Download Print this page
Shuttle DH110 Series Quick Manual

Shuttle DH110 Series Quick Manual

Advertisement

Quick Links

DH110 Series Quick Guide【English】
__p
Front Panel
F1. MIC-in
F2. Headphone
F3. Power LED
F5
F6
F7
F8
F4. HDD LED
F5. Power Button
F6. SD Card Reader
F7. USB 3.0 Port
F8. USB 2.0 Port
F1 F2 F3
F4
Back Panel
B1. COM1 Port
(RS232/RS422/RS485)
B2. COM2 Port (RS232 only)
B1
B2
B3. Power Jack (DC IN)
B4. HDMI Port
B5. DisplayPort
B6. eSATA+USB 2.0 Combo
B7. LAN Port
B8. USB 3.0 Port
B3
B4
B5
B6
B7
B8
B9
B10
B9. PS/2 Port
B10. Clear CMOS & Power Button
Left / Right Panel
®
Kensington
Lock Port
Kensington
Motherboard Illustration
Power Button-SW2
SD Card Reader Slot
USB 3.0 (x2) Port
USB 2.0 (x2) Port
AC Back Auto
Power ON-JP2
J1
Fan Connector
J2
-CPU_FAN1
LGA1151 Package
CPU Socket
Intel H110 Chipset
USB Connector
J3
-CN12
DC IN
HDMI Port
DisplayPort
eSATA+USB 2.0
Combo
Jumper Settings
AC Back Auto Power ON (JP2)
J1
Default:Short 1-2 =>Function Disable
1=AMP(+)
2=GND
Fan Connector (CPU_FAN1)
J2
1=GND
2=+12V
3=SPEED_SENSE
4 3 2 1
4=PWM_CTRL
USB Connector (CN12)
J3
1=GND
4 3 2 1
2=DATA+
3=DATA-
4=+5V
Audio Connector (AUDIO1)
J4
1=10K to AGND
8=JACK_DET
2=LINE-R
9=20K to AGND
3=NA
10=FRONT-R
4=LINE-L
11=AUDIO1-JD
5=5.1K to AGND
12=MIC-R
6=FRONT-L
13=AGND
7=NULL
14=MIC-L
COM1 & COM2 Power Switch (JP1)
J5
COM PORT Pin 9 "Ring Indicator" (RI) configuration:
Configure COM 1 with the first jumper:
- Short Pin 1-2: Pin 9 = RI (default)
- Short Pin 5-7: Pin 9 = +5V
- Short Pin 7-9: Pin 9 = +12V
®
Lock Port
Configure COM 2 with the second jumper:
- Short Pin 3-4: Pin 9 = RI (default)
- Short Pin 6-8: Pin 9 = +5V
- Short Pin 8-10: Pin 9 = +12V
1=-XRI1
6=+5V
2=COM_-XRI1
7=COM1_PWR
3=-XRI2
8=COM2_PWR
4=COM_-XRI2
9=+12V
5=+5V
10=+12V
HDD LED
Power LED
COM Port (COM1,COM2)
Headphone
J6
MIC-in
Audio Connector
J4
1=DCD
6=DSR
-AUDIO1
2=RX
7=RTS
3=TX
8=CTS
SATA Cable Connector
-SATA1
4=DTR
9=RI
5=GND
10=NULL
DDR3L SO-DIMM Slot
Debug Connector (DBG1)
J7
1=LCLK_24M
6=+3.3V
COM1 & COM2 Power
J5
Switch-JP1
2=LAD1
7=LAD3
3=LRESET-
8=GND
COM PORT-COM1,COM2
J6
4=LAD0
9=LAD2
5=LFRAME-
10=NULL
Debug Connector-DBG1
J7
VGA Connector-CN6
J8
M.2 2230 A,E Key slot
Safety Information
M.2 2242/2260 M Key slot
Battery Connector
Read the following precautions before setting up a Shuttle XPC.
J9
-CN1
Clear CMOS & Power
CAUTION
J10
Button-SW1
Incorrectly replacing the battery may damage this computer.
PS/2 Port
Replace only with the same or equivalent as recommended by Shuttle.
USB 3.0 (x2) Port
Dispose of used batteries according to the manufacturer's instructions.
LAN Port-LAN1,LAN2
62R-DH1100-5201
DH110
English.Spanish.Korean.
Traditional Chinese.Japanese.
French. German Quick Guide
VGA Connector (CN6)
J8
1=GND
11=HSYNC
2=GND
12=GND
3=DDC_CLK
13=GND
1
4=GND
14=GND
5=DDC_SDA
15=BLUE
2
6=GND
16=+5V
7=GND
17=GREEN
8=GND
18=+5V
9=VSYNC
19=RED
10=GND
20=+5V
A. Begin Installation
For safety reasons, please ensure that the power cord is
disconnected before opening the case.
1. Unscrew the two screws of the chassis cover.
13
14
12
11
2. Slide the cover backwards and upwards.
10
9
8
7
6
5
2
4
3
2
1
1
3. Unfasten the rack mount screw and remove the rack.
B. CPU and ICE Module Installation
