Fortinet FortiGate Voice-80C Quick Start Manual

LED State
Green
Power
Off
Flashing Green
Status
Green
Green
LINK/
ACT
Flashing
Ports 1 to 8
Amber
10/100
Off
HA Green
Red
Alarm Amber
Off
Green
LINK/
ACT
Flashing
WAN1, WAN2 Green
10/100/
Amber
1000
Off
Green
FXO1 to
FXO4
Off
Visit these links for more information and documentation for your Fortinet product:
Technical Documentation - http://docs.fortinet.com
Fortinet Technical Support - http://support.fortinet.com
Training Services - http://campus.training.fortinet.com
Fortinet Knowledge Center - http://kb.fortnet.com
Package Contents
Interface Type Speed
Ports 1 to 8 RJ-45 10/100 Base-T
WAN1 and WAN2 RJ-45 10/100/1000 Base-T
Console RJ-45 9600 Bps 8/N/1
USB USB
FXO1 to FXO4 RJ-11
FortiGate Voice-80C POWER STATUS
Power
LED
Status
LED
DC+12V
CONSOLE
Console
USB
Ground
Power connection
connection
Connecting
Ensure the FortiGate unit is placed on a stable surface. Connect the following to the FortiGate unit:
• Insert a network cable to WAN1. Insert the other end to the router connected to the Internet, or to the modem.
• Connect a network cable to an Internal port (ports 1 to 8). Insert the other end to a computer or switch.
• Connect the AC Power Cable to the Power Supply.
• Connect the Power Cord to a surge protected power bar or power supply.
Caution: Power supply voltage is 90-240 VAC.
• Optionally, connect an RJ-45 serial cable into the Console port and insert the other end into the management computer.
• Optionally, connect an RJ-11 telephone cable to a phone port (FXO1 to FXO4) and insert the other end into the public switched telephone network (PSTN).
CAUTION: To reduce the risk of fire, use only No. 26 AWG or larger telecommunication line cord.
Configuration Tools
Web Config
The FortiGate Web Config is an easy to use management tool. Use it to configure the administrator
password, the interface and default gateway addresses, and the DNS server addresses.
Requirements:
• An Ethernet connection between the FortiGate unit and management computer.
• A web browser such as FireFox or Internet Explorer on the management computer.
Description
The unit is on.
The unit is off.
The unit is starting up.
The unit is running normally.
Port is online (link).
Port is receiving or sending data (activity).
Connected at 100 Mbps.
Connected at 10 Mbps.
The unit being used in an HA cluster.
A critical error has occurred.
A minor error has occurred.
No errors detected.
Port is online (link).
Port is receiving or sending data (activity).
Connected at 1000Mbps.
Connected at 100 Mbps.
Connected at 10 Mbps.
Administrative status is up.
Administrative status is down.
Protocol Description
Ethernet An eight-port switch connection for the internal network.
Ethernet Redundant connections to the Internet.
RS-232 Optional connection to the management computer. Provides access to the command line interface (CLI).
USB Two optional connections for the USB key, modem, or backup operation.
Four phone ports.
FRONT
HA ALARM
FX01 FX02 FX03 FX04
10/100/1000
HA
LED
interfaces
Alarm
Phone ports
LED
7 5 3 1
USB 8 6 4
2
INTERNAL
Internal interface/switch
connectors 1 to 8
BACK
Power cable connects to
power supply
DC+12V CONSOLE
USB
Straight-through
Optional RJ-45 serial cable
Ethernet cables
connects to serial port on
connect to computers
management computer
on internal network
QuickStart Guide
FortiGate Voice-80C
© Copyright 2009 Fortinet Incorporated. All rights reserved.
Products mentioned in this document are trademarks or registered trademarks
of their respective holders.
Regulatory Compliance
FCC Class B Part 15 CSA/CUS
25 September 2009
WAN1 WAN2 INTERNAL
LINK/ACT LINK/ACT
10/100
1 2 3 4 5 6 7 8
WAN
Internal
interface
WAN1
FX01 FX02 FX03 FX04
WAN2
WAN1/WAN2 Phone ports 1 to 4
Optional RJ-11 telephone
cable connects to phone
port
WAN1
7 5 3 1
8 6 4 2
WAN2
INTERNAL
Straight-through
Ethernet cables
connect to Internet
Command Line Interface (CLI)
The CLI is a full-featured management tool. Use it to configure the administrator password, the interface
addresses, the default gateway address, and the DNS server addresses. To configure advanced settings,
see the Tools and Documentation CD included with the
FortiGate unit.
Requirements:
• The RJ-45 to DB9 serial connection between the FortiGate unit and management computer.
• A terminal emulation application (HyperTerminal for Windows) on the management computer.
POWER STATUS HA ALARM
FX01 FX02 FX03 FX04
10/100/1000
QuickStart Guide
FortiGate Voice-80C POWER STATUS
Tools and Documenation
Copyright 2009 Fortinet Incorporated. All rights reserved.
Trademarks
Straight-through
Ethernet cable DB-9 Serial Cable
AC Power Cable
FX01 FX02 FX03 FX04
FortiGate Voice-80C
WAN1 WAN2 INTERNAL
LINK/ACT LINK/ACT
10/100
1 2 3 4 5 6 7 8
01-40000-111139-20090925
FortiGate-30B
WAN1 WAN2 INTERNAL
LINK/ACT LINK/ACT
HA ALARM FX01 FX02 FX03 FX04
10/100/1000 10/100
1 2 3 4 5 6 7 8
REGISTER
4 Rubber feet
RJ-45 to
Power Supply