Table of Contents
Advertisement
Quick Links
CENTURY COLOUR
2500L
PR-2001
This product manual contains important information about the safe installation
and use of this projector. Please read and follow these instructions carefully
and keep this manual in a safe place for future reference.
PR LIGHTING LTD.
No. 571, Yingbin Road, Dashi Panyu, Guangzhou, 511430 China
http://www.pr-lighting.com
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Pure Reliability CENTURY COLOUR 2500L PR-2001
Summary of Contents for Pure Reliability CENTURY COLOUR 2500L PR-2001
- Page 1 CENTURY COLOUR 2500L PR-2001 This product manual contains important information about the safe installation and use of this projector. Please read and follow these instructions carefully and keep this manual in a safe place for future reference. PR LIGHTING LTD. No.
-
Page 2: Table Of Contents
INDEX SECTION PAGE SAFE USAGE OF THE PROJECTOR CONSTRUCTION FITTING THE LAMP POWER SUPPLY – MAINS OPERATION STAND-ALONE MODE XLR CONNECTIONS AND TERMINATOR MASTER/SLAVE MODE CONTROLLER MODE - DMX OPERATION DMX CONTROL CHANNEL FUNCTIONS MAINTENANCE KEEPING THE PROJECTOR CLEAN TROUBLESHOOTING TECHNICAL DATA ELECTRICAL DIAGRAM COMPONENT ORDER CODES... -
Page 3: Safe Usage Of The Projector
SAFE USAGE OF THE PROJECTOR The following points are important for safety as well as for the smooth installation and performance of the unit. When unpacking and before disposing of the package check there is no transportation damage before using the projector. Should there be any damage caused by transportation, consult your dealer and do not use the unit. -
Page 4: Construction
CONSTRUCTION FITTING THE LAMP Position the projector-head in vertical position and lock it via the locking knobs. Remove the projector-head cover by loosening the 4 retaining-clips. Open the dichroic-colour-filter bracket by undoing the 2 M4 knurled-screws. Insert the lamp in the lamp-holder, and ensure the little bubble on the lamp is at a right angle (90°) to the beam path. -
Page 5: Operation
OPERATION When the power is switched on, the projector automatically starts to run the programmes of self test. After finishing these, the projector is ready for operation. Remove the cover of the control panel, you will see the DIP switches with numbers from 1 to 4, 3 rotary DIP switches for setting the start address and an LED display as shown in the figure below. -
Page 6: Xlr Connections And Terminator
XLR CONNECTORS AND TERMINATOR XLR CONNECTORS Connection between controller and projector and between one projector and another must be made with 2 core screened cable, with each core having at least a 0.5mm diameter. Connection to and from the projector is via cannon 3-pin XLR plugs and sockets which are included with the projector. -
Page 7: Master/Slave Mode
MASTER/SLAVE MODE Many luminaires can run synchronously by linking them with each other in the master/slave mode. Select one luminaire as the master, and set the DIP switches as shown in the figure below. Regard the other luminaires as the slaves, and set their DIP switches as shown in the figure below. - Page 8 REMOTE RESET CONTROL In controller mode, set the DIP switches as shown in the figure on the right, the channel 7 will be actived. Now, all the luminaires will work under remote reset control. 8/14 Century Colour 2500L EN.doc...
-
Page 9: Dmx Control Channel Functions
DMX CONTROL CHANNEL FUNCTIONS The Century Colour has 7 channels. They are shown in the following table. ITEM CHANNELS PERCENTAGE DESCRIPTION VALUE 0-63 0%-25％ Slow speed Motor speed 64-127 25%-50% Medium speed adjust 128-191 50%-75% Medium to high speed 192-255 75%-100% High speed White to cyan continuous... - Page 10 DMX START ADDRESS SETTING VIA THE 3 ROTARY DIP SWITCHES Each Century Colour 2500L must be given a DMX start address so that the correct projector responds to the correct control signals. This DMX start address is the channel number from which the projector starts to “listen”...
-
Page 11: Maintenance
MAINTENANCE If the lamp becomes damaged or deformed in any way it must be replaced. If the light from the lamp appears dim this would normally indicate that it is reaching the end of its life and it should be changed at once, old lamps run to the extremity of their life can explode. If the projector does not function, check the fuse in the projector base, it should only be replaced by the same specified value. -
Page 12: Technical Data
TECHNICAL DATA Power supply: 230V AC 50Hz Optional: 240V, 220V AC 50/60Hz Power consumption: 2800W at 220V Lamp: MSA2500 DE, double ended Colour temperature: 5600°K Manufacturers Rated Lamp life: 2000 Hours Protocol: Standard DMX 512 Running mode: Stand-alone, Master/Slave, and DMX Controller DMX channels: 7 channels Colours:... -
Page 13: Electrical Diagram
ELECTRICAL DIAGRAM 13/14 Century Colour 2500L EN.doc... -
Page 14: Component Order Codes
COMPONENT ORDER CODES NAME PART NO. QUANTITY REMARK TRANSFORMER 040030022 200V/220V/50Hz IGNITOR 040090004 230V/50Hz BALLAST 040070033 230V/50Hz RELAY 192010009 230V/20A FILTER 193020001 THERMOSTAT 190010054 95℃/10A THERMOSTAT 190010035 120℃/16A FUSE 270041008 RT14-20A 030060022 230V/22W LAMP 100050024 MSA 2500 DE CAPACITOR 140010018 60µF/AC 370V MOTOR 030040029...
Need help?
Do you have a question about the CENTURY COLOUR 2500L PR-2001 and is the answer not in the manual?
Questions and answers