Table of Contents
Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Challenge Xtreme M1Q-DD4-80
Summary of Contents for Challenge Xtreme M1Q-DD4-80
- Page 1 800W JIGSAW WITH LASER M1Q-DD4-80 ORIGINAL INSTRUCTIONS...
-
Page 2: General Power Tool Safety Warnings
Unmodified plugs and satisfaction out of this tool. matching outlets will reduce risk of electric Your M1Q-DD4-80 Jigsaw is suitable for making straight, curved and miter cuts on shock. squared work pieces made of plastic, wood •... - Page 3 ORIGINAL INSTRUCTIONS • Do not use the power tool if the • Use personal protective equipment. On/Off switch does not work! Always wear eye protection. Any power tool that cannot be controlled Protective equipment such as dust mask, with the switch is dangerous and must be non-skid safety shoes, hard hat, or hearing repaired.
- Page 4 ORIGINAL INSTRUCTIONS • Do not use blunt or damaged blades. Bent This will ensure that the safety of the blades can break easily or cause kickback. power tool is maintained. • When removing the blade from the tool ADDITIONAL SAFETY avoid contact with the skin and use proper RULES FOR YOUR protective gloves when touching the blade...
- Page 5 ORIGINAL INSTRUCTIONS SYMBOLS Safety warnings for lasers This power tool produces class 2 To reduce the risk of injury, user must read instruction manual laser beams according to IEC EN 60825-1. Directly looking into the laser beam – particularly with magnifying Warning devices such as binoculars –...
- Page 6 ORIGINAL INSTRUCTIONS Pic A HELPLINE NO 08454 505299...
-
Page 7: Component List
ORIGINAL INSTRUCTIONS COMPONENT LIST 1 Lock button 10 Laser/ light switch 2 Trigger switch 11 Quick-action chuck 3 Ventilation openings 12 Safety Guard 4 Dust port 13 Saw blade 5 Allan key holder 14 Switch for sawdust extraction device 6 Base plate 15 Locking screws for parallel guide 7 Pendulum action switch 16 Guide holes for parallel guide... -
Page 8: Technical Data
ORIGINAL INSTRUCTIONS TECHNICAL DATA Voltage 230-240V~50Hz Power 800W Rated speed 0-3000/min Max. cutting capacity Wood 80mm Steel Bevel capacity ±45° Pedulum position Protection class NOISE INFORMATION A weighted sound pressure 94dB(A) A weighted sound power 105dB(A) & K 3dB(A) Wear ear protection when sound pressure is over 80dB(A) VIBRATION INFORMATION Vibration total values (triax vector sum) determined according to EN 60745:... - Page 9 ORIGINAL INSTRUCTIONS WARNING: The vibration emission value during actual use of the power tool can differ from the declared value depending on a number of variables including How the tool is used and the materials being cut or drilled. The tool being in good condition and well maintained. To use the correct accessory for the tool and ensuring it is sharp and in good condition.
-
Page 10: Removing Blade
ORIGINAL INSTRUCTIONS ASSEMBLY 2) Removing blade CAUTION! To prevent personal injury, WARNING! Blades can get very hot always disconnect plug from power during use. Avoid direct contact with source before assembling parts, making the saw blade and let it cool down first. adjustments, or changing blades and observe the general safety guidelines. -
Page 11: Getting Started
ORIGINAL INSTRUCTIONS GETTING STARTED • 1 x press: Laser • 2 x press: LED work light On/Off Switch • 3 x press: Laser beam combining with LED Switching on: work light Press the trigger switch (2) • 4 x press: switched off Continuous operation: Adjusting the cutting speed: Squeeze the trigger switch and depress the... - Page 12 ORIGINAL INSTRUCTIONS Adjusting the Pendulum Stroke The pendulum action can be adjusted with the pendulum action switch (7), even during operation. Set the pendulum action switch (7) on one of the following positions: Position 0 = No oscillation Material: rubber, ceramic, aluminum, steel Note: For fine materials and clean cut, thin materials (sheets) Sawdust Extraction device...
-
Page 13: Plunge Cutting
ORIGINAL INSTRUCTIONS Switch on the jigsaw until it reaches full speed. CUTTING GUIDANCE Then the blade goes forwards slowly along the cutting line while applying light pressure Standard cutting on the saw. When using the laser guide for cutting ensure that the laser is on Parallel cutting and lines up with the groove marked Make sure that the plug is disconnected from... -
Page 14: Cutting Metal
ORIGINAL INSTRUCTIONS • When the base plate 6 fully lays on the work-piece, continue sawing along the desired cutting line. Cutting metal When sawing metal, coolant/lubricant should be applied alongside cutting line to ensure the blade remains cool. TROUBLE SHOOTING Jigsaw has no power •... -
Page 15: Plug Replacement
ORIGINAL INSTRUCTIONS PLUG REPLACEMENT Your Power Tool is supplied with a fitted plug, however if you need to fit a new plug follow the instruction below. IMPORTANT The wires in the mains lead are coloured in accordance with the following code: Blue - Neutral Brown –... -
Page 16: Ec Declaration Of Conformity
We hereby certify that the product stipulated above complies with all the relevant provisions of the following EC new approach directive/s. This declaration of conformity is issued under the sole responsibility of the manufacturer 800W Jigsaw With Laser M1Q-DD4-80 Type of Product: Model Number:...
Need help?
Do you have a question about the M1Q-DD4-80 and is the answer not in the manual?
Questions and answers