Honeywell H3D2S2 Quick Installation Manual

®
equIP Series HD Indoor
IP Minidome Camera
H3D2S2 H3D2SR2
H3D3S2 H3D3SR2
H3D5S2 H3D5SR2
Quick Installation Guide
Document 800-15464V4 – Rev A – 07/2014
Introduction
®
Thank you for purchasing a Honeywell equIP Series indoor minidome camera. Follow the
instructions in this guide to install and log in to your camera. For instructions on configuring the
®
camera, refer to the equIP Series IP Cameras Configuration Guide
documentation CD that came with your camera. If you require additional assistance, please call the
number shown on the back cover of this guide.

Cautions and Warnings

RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
WARNING
To ensure compliance with electrical safety standards,
CSA Certified/UL Listed Class 2 power adapters are required. Power over
Ethernet (PoE) shall be provided by listed Information Technology
Equipment meeting the IEEE 802.3af PoE standard. The PoE is not intended
to be connected to exposed (outside plant) networks.
WARNING
Risk of explosion if battery is replaced by an incorrect
type. Dispose of used batteries in accordance with local laws.
CAUTION
Invisible LED radiation (850 nm). Avoid exposure to
beam.

Important Safeguards

• Read and keep these instructions
• Please ensure that your installation area can safely support the weight of the camera.
• Do not aim the camera toward an extreme light source to prevent damage to the CCD.
• This camera is rated for indoor operation. Do not expose this camera to rain or moisture.
• Do not touch the camera lens.
• Do not drop the camera or subject it to physical shock.
• Do not use a strong or abrasive detergent when cleaning the camera.
• Avoid operating or storing the unit in extremely humid, dusty, hot/cold environments (where the
operating temperature is outside the recommended range of 14°F to 122°F [–10°C to 50°C]).
Document 800-15464V4 – Rev A – 07/2014
1 Installing the Camera
Before You Begin
Before you begin, check that you have received all of the parts listed below. If any parts are missing
H3D2S2X H3D2SR2X
or damaged, contact your dealer immediately.
H3D3S2X H3D3SR2X
• Camera
H3D5S2X H3D5SR2X • Software and documentation CD
• Power terminal block
• Quick install guide
To install the camera you will also need drilling tools and a Phillips screwdriver (not supplied).
CAUTION
qualified and experienced technicians to conform to all local codes
and to maintain your warranty.
Preparing the Camera
on the software and
1. Loosen the two captive security screws on the dome cover using the supplied Torx key and
remove the dome cover from the camera base.
2. Remove the inner cover from the camera assembly. Press both sides of the inner cover to
release it from the camera assembly.
3. Remove the screw securing the camera assembly to the camera base using a Phillips
screwdriver (not supplied).
4. Remove the camera assembly from the camera base by pressing the tabs on the sides of the
THIS SYMBOL INDICATES
camera assembly. Store the camera assembly in the product box while you install the camera
THAT DANGEROUS VOLTAGE
CONSTITUTING A RISK OF base.
ELECTRIC SHOCK IS PRESENT
WITHIN THE UNIT.
Preparing the Mounting Surface
THIS SYMBOL INDICATES THAT
IMPORTANT OPERATING AND
1. Hold the camera base against the mounting surface and mark the positions of the screw
MAINTENANCE INSTRUCTIONS
ACCOMPANY THIS UNIT.
holes. (Mark and drill a hole for the camera wiring if necessary.)
2. At the marked locations, drill each hole slightly smaller than the supplied screw anchors.
3. Insert the supplied screw anchors into the drilled screw holes.
Mounting the Camera
1. Route the camera wiring through the access hole on the camera base.
2. Install the supplied rubber washers on the four supplied self-tapping screws.
3. Attach the camera base to the mounting surface using the four supplied self-tapping screws.
2

Connecting the Wiring

Power, network, video, audio, and alarm connections are located on the camera's control board.
1
• Security Torx key
• Self-tapping screws (×4)
• Plastic screw anchors (×4)
• Rubber washers (×6)
Installation and servicing should be performed only by
2 3 4 5 6
®
equIP Series Indoor Minidome IP Camera Quick Install Guide
No. Name Description
1 Reset button Restores factory default settings
2 BNC Analog video output
3 Alarm I/O Alarm connection
4 Audio I/O Two-way audio connection
5 Power 12 V DC / 24 V AC power input
6 RJ45 10/100 Mbps Ethernet/PoE input
Connecting to a Power Source
To power the camera, either Power over Ethernet (PoE) or a 12 V DC or a 24 V AC power connection
can be used.
If you are using PoE to power your camera, connect an Ethernet cable to the camera's RJ45 Ethernet
port and plug the other end of the cable into an IEEE 802.3af PoE switch.
WARNING
This product is intended to be powered by a Listed power adapter
with rated output 24 V AC / 700 mA or 12 V DC / 800 mA minimum, marked LPS or
Class 2, or by a Listed ITE with Power over Ethernet rated 48 V DC / 300 mA.
If you are using a 12 V DC or 24 V AC connection to power your camera, insert the wiring into the
supplied power terminal block and plug the terminal block into the power connector on the camera
control board. Refer to the following pin definitions when connecting the wiring:
12 V DC 24 V AC
Pin 1 Power Pin 1 Power 1
Pin 2 Reserved Pin 2 Earth GND
Pin 3 GND Pin 3 Power 2
Connecting to a Network
If you have not already done so, connect a Cat5 or higher Ethernet cable to the RJ45 connector on
the camera control board. For best transmission quality, the Ethernet cable should not be longer
than 328 ft (100 m). After you have connected the Ethernet cable, check the status of the LED
indicators on the RJ45 connector.
• A flashing green LED indicates that the camera is connected to a network.
• A flashing orange LED indicates network activity.
If the LEDs are not lit, re-check the Ethernet cable connection.
Connecting Analog Video
Connect a coaxial cable to the BNC connector on the camera control board and connect the other
end of the cable to a portable service monitor.
Connecting Alarm and Audio Inputs/Outputs
The camera supports one alarm input and one relay output, as well as two-way audio transmissions.
Refer to the following pin definitions when connecting alarm and audio devices:
Alarm Audio
Pin 1 GND (Input–) Pin 1 Output (L)
Pin 2 Input+ Pin 2 Output (R)
Pin 3 Output– Pin 3 GND
Pin 4 Output+ Pin 4 Input
1 2 3
1 2 3 4 1 2 3 4