Advertisement
HI-09UCS / HI-09FCS TECHNICAL BOOKLET
THICKNESS ADJUSTMENT
If you need to adjust the thickness of coins to be accepted,
just use a small slotted screwdriver, plug into the slot and
rotate to fit the thickness you want.
RECORD MODE
If you want to enter the record mode, set DIP4, DIP5 of the DIP
SWITCH to "ON" positions. Then turn on the power.
SELECT OUTPUT PULSE WIDTH
If you want to appoint the pulse width (50ms or 100ms, default setting is 100ms),
you must enter the "RECORD MODE" first. Then set DIP4 to the following position.
1.50ms: DIP4 to "OFF"
2.100ms DIP4 to "ON"
After appointing the pulse width. Enter the "MEMORIZE COINS" item to begin
memorizing the coins.
CLEAR RECORD FOR SINGLE CHANNEL
The multi coin selector has 8 channels to record. Its 8 channels represent it can
record 8 kinds of coins separately. If you want to clear a channel, please proceed
as follows:
Channel 1
Channel 2
Channel 3
Channel 4
Steps
(Coin 1)
(Coin 2)
(Coin 3)
A
00011
10011
01011
B
Switch on
Switch on
Switch on
Switch on
C
00010
10010
01010
D
00011
10011
01011
OK
OK
OK
Turn off the power for the next operation as soon as steps A,B,C,D is complete.
1
(ON)
(OFF)
0
MEMORIZE COINS
1.You must enter the "RECORD MODE" first. Then make sure which channel you
want to save by setting DIP1, DIP2, DIP3 to the appropriate positions. Then insert
10 coins of the same currency and makings. The coin selector magnet will operate
three times to indicate a correct operation. Then be sure to turn the power off for
the next operation.
2.If another different coins is necessary to memorize, please repeat the operation
above- mentioned again.
3.If some channels of the set were memorized some time ago, please clear the records
for all channels first.
2.6
3
2.2
1.8
Channel 5
Channel 6
Channel 7
Channel 8
(Coin 4)
(Coin 5)
(Coin 6)
(Coin 7)
(Coin 8)
11011
00111
10111
01111
11111
Switch on
Switch on
Switch on
Switch on
11010
00110
10110
01110
11110
11011
00111
10111
01111
11111
OK
OK
OK
OK
OK
Steps
Channel 1
Channel 2
Channel 3
A
00011
10011
01011
Coin 1
Coin 2
Coin 3
B
Insert 10 coins
Insert 10 coins
Insert 10 coins
C
3 clicks
3 clicks
3 clicks
D
Switch off
Switch off
Switch off
RATIO LIST CHOICES
1.Under "OPERATION MODE", the switch DIP3, DIP2, DIP1 positions are assigned to 8 ratio lists.
2.Under "RECORD MODE", the switch DIP3, DIP2, DIP1 positions are assigned to 8 coin channels
List 1
List 2
List 3
00000
10000
01000
Operation
Mode
Pulse
Pulse
Pulse
Output
Output
Output
Count
Count
Count
Coin 1
1/2
1/4
1
Coin 2
1
1/2
1
Coin 3
1
1/2
2
Coin 4
2
1
4
Coin 5
4
2
8
Coin 6
5
2
8
Coin 7
8
4
10
Coin 8
10
5
10
3.Insert one coin of the first kind, the value "1/2" will be memorized in the set. Then insert one
coin of the first kind again, the new value "1/2" will be added to the previous "1/2", hence the
set outputs "1" pulse. To this analogizes. Insert one coin of the 8th kind, the set outputs "10" pulses.
4.The pulses generated above-mentioned output via "IMPULSE" from the control board(pcb-09-2).
Besides, one coin being inserted will outputs "one" pulse via "output ch" corresponded
to its coin channel(see Impulse and channel ratio table). For example: Under "channel 5" with
"ratio list 3". Insert one coin will result in outputting 8 pulses via "IMPULSE" from the control
board, and outputting 1 pulse via "output ch5" simultaneously.
If the ratio table can't meet customer requirements, please contact the original factory.
OPERATION MODE
1.Set DIP4, DIP5 to the "OFF" position when the power is off.
2.Turn on the power, and set the DIP3, DIP2, DIP1 positions to
correspond the ratio list you need.
3.Now you can start using the multi coin selector.
THREE OUTPUT INTERFACE
(1) 10p signal cable + control board for HI-09FCS/HI-09UCS
(2) 5p signal wire use for HI-09FCS connecting to game board and meter.
(3) 6p signal wire use for HI-09UCS connecting to game board and meter.
HUAI I ELECTRONICS CO.,LTD
Channel 4
Channel 5
Channel 6
Channel 7
11011
00111
10111
01111
Coin 4
Coin 5
Coin 6
Coin 7
Insert 10 coins
Insert 10 coins
Insert 10 coins
Insert 10 coins
3 clicks
3 clicks
3 clicks
3 clicks
Switch off
Switch off
Switch off
Switch off
List 4
List 5
List 6
List 7
List 8
11000
00100
10100
01100
11100
Pulse
Pulse
Pulse
Pulse
Pulse
Output
Output
Output
Output
Output
Count
Count
Count
Count
Count
1
1/2
1/2
1/2
1/4
1
1
1
1
1/2
2
1
3
2
2/3
2
2
6
5
4
5
12
6
4
NA
NA
10
10
NA
NA
12
NA
10
NA
NA
NA
NA
(1)
(2)
1. +12V
2. Counter (Meter)
3. GND
4. Impulse (Credit)
5. Inhibit (Enable)
(3)
1. GND
2. +12V
3. +12V
4. Counter (Meter)
5. Impulse (Credit)
6. Inhibit (Enable)
Channel 8
11111
Coin 8
Insert 10 coins
3 clicks
Switch off
.
Other
Output
Terminal
1 Pulse
Output
Output ch1
Output ch2
Output ch3
3
Output ch4
6
Output ch5
7
Output ch6
Output ch6
Output ch6
+12V
GND
Impulse
Inhibit
1
2
3
4
5
1
2
3
4
5
6
Advertisement
