Cleaning And Maintenance - Espressione Squissita Intelligent CE-4492 Manual

3. Press the ON/OFF button (1) The luminous indicator
(1) will flash blue.
Once it stops flashing:
4. Press the coffee outlet button (2/2) The pump will
begin to operate. The water will start to come out through
the coffee outlet.
5. Allow the water to circulate for a few seconds. The
coffee maker is now ready for use.
Switching on
1. Fill the tank with cold water. The tank (14) can be
removed via the back of the coffee maker or open the lid
(13) and pour the water in directly.
2. Plug the appliance into the mains.
3. Press the ON/OFF button (1) The luminous indicator
(1) will flash blue.
The luminous indicator on the ON/OFF button (1) will
stay a fixed blue when it has reached working tempera-
ture and is ready to brew coffee.
During the heating cycles the blue light will flash again
and will not permit coffee to be brewed.
We recommend placing the cups on top of the cup war-
mer tray (9) so that they warm up during this operation
and ensure a better cream in the coffee.
Brewing the coffee
1. Place the filter that you wish to use, 1 or 2 cups (5, 6)
into the filter holder (4)
2. Use the scoop (17) to measure in the coffee. Press
the coffee down as per taste.
One scoop represents the recommended amount for
one cup.
3. If you wish to use coffee capsules, follow the instruc-
tions given below:
A. Open the unit measure bag. Place the capsule filter
(7) into the filter
holder (4). Place the capsule into the filter holder.
4. Put the filter holder (4) into the coffee maker.
B. Make sure that the filter holder is securely closed, pus-
hing the handle from left to right, otherwise it may drip.
5. Place one or two cups below the coffee outlet holes (8).
Coffee extraction (brew)
If you want your first coffee to be hotter, fit the filter
holder without coffee and allow one or two cups of hot
water to come out, this will heat up the coffee maker
components.
1. Press button (2 or 3) depending on whether you want
1 or 2 cups. The luminous indicator on the corresponding
button will light up
C: 2. The coffee will begin to come out for the program-
med time.
During the brewing cycle the luminous indicator on the
selected button will flash and remain fixed when brewing
has finished.
3. If you wish to stop the brewing cycle before time,
press the corresponding button again. Brewing will stop.
Automatic pre-brewing function
After selecting the brew cycle, the coffee maker injects
a little water to moisten the ground coffee just before
brewing, which improves the aroma. This also helps
to pack the ground coffee tighter to produce a brew at
higher pressure, improving the quality of the coffee and,
in short, the cream.
Changing preset brew times
1. Press the corresponding button (1 or 2 cup) for 3
seconds, the coffee will come out when you release the
button.
2. Press the corresponding button (1 or 2 cup) again and
the coffee will stop coming out. The coffee outlet time will
remain programmed for subsequent brews.
The amount of coffee needed for 1 or 2 cups may vary
from brew to brew depending on the type of coffee used
and how tight it is packed.
Nevertheless, the programmed brewing times will remain
constant.
Resetting preset brew times
1. Press the two buttons (2 and 3) at the same time for 3
seconds. The ON/OFF luminous indicator will flash once.
Then it will remain on fixed blue. The preset brewing
values have now been re-established.
Cleaning
• If you have used ground coffee, clean out the grounds
by placing the filter holder under a running tap.
• If you have used a capsule, remove it and put it in the
rubbish.
B. STEAM D
To avoid possible burns always handle the steam nozzle
(10) by the protector (11).
To heat any type of liquid using the steam nozzle (10).
1. Place the cup containing the liquid to heat below the
steam nozzle.
2. Set the steam nozzle control (15) to the "Preheating"
position D1.
The ON/OFF luminous indicator (1) will flash blue and
then remain fixed blue when the steam nozzle is ready
for use.
3. Insert the steam nozzle (10) into the liquid to heat and
gradually open the steam nozzle control (15), to "Fully
open" if you wish D2 .
At the beginning a little water will come out. If you wish,
you can use an empty container to catch this water
before inserting the steam nozzle into the liquid you want
to heat.
If the steam loses pressure, set the steam nozzle control
(15) to the "Preheating" position .
Wait until the ON/OFF luminous indicator (1) remains lit.
Repeat these steps as many times as necessary.
4 Set the steam nozzle control (15) to the "Closed" posi-
tion when you have finished using it.
5 When you have finished, clean away any waste matter
that may have got inside it.
To do this:
Place an empty container below the steam nozzle and
open the steam nozzle control (15) to allow steam to exit.
The maximum time for steam production is 2 minutes.
AUTO OFF
If, after 30 minutes, the machine is not used it will switch
itself off. All of the luminous indicators will switch off.

4 CLEANING AND MAINTENANCE

9