Advertisement
Controls & Operation
E
H
B
J
A
K
I
Note: This Operator's Manual covers several
models. Rider features may vary by model. Not all
features in this manual are applicable to all rider
models and the rider depicted may differ from
yours.
Note: References to LEFT, RIGHT, FRONT, and REAR
indicate that position on the rider when facing
forward while seated in the operator's seat.
Vehicle Control Module (VCM) (A)
WARNING
Never leave a running machine unattended. Always
disengage PTO, set parking brake, stop rider and remove
power key to prevent unintended starting.
The vehicle control
module (VCM) is
located on the
left fender of the
rider seated in the
operator's position
The VCM is the
PTO
location of several
F
control buttons for
1
sec.
your rider. The VCM
inludes the START/
STOP button, PTO
(blades ON/OFF)
button , Reverse Caution Mode (RCM) button,
Headlight button, Cruise Control button, LCD
Screen and the Battery Level Indicator.
CAUTION
Prior to operating the rider, refer to both Safety Interlock
Switches and Starting The Rider in the Operation section
of this manual for detailed instructions regarding the VCM
and operating the rider in REVERSE CAUTION MODE.
10
F
D
G
Figure 3-1
Start/Stop Button
The start/stop button is used to start and
stop the rider when the key switch is in the
ON position. To start the rider, press the
start/stop button for two seconds (two beeps). To
stop the rider, press the start/stop button for one
second (one beep).
PTO (Blades ON/OFF) Button
The PTO button is used to engage the blades.
To operate, press the PTO button for one
second. The green indicator light below the
PTO button is illuminated when there is power to the
cutting deck and the LCD Screen displays "CUT DECK
ON." Pressing the PTO button again will disengage
power to the cutting deck. The green indicator light is
not illuminated when there is no power to the cutting
deck.
Reverse Caution Mode (RCM) Button
Prior to operating the rider, refer to the Operation section
RCM
of this manual for detailed instructions regarding operating
F
R
the rider in REVERSE CAUTION MODE.
3
sec.
Located on the VCM, the RCM button allows
the rider to be operated in reverse with the
blade(s) engaged. To activate the RCM, press
the RCM button down for three seconds. When
activated, the red indicator light is illuminated. To
de-activate the RCM, press the RCM button again.
When the RCM is not activated, the red indicator light
is not illuminated. Refer to the Operation section of
this manual for more information on operating the
rider in the reverse caution mode.
Note: Mowing in reverse is not recommended.
Use extreme caution while operating the rider in the
REVERSE CAUTION MODE. Always look down and behind
before and while backing. Do not operate the rider when
children or others are around. Stop the rider immediately if
someone enters the area.
C
CAUTION
WARNING
Headlight Button
The headlight button is used to turn
the headlights on or off.
Cruise Control Button
Pressing the cruise control button
while the rider is in motion allows the
rider to remain at a constant ground
speed without applying pressure to
the forward drive pedal, the LCD Screen
displays "CRUISE ON" when the cruise control is
activated. The cruise control can be disengaged by
pressing either the cruise control button, the brake
pedal or the forward drive pedal. Refer to the
Operation section of this manual for detailed
instructions regarding the cruise control feature.
Note: Cruise control will not engage at the rider's
fastest ground speed. If the operator should
attempt to do so, the rider will automatically
decelerate to the fastest optimal mowing ground
speed.
Note: Cruise control will not engage in reverse.
LCD Screen & Battery Level Indicator
The LCD display & battery level indicator are used
to provide instructions, warnings and information
about your rider systems and the battery level of
your rider.
Key Switch (B)
The key switch is located on the left fender and
sends power to the VCM when the switch is in the
ON (I) position. The rider cannot be started unless
the key switch is in the ON (I) position. Turning the
switch to the OFF (O) position turns the rider off
and stops the flow of power to the VCM.
Note: Before your rider can be
Do Not
started, the safety label covering the
Remove Label
While On Display
key switch must be removed. This
Ne pas
Supprimer l'étiquette
label is in place to prevent
Pendant l'affichage
I25799
unintended starting when the rider is
on display. Peel off the label to access
the key switch.
Forward Drive Pedal (C)
The forward drive pedal is located on the right
side of the steering column, along the running
board. Press the forward drive pedal forward to
cause the rider to travel forward. Ground speed is
also controlled with the forward drive pedal. The
further forward the pedal is pressed, the faster the
rider will travel. The pedal will return to its original/
neutral position when it is released.
3
Advertisement
