Brother MFC-T910DW Quick Setup Manual

MFC-T910DW
Quick Setup Guide
Read the Product Safety Guide first, then read this Quick Setup Guide
for the correct installation procedure.
Unpack the machine and check the components
1
The components included in the box may differ depending on your country.
Remove the protective tape and film covering the machine and the ink tank cover.
Watch our FAQ Videos for help
with setting up your Brother
machine.
support.brother.com/videos
2

Load paper in the paper tray

For more information about paper handling and sizes, see the Reference Guide.
Pull the paper tray completely
out of the machine.
Connect the
3
power cord
Connect the power cord and the
machine powers on automatically.
Follow the prompts displayed on the
LCD to set the date and time.
Push down on the cap of the ink
Point the nozzle upward so
tank to close it tightly. Repeat step
that the ink does not spill,
for the three other ink tanks.
and then remove the nozzle 4
from the ink tank.
Close the ink tank cover. The
machine will prepare the ink tube
system for printing.
Select your
7
language (if needed)
1.
Press Ajustes (Settings).
2.
Press a or b to select the following:
a. Select [Conf. inicial](Initial Setup), and then
press OK.
b. Select [Sel. idioma](Local Language), and
then press OK.
c. Select your language, and then press OK.
3.
Press Detener/Salir (Stop/Exit).
Starter Ink Bottles Quick Setup Guide
• Black
Product Safety Guide
• Yellow
• Cyan
• Magenta
USB Interface Cable
(For some countries)
Open the output paper tray
cover a. Fan the paper well and load it in the tray.
4
Fill the ink tanks with the starter ink
IMPORTANT
Check the ink bottle model name
on the label. Incorrect ink may
cause damage to the machine.
BK (Dye) CMY
BT5000CMY
BTD60BK BT5001CMY
BT5009CMY
DO NOT USE
Open the ink tank cover
BK (Pigment)
the tab
BT6000BK
cap of the ink tank.
BT6001BK
BT6009BK
5

Machine settings

When the machine has finished the initial cleaning
process, follow the steps on the LCD to configure the
machine settings.
• Check print quality
• Configure the tray settings
• Set Firmware Update Notice
• Print the installation sheet
Select the correct
8
Receive Mode
If you are not using your machine as a fax, go to
The correct Receive Mode is
determined by the external
devices and telephone subscriber
services (Voice Mail, Distinctive
Ring, etc.) you will be using on the
same line as the Brother machine.
For more information, see Choose
the Correct Receive Mode in the
Reference Guide.
The latest manuals are available at the Brother Solutions Center:
support.brother.com/manuals
Brother Installation Disc
Telephone Line Cord
Adjust the paper guides.
2
Remove the cap and protective
film from the ink bottle, and then
1
replace the cap.
and pull
a
NOTE
downwards to open the
b
Fasten the ink bottle cap tightly to
avoid leakage.
6
Connect the telephone line cord.
Use the jack marked LINE.
10 .
1.
Press Ajustes (Settings).
2.
Press a or b to select the
following:
a. Select [Fax], and then
press OK.
b. Select [Setup Receive],
and then press OK.
c. Select [Receive Mode],
and then press OK.
d. Select your Receive Mode,
and then press OK.
3.
Press Detener/Salir (Stop/
Exit).
NOTE
• The Reference Guide for this model is available on the enclosed installation disc.
• Save all packing materials and the box in case you must ship your machine.
• You must purchase the correct interface cable for the interface you want to
use. A USB cable is included for some countries.
USB cable
We recommend using a USB 2.0 cable (Type A/B) that is no more than 6 feet
(2 meters) long.
Ethernet (Network) cable
Use a straight-through Category 5 (or greater) twisted-pair cable for 10BASE-T or
100BASE-TX Fast Ethernet Network.
NOTE
Pull out the paper support a, and unfold
the paper support flap b so that the
printed pages do not fall.
Close the output paper tray cover, and
then slowly push the tray completely
into the machine.
Remove the tip of the ink bottle.
Insert the nozzle of the ink bottle
firmly so that the ink does not
spill. Fill the ink tank by gently
squeezing the bottle as shown.
Empty the entire bottle into the
ink tank.
Connect the telephone line cord
If you are not using your machine as a fax, go to
NOTE
If you are sharing one telephone line with an external
telephone, connect it as shown below. Before you
connect the external telephone, remove the white
protective cap c from the EXT. jack of the machine.
9

Set your Station ID

If you are not using your machine as a fax, go to
1.
Store your name and fax Press Ajustes (Settings).
number so the machine prints it
2.
Press a or b to select the following:
on all outgoing fax pages.
a. Select [Initial Setup],
For more information, see Enter
and then press OK.
Text on Your Brother Machine in
b. Select [Station ID],
the Online User's Guide.
and then press OK.
c. Select [Fax], and then
press OK.
3.
Enter your fax number (up to 20 digits),
and then press OK.
4.
Enter your name (up to 20 characters),
and then press OK.
5.
Press Detener/Salir (Stop/Exit).
MEX/LTN-ENG
Version A
7 .
1
2
3
a. Extension telephone
b. External telephone
c. Protective cap
10 .