WEI-YA HI-09UCS User Manual

MULTI-COIN SELECTOR
HI-09UCS / HI-09FCS
(Drop inserting type)
Feature
*Support 8 channels (coins) self-programming without PC.
*With an inhibit wire for game board.
*With 6 ch. Parallel output for each channel (coin) control.
*Support one coin then multi pulse output (impulse out ratio).
*With narrow or wide impulse width select (100ms and 50ms).
*Adjustable 4 kinds of coin thickness.
Specifications:
Parameter
Power Input
Consumption
Impulse Output
Signals
Inhibit Input
Out1~6 Output
Connector Con2 Input/output
Con3 Input/output
Con5 Input/output
User con trols 5-ch Sw1, sw2, sw3 for channel or impulse ratio select.
dip-switch Sw4, sw5 for mode and other function select.
Overall Dimension HI-09UCS: 102x99x55 mm
(HXWXD) HI-09FCS: 124.5x120.5x64.5 mm
Speed of acceptable Max. 3 coins/second.
Coin size Diameter 18mm~30mm
(mm)
Thickness Position
Adjust
Thickness Range 1.2~2.0
Working temperature 5° ~50°
Weight HI-09UCS: 240g
HI-09FCS: 300g
Specifications
DC 10~15V, 300mA max standby 50mA.
5.0 Watts max standby 0.6 watts.
Multi pulse (normal "High" level)
High enable( +3v~+15v)
1 pulse/coin
4 pin male Extend connect port
09FCS 5 pin male General I/O port
09UCS 6 pin male General I/O port
1.8 2.2 2.6 3
1.2~2.4 1.2~2.8 1.2~3.0
(Front inserting type)
Operation mode: Before switching on the dc power,
Set DIP 4,DIP 5 to the "OFF" position.
Impulse and channel ratio table (500)
Multi coin mode
DIP3, DIP2, DIP1 XXX XXO XOX XOO OXX
Ratio Impulse out Ratio Impulse out Ratio (bonus)
Channel 1 2 3 4 5
(Coin)
1 XXX 1/2 1/4 1 1 1/2
2 XXO 1 1/2 1 1 1
3 XOX 50C 1 1/2 2 2 1
4 XOO 1$ 2 1 4 2 2
5 OXX 2$ 4 2 8 4 4+1
6 OXO 5 2 8 4 NA
7 OOX 8 4 10 10 NA
8 OOO 10 5 10 10 NA
DIP SW "X" means off , "O" means on
Accessory
HI-09UCS or HI-09FCS X1
Control board (pcb-09-2) X1
10p Signal cable X1
User manual X1
Screw bag (HI-09FCS only) X1
5P (09F) or 6P (09U) Signal wire X 1
Installation
Case 1:
Using 10p signal cable connect HI-09UCS/HI-09FCS
to control board (pcb-09-2). And need 4 wires connect
control board (pcb-09-2) to game board.
The 4 wires define as below:
1. +12V: for dc power (12 volt).
2. GND: for dc power (ground).
3. IMPULSE: for credit signal (output signal).
4. INHIBIT: control by game board for enable
or disable coin selector (input).
Case 2:
Using 5P or 6P signal wire connect to HI-09UCS/HI-09FCS
another end connect to game board and meter.
The 5P wire define as below (HI-09FCS only)
1. +12V
2. Counter (Meter)
1
2
3. GND
3
4. Impulse (Credit)
4
5
5. Inhibit
HUAI I ELECTRONICS CO.,LTD
FOR EURO COIN
V2.9
Record mode: Before switching on the dc
power, set DIP 4, DIP 5 to the "ON"
position.
Out DIP SW Function Select
OXO OOX OOO
Coin signal
DIP Sw4 width
6 7 8
(impulse)
1/2 1/2 1/4 1
1 1 1/2 2
DIP Sw5 Blank
3 2 1+1/2 3
O->X->O Makes channel data Blank
5+1 4+1 2+1 4
10+2 5+1 4+2 5
NA 8+2 5+2 6
1. GND
NA 10+2 NA 6
NA NA NA 6
2. +12V
3. Output ch5
4. Output ch6
5. Impulse output
6. Inhibit control
7. Output ch1
8. Output ch2
9. Output ch3
10. Output ch4
The 6P wire define as below (HI-09UCS only)
1. GND
2. +12V
1
2
3. +12V
3
4. Counter (Meter) 4
5
5. Impulse (Credit)
6
6. Inhibit
(500)
Action
X Record 50ms impulse
O Record 100ms impulse
O Normal
1 2
3 4
5 6
7 8
9 10
Please make sure direction
+12V
GND
Impulse
Inhibit