Alamo Group Inc.
  • Page 76 Make additional passes until desired depth is reached. During each pass, use only bucket control while working depth. This will allow you to concentrate on controlling bucket angle to maintain a precise cut. 1594 01/11 Operation Section 4-32 © 2011 Alamo Group Inc.
  • Page 77 Back grade occasionally with loaded bucket to eliminate ruts and holes. Use the heel of the bucket by holding down pressure of the lift cylinder. Approach pile with a level bucket. 1594 01/11 Operation Section 4-33 © 2011 Alamo Group Inc.
  • Page 78 Do not use bucket in dumped position for bulldozing. This method, shown above, will impose severe shock loadings on dump linkage, bucket cylinder and tractor. 1594 01/11 Operation Section 4-34 © 2011 Alamo Group Inc.
  • Page 79 OPERATION Leave dirt in bucket. Dumping on each pass wastes time. Operate tractor at right angles to ditch. Take as big a bite as tractor can handle without lugging down. 1594 01/11 Operation Section 4-35 © 2011 Alamo Group Inc.
  • Page 80 Never lifting large objects with equipment that does not have an anti-rollback device. • Moving slowly and carefully, avoiding rough terrain. • Tilt bucket forward while lifting to maintain bucket angle. 1594 01/11 © 2011 Alamo Group Inc. OPERATION Operation Section 4-36...

  • Page 81: Operating Bale Spear

    Load bale spear by approaching from round end to prevent cutting strings or puncturing plastic or net wrap.Tilt bale spear upward to prevent bale from falling off of spear, 1594 01/11 © 2011 Alamo Group Inc. OPERATION Operation Section 4-37...

  • Page 82: Valve Lock

    Always have a heavy attachment, such as a bucket mounted on loader when it is removed from tractor. It is important not to put excessive weight on parking stands with lift cylinder retraction. Damage may result. 1594 01/11 © 2011 Alamo Group Inc. OPERATION Operation Section 4-38...

  • Page 83: Loader Storage

    Store the loader in a clean, dry place resting securely on parking stands at ground level. • Use spray touch-up enamel where necessary to prevent rust and maintain the appearance of the loader. OPS-L-0010_B 1594 01/11 © 2011 Alamo Group Inc. OPERATION Perform Parking Stand Operation Section 4-39...

  • Page 84: Transporting The Tractor And Implement

    Serious injury could result. (SL-04) 1594 01/11 © 2011 Alamo Group Inc. OPERATION (SG-10) Determine the maximum...
  • Page 85 Use extreme caution and avoid hard applications of the tractor brakes when towing heavy loads at road speeds. Never tow the implement at speeds greater than 20 MPH (32 kph). OPS-U- 0018 1594 01/11 © 2011 Alamo Group Inc. OPERATION Locking the wheels...

  • Page 86: Transporting On Public Roadways

    Do not exceed the legal speed limit set in your country for agricultural tractors. Always stay alert when transporting the tractor and implement on public roads. Use caution and reduce speed if other vehicles or pedestrians are in the area. OPS-L- 0020 1594 01/11 © 2011 Alamo Group Inc. OPERATION...

  • Page 87: Hauling The Tractor And Implement

    OPS-U- 0025 1594 01/11 © 2011 Alamo Group Inc. OPERATION Operation Section 4-43...

  • Page 88: Troubleshooting Guide

    Loader chatters or vibrates when raising or lowering External leakage Pump noisy Excessive wear on bucket cutting edge 1594 01/11 © 2011 Alamo Group Inc. OPERATION POSSIBLE CAUSE Hydraulic oil too heavy. Oil filter plugged. Hydraulic pump worn. Oil line restricted or leaking.

  • Page 89: Maintenance Section

    MAINTENANCE SECTION Maintenance Section 5-1...
  • Page 90 If oil does penetrate the skin, have the injury treated immediately by a physician knowledgeable and skilled in this procedure. Never attempt to lubricate, adjust, or remove material from the Implement while it is in motion or while tractor engine is running. 1594 01/11 © 2011 Alamo Group Inc. MAINTENANCE (SG-6)
  • Page 91 These parts are made and tested to Rhino specifications. Non-genuine "will fit" parts do not consistently meet these specifications. The use of “will fit” parts may reduce equipment performance, void warranties, and present a safety hazard. Use genuine Rhino parts for economy and safety. 1594 01/11 © 2011 Alamo Group Inc. MAINTENANCE...

  • Page 92: Lubrication Schedule

    Lubricate all grease fittings: one at each end of lift boom arms and one at rod and base ends of each lift and bucket cylinders. NOTE: Fully retract bucket to a comfortable height to grease bucket/loader boom joint. Do not reach or stand under a raised loader or attachment without proper support. 1594 01/11 Maintenance Section 5-4 © 2011 Alamo Group Inc.

  • Page 93: Daily Maintenance

    • Tighten all connections before starting engine or pressurizing lines. NOTE: If any fluid is injected into skin, obtain medical attention immediately or gangrene may result. 1594 01/11 © 2011 Alamo Group Inc. MAINTENANCE Maintenance Section 5-5...

  • Page 94: Storage

    Failure to do so will result in tractor hydraulic pump damage. 1. Store loader with attachment attached. 2. Place dust caps on hydraulic quick couplers. 1594 01/11 © 2011 Alamo Group Inc. MAINTENANCE (SL-26) (SL-27) securely Maintenance Section 5-6 (SL-13)
  • Page 95 MAINTENANCE 3. Do not remove attachment from stored loader. 4. Do not allow children to play on or around loader. 1594 01/11 Maintenance Section 5-7 © 2011 Alamo Group Inc.

  • Page 96: Proper Torque For Fasteners

    NOTE: These values apply to fasteners as received from supplier, dry or when lubricated with normal engine oil. They do not apply if special graphited or molydisulphide greases or other extreme pressure lubricants are used. This applies to both UNF fine and UNC coarse threads. 1594 01/11 Maintenance Section 5-8 © 2011 Alamo Group Inc.
  • Page 97 MAINTENANCE 1594 01/11 Maintenance Section 5-9 © 2011 Alamo Group Inc.
  • Page 98 MAINTENANCE 1594 01/11 Maintenance Section 5-10 © 2011 Alamo Group Inc.

  • Page 100: Limited Warranty

    LIMITED WARRANTIES 1.01. Rhino warrants for one year from the purchase date to the original non-commercial, governmental, or municipal purchaser (“Purchaser”) and warrants for six months to the original commercial or industrial purchaser (“Purchaser”) that the goods purchased are free from defects in material or workmanship. 1.02.
  • Page 101 To keep your implement running efficiently and safely, read your manual thoroughly and follow these directions and the Safety Messages in this Manual. The Table of Contents clearly identifies each section where you can easily find the information you need. The OCCUPATIONAL SAFETY AND HEALTH ACT (1928.51 Subpart C) makes these minimum safety require- ments of tractor operators: REQUIRED OF THE OWNER:...
  • Page 102 1594 LOADER 1594 -SOM-01/11 P/N F-4282C Printed U.S.A...

Table of Contents