Really Good Stuff STORE MORE BINDER NOOK Instructions

STORE MORE BINDER NOOK ™ INSTRUCTIONS - 2, 4 and 6-Shelf Units
6-SHELF ASSEMBLY INSTRUCTIONS
Your 6-Shelf Unit is made up of a Store More Binder Nook ™
2-Shelf Base Unit and two 2-Shelf Add-On Units.
STEP THIRTEEN:
Assemble the 4-Shelf Unit following the previous directions
on pages 2-3 from Step 1 through Step 11, substituting Item
#8A for #8 in Step 11. Set aside #8, and complete Step 12.
STEP FOURTEEN:
Install the remaining item #13 studs (included in the
hardware package for the 2-Shelf Add-On Unit into the four
holes marked "Y" located at the top of your 4-Shelf Binder
Nook—refer to diagram.)
STEP FIFTEEN:
Place the 2-Shelf Add-On Unit on the top of the 4-Shelf Unit
and tighten the four locking cams. The locking cams must be
locked into position by turning them a full 180 degrees with
the assembly tool.
Completed
6-Shelf Unit
Your Store More Binder Nook
attached to a wall. This step is very important as your Binder Nook
could be pulled over, causing bodily injury to a child or adult.
Before you start: Position your assembled Binder Nook in the corner
of the room you have selected.
Using an electric drill, drill directly through the mounting holes of the
Binder Nook into the wall. The diameter of the hole should be 1/4".
Drill deep enough to accommodate the length of the wall anchor
(1-1/2"). Remove the Binder Nook. Install an anchor into each mounting
hole. Place the Binder Nook back into position, and insert a screw.
Note: If floor trim prevents the unit from mounting flush to the wall,
we suggest the placement of a shim between the wall and the Binder
Nook Unit.
4 Helping Teachers Make A Difference © 2007 Really Good Stuff
®
Item 8
Item 9
Item 10
Item 6
X
X X X
Completed Item 8A
4-Shelf Unit
~ IMPORTANT NOTICE ~
™ is now assembled and must be
® 1-800-366-1920 www.reallygoodstuff.com Made in Guangzhou, China -0410
STORE MORE BINDER NOOK ™ INSTRUCTIONS - 2, 4 and 6-Shelf Units
Thank you for purchasing our exclusive Store More Binder Nook
Before you begin, please refer to the Parts List to ensure that all materials
needed for assembly have been received. Please also read the Helpful Hints to
ensure assembly goes smoothly.
HELPFUL HINTS:
• Check the direction of the arrows on each locking cam during assembly.
All arrows must point toward the small holes located on the outer edge of
the panels. (See diagram, right)
• All studs must be screwed in approximately 1/2" until the shoulder meets
the surface. To screw in studs use the assembly tool supplied or a straight
or Philips screwdriver.
PARTS LIST:
4-SHELF
2-SHELF ADD-ON
Item# Description Qty
Item# Description
2-Shelf Base Unit 1
6 Shelf
2-Shelf Add-On Unit 1
8A Shelf
9 Left Side Panel
10 Right Side Panel
6-SHELF
Bag of Hardware:
Locking Cams
Item# Description Qty
Studs
2-Shelf Base Unit 1
Assembly Tool
2-Shelf Add-On Unit 2
Bag of Wall Mounting Hardware:
Screws
Decorative Plugs
Wall Anchors
Shelf Illustrations show markings
from both sides of shelves:
Locking Cam
Stud
Assembly Tool
Rev. 4/10
Helping Teachers Make A Difference © 2007 Really Good Stuff
®
™ .
Pointed end of cross-slot
must be positioned
as shown
2-SHELF BASE
Qty Item# Description Qty
3 Base Support 1
1
1 4 Shelf 1
5 Left Side Lower Panel 1
1
1 6 Shelf 1
7 Right Side Lower Panel 1
1
14 8 Shelf 1
Bag of Hardware: 1
14
1 Locking Cams 16
Studs 16
1
2 Assembly Tool 1
Bag of Wall Mounting Hardware: 1
2
2 Screws 2
Decorative Plugs 2
Wall Anchors 2
® 1-800-366-1920 www.reallygoodstuff.com Made in Guangzhou, China 1