2
4
6
8 10
1. Unfasten the four ICE module attachment screws and unplug the fan
connector.
1
3
5
7
9
2. Remove the ICE module from the chassis and put it aside.
2
4
6
8 10
Please note the pins of the LGA 1151 socket bend easily.
Always apply extreme care and little force when installing a CPU
and limit the number of times you remove or exchange it. Before
installation, make sure to turn off the computer and unplug the
1
3
5
7
9
power cord from the mains to avoid damage.
 Follow the steps below to correctly install the CPU into the
motherboard CPU socket.
3. First unlock and raise the socket lever.
2
4
6
8 10
1
3
5
7
9
4. Tear off the protective membrane from the metal load plate. Lift the
metal load plate from the CPU socket.
The product's colour and specifications may vary from the actually shipping product.
L
Battery Connector (CN1)
J9
1=BATPWR(+3V)
2
20
2=GND
1
19
Clear CMOS & Power Button (SW1)
J10
1=RTCRST-
2=+5V
3=GND
4=PWRSW-
DO NOT touch socket contacts. To protect the CPU socket, always
replace the protective socket cover when the CPU is not installed.
5. Please orientate the CPU correctly and align the CPU notches with the
socket alignment keys. Make sure the CPU sits perfectly horizontal,
then push it gently into the socket.
Triangle Pin1
Marking on the CPU
Socket
1151
CPU
Notch on the CPU/
Alignment Key of the
CPU Socket
Please be aware of the CPU orientation, DO NOT force the CPU into
the socket to avoid bending of pins and damage of the CPU!
6. Close the metal load plate, lower the CPU socket lever and lock in place.
7. Spread thermal paste evenly on the CPU surface.
Metal load plate
Thermal Paste
application area
Load lever
Retention tab
Please do not apply excess amount of thermal paste.
HDD Rack
C. Memory Module Installation
This mainboard does only support 1.35V DDR3L SO-DIMM
memory modules.
1. Locate the SO-DIMM slot on the mainboard.
2. Align the notch of the memory module with the one of the memory slot.
SO-DIMM slot
notch
Fan connector
3. Gently insert the module into the slot in a 45-degree angle.
4. Carefully push down the memory module until it snaps into the
locking mechanism.
1
2
45-degree
angle
3
Tear off the protective
membrane.
Metal load plate
Latch
Latch
5. Repeat the above steps to install additional memory modules, if required.
1
2
4
1
3
D. Component Installation
1. As shown, unfasten the screw first.
M.2 2242/2260 M
Key slot
M.2 2230 A,E
Key slot
2. Install the M.2 device into the M.2 slot and secure with the screw.
3. Screw the ICE module to the mainboard. Note to press down on the
opposite diagonal corner while tightening each screw.
4. Connect the fan connector.
3
1
2
4
Fan connector
5. Place a HDD or SSD in the rack and secure with the four screws from
the side.
6. Connect the Serial ATA to the HDD or SSD.
Slide the rack into the chassis and refasten the screws.
Serial ATA Cable
E. Complete
1. Replace the cover and refasten the screws.
2 . Complete.
Please press the "Del" key while booting to enter BIOS. Here,
please load the default BIOS settings.
53R-DH1103-H001

Advertisement

loading
Need help?

Need help?

Do you have a question about the DH110 Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel