Table of Contents
Related Manuals for SMART-AVI NET-IP-PRO
Summary of Contents for SMART-AVI NET-IP-PRO
- Page 1 NET-IP-PRO User Manual Web-Based Control for Smart-AVI Products Remotely control Smart-AVI product operations over a local area network or via the Internet from anywhere in the world Made in U.S.A. www.SmartAVI.com 1-800-AVI-2131...
-
Page 2: Table Of Contents
Connecting to the NET-IP-PRO Initial Setup Controlling the NET-IP-PRO via HTTP — Matrix Menu Controlling the NET-IP-PRO via HTTP — Macros Controlling the NET-IP-PRO via HTTP — Device Configuration Menu Controlling the NET-IP-PRO via TELNET Upgrading the NET-IP-PRO Limited warranty statement WHAT'S IN THE BOX? PART NO. -
Page 3: Introduction
INTRODUCTION The NET-IP-PRO is an RS-232 control module that allows most SmartAVI switching matrixes to be controlled remotely via HTTP or TELNET. Manage the switching functions of your matrix with ease from anywhere in the world. With the NET-IP-PRO you can save up to 10 preset input/output configurations for easy access. -
Page 4: Connecting To The Net-Ip-Pro
1. Power off all devices. 2. Using a CAT5 cable, connect the NET-IP-PRO to your local network. 3. If you have a smart-AVI device use an RS-232 male to male cable to connect the NET-IP-PRO to your smart -AVI device. -
Page 5: Initial Setup
INITIAL SETUP Once connected to the NET-IP-PRO, you will see the following menu of options (Figure 5-1): Administration Device Config Matrix Network Settings Users Update Firmware Web Console Web Telnet Logout Figure 5-1 For the initial setup, click the “Network Settings” tab and manually assign an IP address to the NET-IP-PRO. - Page 6 Figure 6-1 Figure 6-2 You can access the NET-IP-PRO to control your Smart-AVI Matrix on your local area network (LAN) as shown in figure 6-2 or from anywhere in the world via the internet.
-
Page 7: Controlling The Net-Ip-Pro Via Http - Matrix Menu
CONTROLLING THE NET-IP-PRO VIA HTTP Matrix Menu The Matrix menu (figure 7-1) al- lows you to set the cross-points for the matrix. Cross-points are used to route signals from the individual input (signal source) to individual outputs (displays). The output channels can only have one input, but each input can have several outputs. -
Page 8: Controlling The Net-Ip-Pro Via Http - Macros
CONTROLLING THE NET-IP-PRO VIA HTTP (Continued) MACROS Record this setup as macro: allows you to save and recall cross-point configurations with the push of a but- ton. To setup a Matrix Macros preset, you must do the following steps: 1. Click on the matrix window to set a cross point; set as many cross points as needed. This will instantly set the input to the corresponding output as indicated in the matrix. -
Page 9: Controlling The Net-Ip-Pro Via Telnet
Hyperterminal or PuTTY (see figure 9-1) to connect to the IP address of the NET-IP-PRO. You will be prompted for a username and password. This will be the same as the login infor- mation via HTTP. -
Page 10: Limited Warranty Statement
Smart-AVI limited warranty is valid in any country where the covered product is distributed by Smart-AVI. Limitations of warranty To the extant allowed by local law, neither Smart-AVI nor its third party suppliers make any other warranty or condition of any kind whether expressed or implied with respect to the Smart-AVI product, and specifically disclaim implied warranties or conditions of merchantability, satisfactory quality, and fitness for a particular purpose. - Page 11 NOTICE The information contained in this document is subject to change without notice. SmartAVI makes no war- ranty of any kind with regard to this material, including but not limited to, implied warranties of merchant- ability and fitness for particular purpose. SmartAVI will not be liable for errors contained herein or for inci- dental or consequential damages in connection with the furnishing, performance or use of this material.
Need help?
Do you have a question about the NET-IP-PRO and is the answer not in the manual?
Questions and answers