C O N T E N T S 1. GENERAL NOTES 2. HOW DOES GAS BURNER OPERATE 3. COMPONENTS SPECIFICATION&ACCESSORIES 3.1 City gas accessories 4. TOOLS 5. REPAIR PROCESS 5.1 Remove the dirty oil from nozzle 5.2 Remove the gas valve 6.
1. GENERAL NOTES 1.1 Warning for models which connect to mains electrical power, before exposing any of the internal electrical wiring the appliance must be disconnected from electrical power by unplugging the service cord from the electrical outlet. For models which connect to battery power, before exposing any of the internal electrical wiring the appliance must be remove the battery also.
2. HOW DOES GAS BURNER OPERATE 1. Gas tank 2. Low pressure regulator (Safety warning: Do not use high pressure regulator) 3. Flexible rubber hose or copper tube 4. Elbow coupling gas with fibre washer (Warning: Do not use regular rubber washer) 5.
Gas from the tank (1) is released from the low pressure regulator (2) into the hose or tube (3), travelling pass the elbow coupling to the valve (4). To ignite the burner, press down and turn the safety valve (5) counter-clockwise simultaneously. This opens up the valve, letting the gas to the nozzle of the burner (6), and turns the ignition switch to on (7) at the same time.
4. TOOLS - Nut spinner No. 7 - Philip / Flat screw driver - Spanner No. 15 - Nozzle cleaner - Gas leak detector - Needle for dirty removal from nozzle 5. REPAIR PROCESS 5.1 Remove out the dirty oil from nozzle 1.
Page 8
By removing the hob the following parts are accessible for service or replacement. • Burner mounting cups. • Burner supply tubes. Note: When fitting the burner tubes to the valves and burner mounting cups the nuts should be fastened with a torque of 10-12Nm. •...
7. CONVERSION DETAILS The appliance is convertible between Natural Gas & LP. Procedure 1. Turn off gas supply to appliance. 2. Disconnect appliance from electrical power. 3. Remove the trivets and the burner caps & distributors. 4. Remove the existing injectors and replace with the injectors shown in the table below. 5.
Page 13
MODEL - ELECTROLUX EGG 7422S PARTS LIST REF # : H/A/333 CODE NO PART NAME UNIT (PCS) TH-0001/ED GLASS - 2 BURNER ( ELECTROLUX ) TH-0002/AB BOTTOM PLATE - 2 BURNER (Z) SABAF TH-0004/AZ IRON PIPE (2 BURNER) WITH FITTING (L:40.5) TH-0004/KH BRASS NUT HEX 14MM x M12 x 1.2...
Page 14
BIG ROUND CUSHION - NICKY TH-0020/AA CUT OUT DIE CUT PAD ( THH HOB) TH-0021/FE HOB LINER ELUX. NO MODEL - NICKY TH-0022/EA INST. MANUAL - ELECTROLUX EGG7422 & EGG 7432 TH-0023/BD REGULATOR STICKER BATTERY STICKER (ELUX HOB) TH-0023/BE TH-0023/IA...
Page 16
MODEL - ELECTROLUX EGG 7432S PARTS LIST REF # : H/A/332 CODE NO PART NAME UNIT (PCS) TH-0002/EF GLASS - 3 BURNER ( NICKY ) TH-0002/BC BOTTOM PLATE - 3 BURNER (Z) SABAF TH-0004/BZ IRON PIPE (3 BURNER) WITH FITTING (L:40.5) TH-0004/KH BRASS NUT HEX 14MM x M12 x 1.2...
Page 17
GUARANTEE CARD : ELECTROLUX TH-0020/AA CUT OUT DIE CUT PAD ( THH HOB) TH-0021/FE HOB LINER ELUX. NO MODEL - NICKY TH-0022/EA INST. MANUAL - ELECTROLUX EGG7422 & EGG 7432 REGULATOR STICKER TH-0023/BD TH-0023/BE BATTERY STICKER (ELUX HOB) TH-0023/IA GAS LEAKAGE WARNILNG SLIP...
Page 19
MODEL - ELECTROLUX EHG 7322X 76SS ETU PARTS LIST UNIT CODE NO PART NAME (PCS) TH-0008/NC SQ ENAMEL STAND(PAN)76SS ETU TH-0008/ND SQ ENAMEL STAND(WOK)76SS ETU TH-0001/CC TOP PLATE-2B-ETU-W/O HOLE TH-0006/ZA BURNER TRIPLE CROWN WOK CYCLIN TH-0006/ZB TRIPLE CROWN BODY WITH INJECTO...
Page 20
NUT HEX M4 [Blue Zink] 7mm TH-0005/UE BATTERY BOX COVER (ALSTAR) TH-0012/AA GAS HOB BASE LINING EH-0161/AB BURBLE SHEET:880 X 580 X 10MM H2-0202/CD GUARANTEE CARD: ELECTROLUX XH-0001/GA BATTERY STICKER (XINBAO HOB) TH-0019/AE HOB POLYFOAM-ELECTROLUX-NICKY TH-0019/DA TRIPLE CROWN TOP PACK FOAM TH-0020/AN...
Page 22
MODEL - ELECTROLUX EHG 7332X 76SS ETU PARTS LIST UNIT CODE NO PART NAME (PCS) TH-0008/NC SQ ENAMEL STAND(PAN)76SS ETU TH-0008/ND SQ ENAMEL STAND(WOK)76SS ETU TH-0001/CD TOP PLATE-3B-ETU-W/O HOLE TH-0006/ZA BURNER TRIPLE CROWN WOK CYCLIN TH-0006/ZB TRIPLE CROWN BODY WITH INJECTO...
Page 23
BURNER CAP SEMI RAPID GLOSS TH-0008/NE ROUND ENAMEL STAND(76SS ETU) TH-0012/AA GAS HOB BASE LINING EH-0161/AB BURBLE SHEET:880 X 580 X 10MM H2-0202/CD GUARANTEE CARD: ELECTROLUX XH-0001/GA BATTERY STICKER (XINBAO HOB) TH-0019/AE HOB POLYFOAM-ELECTROLUX-NICKY TH-0019/DA TRIPLE CROWN TOP PACK FOAM TH-0019/DD...
10. TROUBLE SHOOTING Fault Possible cause Remedy Burner will not light even -Gas supply valve turned off -Turn on gas supply to appliance though the spark plug is -Control knob not on -Turn knob on working -Wrong knob turned -Ensure the knob you are turning correspond to the burner you want to light -Port blockage in ignition...