Panasonic WV-SPN311 Installation Manual

Installation Guide
Included Installation Instructions
Network Camera
WV-SPN311/WV-SPN310
Model No.
* This illustration represents WV-SPN311
(Please purchase the recommended lens separately.)
● This manual describes the installation procedures, cable connections, and the angle of view
adjustment of this product.
● Before reading this manual, be sure to read the Important Information.
● This manual describes how to install the network camera using model WV-SPN311 as an example.
For U.S. and Canada: For Europe and other countries:
Panasonic System Communications Panasonic Corporation
Company of North America,
http://panasonic.net
Unit of Panasonic Corporation
of North America
www.panasonic.com/business/ Panasonic System Networks Co., Ltd.
Fukuoka, Japan
For customer support, call 1.800.528.6747
Two Riverfront Plaza, Newark, NJ 07102-5490
Authorised Representative in EU:
Panasonic Canada Inc.
Panasonic Testing Centre
5770 Ambler Drive, Mississauga,
Panasonic Marketing Europe GmbH
Ontario, L4W 2T3 Canada
Winsbergring 15, 22525 Hamburg, Germany
(905)624-5010
www.panasonic.ca
Panasonic System Networks Co., Ltd. 2014
PGQX1622ZA sL0914-0 Printed in China
Major operating controls
The component names of the camera are as follows. Refer to the illustration when installing or
adjusting the camera.
ACT indicator
● When data is being sent via the network camera Blinks green (accessing)
LINK indicator
● When the camera is able to communicate with Lights orange
the connected device
*1 12 V DC power supply terminal
*1 Network connector RJ45
*1 Microphone/line input connector *1 EXT I/O terminals
SPN311
MONITOR OUT terminal
*1 Audio output connector
(factory shipment: NTSC monitor)
SPN311
*1 The detailed specifications on the right describe terminals with markings.
*2 SDXC/SDHC/SD memory card is described as SD memory card.
Standard accessories
Important Information ............................... 1 pc. CD-ROM* ................................................ 1 pc.
1
Installation Guide (this document) ............ 1 set Code label* 2 .............................................. 1 pc.
Warranty card ........................................... 1 set
*1 The CD-ROM contains the operating instructions and different kinds of tool software programs.
*2 This label may be required for network management. The network administrator shall retain the code label.
The following parts are used during installation procedures.
A Tripod mount base ............................... 1 pc. F Washer ................................................. 1 pc.
B Power cord plug ................................... 1 pc. G Spring washer ...................................... 1 pc.
C Safety wire lug ...................................... 1 pc.
B
D Wire lug fixing screws
(M2.5 x 8 mm {5/16 inches}) ............. 2 pcs.
(of them, 1 for spare)
E Safety wire ........................................... 1 pc.
About notations
The following notations are used when describing the functions limited for specified models.
The functions without the notations are supported by all models.
The functions with this notation are available when using the model WV-SPN311.
SPN311
The functions with this notation are available when using the model WV-SPN310.
SPN310
*1 Depending on the scanning application
used, the Data Matrix may not be able to
be read correctly. In this case, access the
site by directly entering the following URL.
http://security.panasonic.com/pss/security/
support/qr_sp_select.html
MIC Data Matrix: To our website* 1
SPN310
SD ON/OFF button
Auto back focus button (ABF)
SPN311
Slide cover
SD slot (SD) Focus assist (F.A.)
Clamp for SD
Lens (recommended)
ALC lens connector
memory card
SD MOUNT indicator
*2
● When an SD memory card is inserted and could Lights off → Blinks green →
be recognized Lights off
● When data can be saved after the SD memory card is Lights off → Lights green
inserted and the SD ON/OFF button is pressed
● When data can be saved to the SD memory card Lights green
● When the SD memory card is removed after holding down Lights green → Blinks green → Lights off
the SD ON/OFF button for about 2 seconds
● When data cannot be saved to the SD memory card because Lights off
an abnormality was detected or the SD memory card is
configured not to be used
INITIAL SET button
● How to initialize the camera
Follow the steps below to initialize the network camera.
T urn off the power of the camera. When using a PoE hub, disconnect the LAN cable from
q
the camera. When using an external power supply, disconnect the power cable plug from
the 12 V DC power supply terminal.
T urn on the power of the camera while holding down the INITIAL SET button, and then
w
keep holding down the button for 5 seconds or more. About 2 minutes later, the camera will
start up and the settings including the network settings will be initialized.
IMPORTANT:
● When the camera is initialized, the settings including the network settings will be initial-
ized. Note that the CRT key (SSL encryption key) used for the HTTPS protocol will not
be initialized.
● Before initializing the settings, it is recommended to write down the settings in advance.
● Do not turn off the power of the camera during the process of initialization. Otherwise, it
may fail to initialize and may cause malfunction.
NTSC/PAL switch
● The MONITOR OUT terminal output can be switched for the NTSC monitor/PAL monitor.
IMPORTANT:
● This is valid if the [Monitor out] is set to [Switch priority] ([Switch priority] is selected by
default).For details, refer to the Operating Instructions (included in the CD-ROM).
SD ERROR/ABF indicator SD ERROR/F.A. indicator
SPN311 SPN310
● When ABF (Auto Back Focus) operation is being Blinks red (Interval of 1 time/ second)
executed
SPN311
● When the focus assist function is activated Blinks red (1 time)
SPN310
● When the focus ring is positioned near the best Blinks red (1 time)
focus position
SPN310
● When the set is being started Lights red
● When an SD memory card is recognized normally Lights red → Lights off
● When the SD card slot is not used or an abnormality is Lights red
detected in SD card after the camera has started
Making connections
Turn off each system's power supply before making a connection. Before making connections,
prepare the required peripheral devices and cables.
Example of audio cable connector Example of LAN cable connector
Connect a LAN cable (category 5 or better, straight)
Connect a LAN cable (category 5 or better, straight) to the network connector.
IMPORTANT:
● Use all 4 pairs (8 pins) of the LAN cable.
● The maximum cable length is 100 m {328 feet}.
● Make sure that the PoE device in use is compliant with IEEE802.3af standard.
● When connecting both the 12 V DC power supply and the PoE device for power
supply, 12 V DC will be used for power supply.*
* If a 12 V DC power supply and a PoE hub or router are used at the same time,
network connections may not be possible. In this case, disable the PoE settings.
Refer to the operating instructions of the PoE hub or router in use.
* Depending on the PoE device used, if you disconnect 12 V DC while 12 V DC
power supply and a PoE hub or router are used at the same time, the power supply
may stop, causing the camera to restart.
● When the LAN cable is disconnected once, reconnect the cable after around
2 seconds. When the cable is quickly reconnected, the power may not be supplied
from the PoE device.
SPN310
Connect an external amplifier-embedded speaker to the audio output cable
Connect a stereo mini plug (ø3.5 mm) (Audio output is monaural.). Use an external powered speaker.
● Output impedance : Approx. 600 Ω (unbalanced)
● Recommended cable length : Less than 10 m {32.8 feet}
● Output level : –20 dBV
IMPORTANT:
● Connect/disconnect the audio cables and turn on the power of the camera after turning
off the power of the audio output devices. Otherwise, loud noise may be heard from
the speaker.
● Make sure that the stereo mini plug is connected to this cable. When a monaural mini
plug is connected, audio may not be heard.
When connecting a monaural speaker with amplifier, use a locally procured conversion
cable (mono-stereo).
Microphone/line input cable
SPN311
Connect a monaural mini plug (ø3.5 mm).
● Input impedance: Approx. 2 kΩ (unbalanced)
● Recommended cable length: Less than 1 m {3.28 feet} (for microphone input)
Less than 10 m {32.8 feet} (for line input)
● Recommended microphone: Plug-in power type (option)
● Input level for the line input: Approx. –10 dBV
● Recommended sensitivity of microphone: –48 dB ±3 dB (0 dB=1 V/Pa,1 kHz)
When connecting to a network using a PoE hub
Before starting the installation, check the entire system configuration. The following illustration
gives a wiring example of how to connect the camera to the network via a PoE device (hub).
Powered speaker Adjustment monitor PoE device (hub)
SPN311
Microphone
LAN cable (category 5
SPN311
or better, straight)
Powered speaker
LAN cable
(category 5 or better, straight)
SPN311
Adjustment monitor
Microphone
SPN311 Recommended total extended
cable length*
1
*1 Recommended cable length from the speaker : less than 10 m {32.8 feet}
Recommended cable length from the microphone : less than 1 m {3.28 feet}
Connect the power cable
Caution:
● A READILY ACCESSIBLE DISCONNECT DEVICE SHALL BE INCORPORATED
TO THE EQUIPMENT POWERED BY 12 V DC POWER SUPPLY.
● ONLY CONNECT 12 V DC CLASS 2 POWER SUPPLY (UL 1310/CSA 223) or
9 mm
LIMITED POWER SOURCE (IEC/EN/UL/CSA 60950-1).
{11/32 inches}
Connect the output cable of the DC power supply to the power cable plug (accessory).
L oosen the screw of the power cable plug (accessory), strip 3 mm to 7 mm {1/8 inches to
q
9/32 inches} from the end of the wire, twist the stripped part of the wire sufficiently to avoid
short circuit, and then connect the output cable to the power cable plug (accessory).
Tighten the screw of the power cable plug. (Recommended tightening torque: 0.34 N·m
w
{0.25 lbf·ft})
Note:
● Check whether the stripped part of the wire is not exposed and is securely con-
nected.
● When connecting an external power supply to the camera, use the AWG 16 to
AWG 24 single-wired or stranded wired cables.
IMPORTANT:
● The 12 V DC power supply shall be insulated from the commercial AC power.
● Be sure to use the power cable plug provided with this product.
● Be sure to fully insert the power cable plug into the 12 V DC power supply terminal.
Otherwise, it may damage the camera or cause malfunction.
● When installing the camera, make sure that excessive force is not applied to the
power cable.
● Be sure to use an AC adaptor compliant with the Specifications (written in the indi-
cation label on the bottom side of this unit) regarding power source and power con-
sumption.
Connect the alarm input/output cable
Connect the cables of external devices to the EXT I/O terminal plug.
When connecting an external device, remove 8 mm - 9 mm of the outer jacket of the cable
q
and twist the cable core to prevent the short circuit first.
Specification of cable (wire): AWG 20 - AWG 26, Single core, twisted
Push down the button of the desired terminal on the external I/O terminal plug with a ball-
w
point pen, and release the button when the cable of the external device is fully inserted
into the terminal hole.
Note:
● Check whether the stripped part of the wire is not exposed and is securely connected.
<Ratings>
● ALARM IN1(DAY/NIGHT IN
SPN311
● ALARM IN1
SPN310
Input specification : No-voltage make contact input (4 V - 5 V DC, internally pulled up)
OFF : Open or 4 V - 5 V DC
SPN311
ON : Make contact with GND (required drive current: 1 mA or more)
● ALARM OUT, AUX OUT
Output specification : Open collector output (maximum applied voltage: 20 V DC)
ON : 4 V - 5 V DC by internal pull-up
OFF : Output voltage 1 V DC or less (maximum drive current: 50 mA)
* The default of EXT I/O terminals is "Off".
button
1 2 3 4
External I/O terminal plug
IMPORTANT:
● Do not connect 2 wires or more directly to a terminal. When it is necessary to con-
●Supply voltage: 2.5 V ±0.5 V
nect 2 or more wires, use a splitter.
● Off, input, and output of the external I/O terminal 2 and 3 can be switched by con-
figuring the setting. Refer to the Operating Instructions on the provided CD-ROM
for further information about the EXT I/O terminal 2 and 3 (ALARM IN2, 3) settings
("Off", "Alarm input", "Alarm output" or "AUX output").
● Install external devices so that they do not exceed the rating of the network camera.
● When using the EXT I/O terminals as the output terminals, ensure they do not
cause signal collision with external signals.
LAN cable <Required cable>
(category 5 or better, straight)
LAN cable (category 5 or better, straight)
Use a LAN cable (category 5 or better, cross) when directly connecting the camera to a PC.
PC
IMPORTANT:
● The adjustment monitor is used for checking the adjustment of the angular field of
view when installing the camera or when servicing. It is not provided for recording/
monitoring use.
● Depending on the monitor, some characters (camera title, preset ID, etc.) may not
be displayed on the screen.
● Use a switching hub or a router which is compliant with 10BASE-T/100BASE-TX.
● If a PoE hub is not used, each network camera must be connected to a 12 V DC
power supply.
● When using 12 V DC, power supply from a PoE hub or router is not required.
), ALARM IN2, ALARM IN3
ALARM IN1, DAY/NIGHT IN
(Alarm input terminal 1, DAY/NIGHT input terminal )
SPN311
ALARM IN2, ALARM OUT
(Alarm input terminal 2, Alarm output terminal)
ALARM IN3, AUX OUT
(Alarm input terminal 3, AUX output terminal)
GND