3u 16-bay ip-san storage with reinforced reliability (122 pages)
Summary of Contents for Advantech SQF-MSDS1-2G-85E
Page 1
SQFlash Industrial Class 10 Micro SD Card SQFlash Micro SD Card Technical Manual Class 10 (SQF-MSDx1-xM/G-21x) Specifications subject to change without notice, contact your sales representatives for the most update information. REV 0.3 Page 1 of 22 May 4, 2016...
SQFlash Industrial Class 10 Micro SD Card CONTENTS Overview .................... 4 Standard Features ................5 Additional Features ................6 Pin Assignment and Block Diagram ..........8 Power Consumption ............... 11 DC Characters ................. 11 AC Characters ................. 14 Dimensions ..................19 Appendix: Part Number Table ............
Add SLC Advantech reserves the right to make changes without further notice to any products or data herein to improve reliability, function, or design. Information furnished by Advantech is believed to be accurate and reliable. However, Advantech does not assure any liability arising out of the application or use of this information, nor the application or use of any product or circuit described herein, neither does it convey any license under its patent rights nor the rights of others.
SQFlash Industrial Class 10 Micro SD Card Overview The SQFlash Micro Secure Digital card (SQF-MSD) is fully compliant to the specification released by SD Card Association. The Command List supports [Part 1 Physical Layer Specification Ver3.01 Final] definitions. Card Capacity of Non-secure Area, Secure Area Supports [Part 3 Security Specification Ver3.00 Final] specifications. The microSD 3.0 card comes with 8-pin interface, designed to operate at a maximum operating frequency of 50MHz or 100MHz.
SQFlash Industrial Class 10 Micro SD Card Standard Features Support SD system specification version 3.0 Card capacity of non-secure area and secure area support [Part 3 Security Specification Ver3.0 Final] Specifications Support SD SPI mode Designed for read-only and read/write cards ...
Page 7
SQFlash Industrial Class 10 Micro SD Card NAND flash Data Retention – 10 years Specifications subject to change without notice, contact your sales representatives for the most update information. REV 0.3 Page 7 of 22 May. 4, 2016...
SQFlash Industrial Class 10 Micro SD Card Flash Management Error Correction Code (ECC) Flash memory cells will deteriorate with use, which might generate random bit errors in the stored data. Thus, SQF-MSD applies the BCH ECC algorithm, which can detect and correct errors occur during read process, ensure data been read correctly, as well as protect data from corruption.
Page 9
SQFlash Industrial Class 10 Micro SD Card Endurance JEDEC defined an endurance rating TBW (TeraByte Written), following by the equation below, for indicating the number of terabytes a flash drive can be written which is a measurement of flash drive’s expected lifespan, represents the amount of data written to the device.
SQFlash Industrial Class 10 Micro SD Card Pin Assignment and Block Diagram SD Mode SPI Mode Name Type Description Name Type Description DAT2 I/O/PP Data Line[bit2] Card Detect/ Chip Select (neg CD/DAT3 I/O/PP Data Line[bit3] true) Command/Response Data In Supply voltage Supply voltage Clock SCLK...
SQFlash Industrial Class 10 Micro SD Card Power Consumption Table list as below is the power consumption of SQF-MSD card with different type of flash memory. Capacity Flash Structure Read Write Idle 4GB x 1 8GB x 1 16GB 8GB x 2 32GB 8GB x 4 64GB...
Page 12
SQFlash Industrial Class 10 Micro SD Card Peak Voltage and Leakage Current Parameter Symbol Unit Remarks Peak voltage on all lines -0.3 +0.3 All Inputs Input Leakage Current All Outputs Output Leakage Current Bus Signal Line Levels Parameter symbol Unit Remark...
Page 13
SQFlash Industrial Class 10 Micro SD Card Power Down and Power Cycle (1) When the host shuts down the power, the card VDD shall be lowered to less than 0.5Volt for a minimum period of 1ms. During power down, DAT, CMD, and CLK should be disconnected or driven to logical 0 by the host to avoid a situation that the operating current is drawn through the signal lines.
SQFlash Industrial Class 10 Micro SD Card AC Characters microSD Interface timing (Default) Parameter Symbol Unit Remark Clock CLK (All values are referred to min(V ) and max(V ≤ 10 pF card Clock frequency Data Transfer Mode (1 card) ≤...
Page 15
SQFlash Industrial Class 10 Micro SD Card microSD Interface Timing (High-Speed Mode) Card Input Timing (High Speed Card) Card Output Timing (High Speed Mode) Parameter Symbol Unit Remark Clock CLK (All values are referred to min(V ) and max(V Clock frequency Data Transfer ≤...
Page 16
SQFlash Industrial Class 10 Micro SD Card microSD Interface timing (SDR12, SDR25, SDR50 and SDR104 Modes) Input Symbol Unit Remark tCLK 4.80 208MHz (Max.), Between rising edge, VCT= 0.975V tCR, tCF 0.2 * tCLK tCR, tCF < 2.00ns (max.) at 100MHz, CCARD=10pF Clock Duty Clock Signal Timing ...
Page 17
SQFlash Industrial Class 10 Micro SD Card Output Timing of Variable Window (SDR104) Symbol Unit Remark Card Output Phase -350 +1550 Delay variable due to temperature change after tuning tODW 0.60 tODW=2.88ns at 208MHz Output Timing of Fixed Data Window ...
Page 18
SQFlash Industrial Class 10 Micro SD Card Parameter Symbol Unit Remark Input CMD (referenced to CLK rising edge) ≤ 10 pF card Input set-up time (1 card) ≤ 10 pF card Input hold time (1 card) Output CMD (referenced to CLK rising edge) Output Delay time during Data ≤...
SQFlash Industrial Class 10 Micro SD Card 10. Dimensions Specifications subject to change without notice, contact your sales representatives for the most update information. REV 0.3 Page 19 of 22 May. 4, 2016...
Page 20
SQFlash Industrial Class 10 Micro SD Card Specifications subject to change without notice, contact your sales representatives for the most update information. REV 0.3 Page 20 of 22 May. 4, 2016...