Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for HATO 400Y
Summary of Contents for HATO 400Y
- Page 1 HATO 400Y HEL 11C SLIDING GATE OPERATOR USER’S MANUAL...
-
Page 2: Outline
OUTLINE 1. Important safety information………………………3 2. Main technical parameters ………………………3 3. Installation …………………………………………3 4. Connecting …………………………………………7 5. Control ……………………………………………10 6. Check ……………………………………………14 7. Maintenance………………………………………14 8.Troubleshooting …………………………………15... - Page 3 -20ºC~+50ºC 3. Installation The HATO 400 Y rack-driven gate operator operates by forcing a drive rack past a drive gear. The entire configuration is shown in Fig.1. The gate operator must be installed on the inside of the gate. Gate preparation Be sure the gate is properly installed and slides smoothly before installing the DKC400Y sliding gate operator.
-
Page 4: Anchors
Fig.1 Concrete pad The base unit of the gate operator requires a concrete pad in order to maintain proper stability. The concrete pad should be approximately 300mm x 200mm x 200mm deep in order to provide for adequate operation. Anchors You can use the anchors, bolts, washers and nuts that are provided with the operator. - Page 5 Fix the three nuts (in the same package with rack) on the rack element. Lay the first piece of rack on the gear and weld the first nut on the gate. Move the gate manually, checking if the rack is resting on the gear, and weld the second and third nut. ...
- Page 6 Rack Fig.5 CONFORMITY DECLARATION: Motor Hato 400Y meets the requirements set out in the following provisions: It’s in accordance with Machine Directive 2006/42/WE and following modify. It’s in accordance with the following directive CE: Electromagnetic compatibility Directive EMC 2014/30/UE and following modify.
- Page 7 Controller of Gate Drives for 230Vac 500W Motors USER’S MANUAL...
- Page 8 SOFTWARE MARKING NOTES 1.2.0-C-NO HEL11C 11:8.2.2/6.1.0 Before the installation and first use of the controller read the manual carefully and keep it for future reference. According to the Machinery Directive 2006/42/CE, the product must not be put into service until the final machinery into which it is to be incorporated or of which it is to be a subassembly has been declared in conformity with the provisions of directives and relevant regulations which the final machinery must comply with.
-
Page 9: Table Of Contents
Version : HEL11C • – cooperates with Hato’s transmitters operating at a 433.92 MHz frequency and compatible with Keeloq protocol. • – with encoder input • – lamp control by relay Table of contents: OUTLINE ......................................2 Anchors ......................................4 1. -
Page 10: Application And Functionality Of Hel11C
1. Application and functionality of HEL11C The controller is designed for gate drives with 230Vac motors. A perfect choice for continuous operation, the controller can be used in community car parks, private homes and corporate compounds. Applied Microchip rolling code technology prevents from not authorized entrance. -
Page 11: Step-By-Step Pushbutton Connection
command after powering up is “open”. Press the SBS or programmed transmitter button. If drive works in closing 2.4 Step-By-Step pushbutton connection direction stop the motor, switch off the power supply and Connect the SBS pushbutton using 2x 0,5mm wire which switch motor’s leads connected to the inputs OPEN(10) parameters are according to regulations: CEI 20-22;... -
Page 12: Autoclose Time Setting
necessitates photocells to ensure user safety (to prevent 4. Transmitters deleting and gate from closing when an obstacle is within its range!). in addition, the photocells will reduce the opening time. The programming controller will detect the passage of a vehicle and will close the gate after 5 seconds. - Page 13 Tab.1.1. Autoclose time setting (e.g.) 1. Press the LEARN button. The LED will light up. Release the button. LEAR LEAR 2. Then, by pressing the same button you can set the delay time. One keystroke corresponds to 15 seconds, (e.g. 4 keystrokes mean 1 minute; the LED dims at each keystroke).
-
Page 14: Technical Specification
< 25mA AC Powe consumption in standby: < 10 W Transmitters range: <200m Frequency: 433,92MHz Transmitters type: Version HATO Keeloq Transmitters memory: 40 pcs Autoclose max time: 5s - 10min Operation max time: 120 sec. Operating temperature: -20ºC +70ºC Fuse type: 5A/230V, ø5x20... -
Page 16: Controller Wiring Diagram
HATO 400Y SLIDING GATE OPERATOR USER’S MANUAL 7. Controller wiring diagram Picture 2... - Page 17 HATO 400Y SLIDING GATE OPERATOR USER’S MANUAL DISTRIBUTOR/SALESMAN Hato Polska S.C Tomasz Słodkowski – Harmeet Singh ul. Tunelowa 57 40-676 Katowice POLAND Warehouse/sales/service ul. Żeromskiego 1 41-205 Sosnowiec tel. 032/ 785-25-42 www.hato.com.pl...
Need help?
Do you have a question about the 400Y and is the answer not in the manual?
Questions and answers
Dobrý den. Potřebuji poradit. Jak Mám nastavit koncovou polohu pro zavírání a koncovou polohu pro otvírání. Žádné automatické zavírání zakazník nepotřebuje ani rychlost postačí pomalu ale chce jenom polohu zavřeno a polohu otevřeno. Děkuji
The end positions for closing and opening on the HATO 400Y are set using the spring limit switches. These switches ensure that the gate stops at the correct position when fully opened or closed. Proper alignment of the limit switch, block, and rack is necessary to meet the required positioning. Ensure that the installation follows the manual's instructions for correct setup and adjustment.
This answer is automatically generated