CONFIDENTIAL 1 Precautions Follow these safety, servicing and ESD precautions to prevent damage and to protect against potential hazards such as electrical shock. 1-1 Safety Precautions 1-1-1 Warnings For continued safety, do not attempt to modify the (READING SHOULD circuit board. NOT BE ABOVE 0.5mA) Disconnect the AC power and DC Power Jack before servicing.
CONFIDENTIAL 3 Disassembly and Reassembly This section of the service manual describes the disassembly and reassembly procedures for the MO15E* monitors. WARNING: This monitor contains electrostatically sensitive devices. Use caution when handling these components. 3-1 Disassembly Cautions:1. Disconnect the monitor from the power source before disassembly. 2.
CONFIDENTIAL 4 Troubleshooting Notes: 1. Before troubleshooting, setup the PC’s display as below. • Resolution: 1024 x 768 • H-frequency: 48 kHz • V-frequency: 60 Hz 2. If no picture appears, make sure the power cord is correctly connected. 3. Check the following circuits. •...
Page 25
CONFIDENTIAL 6 Electrical Parts List 6-2 Others Loc. No. Code No. Description Specification Remarks BN90-00304A ASSY COVER FRONT MO15PS BN90-00053B ASSY COVER FRONT MO15PS,ABS HB,BK07,ANALOG BN90-00305A ASSY COVER REAR MO15PS BN90-00054B ASSY REAR MO15ES,ABS HB BK07 BN90-00306A ASSY STAND MO15PS BN90-00056B ASSY STAND MO15PS,ABS HB,BK07,ANALOG...
Page 26
CONFIDENTIAL 5 Exploded View & Parts List Memo MO15E*...
Page 27
CONFIDENTIAL 4 Troubleshooting 4-2 No Video Power indicator is green. Does the H-sync Does the clock pulse Does the pulse appear pulse appear at appear at Pin 78 of IC300? at Pin 8 of IC501? Pin 38, 39 of IC300? Replace X501 or Does the clock pulse check its related circuit.
Page 29
CONFIDENTIAL 4 Troubleshooting 4-3 No OSD There is video but no OSD. Press exit key for more than 5 seconds to do the factory preset. While pushing a front control Do the pulses appear at Pin2 button, does any pulse appear and Pin3 of CN600 while pushing a front control button? at Pin 16, 17 of IC501?
Page 30
CONFIDENTIAL 3 Disassembly and Reassembly 4. Remove 2 flat head screws on the hinge mounting. Do not remove the screw for cable clamp. 5. Disconnect the stand cable from socket and remove stand assembly. 6. Remove 2 screws of Cover Rear. 7.
Page 31
CONFIDENTIAL 3 Disassembly and Reassembly 9. Remove the 4 screws of panel. 10. Turn the monitor for face down and open the Cover Rear from top area. 11. Disconnect the function cable from the connector of main board. 12. Remove the 3 screws of shield. MO15E*...
Page 32
CONFIDENTIAL 3 Disassembly and Reassembly 3-2 Replacement Order of Lamp Assemblies 1. After confirm there is nothing on the disk Turn the LCD module over and put it on a flat desk set to the ground. 2. Remove the screw and slide the lamp unit.
Page 33
CONFIDENTIAL 3 Disassembly and Reassembly 4. Please fix the new lamp units on the LCD module : opposite process 2 and 3 Replacement of lamp unit should be done at the power off state and recommanded clean bench condition. 3-3 Reassembly Reassembly procedures are in the reverse order of Disassembly procedures.
Page 34
CONFIDENTIAL 3 Disassembly and Reassembly Memo MO15E*...
CONFIDENTIAL 2 Product Specifications 2-2 Pin Assignments Sync 15-Pin Signal Cable Connector Type Separate Composite Sync-on-green Pin No. Green Green Green + H/V Sync Blue Blue Blue GND (DDC Return) GND (DDC Return) GND (DDC Return) GND-R GND-R GND-R GND-G GND-G GND-G GND-B...
CONFIDENTIAL 2 Product Specifications 2-3 Timing Chart This section of the service manual describes the timing that the computer industry recognizes as standard for computer-generated video signals. Table 2-1 Timing Chart Mode VESA VGA1/70 Hz VGA3/60 Hz VGA2/70 Hz 640/72 Hz 800/60 Hz 640/75 Hz 800/56 Hz...
Page 37
CONFIDENTIAL 2 Product Specifications Table 2-1 Timing Chart Continued Mode VESA 640/67 Hz 832/75 Hz 1024/60Hz 1024/70Hz 1024/75Hz 800/72 Hz 800/75 Hz 1024x768 1024x768 1024x768 640 x 480 832 x 624 800 x 600 800 x 600 Timing fH (kHz) 35.000 49.726 48.077...
CONFIDENTIAL 1 Precautions 1-2 Servicing Precautions WARNING: An electrolytic capacitor installed with the wrong polarity might explode. Caution: Before servicing units covered by this service manual, read and follow the Safety Precautions section of this manual. Note: If unforeseen circumstances create conflict between the following servicing precautions and any of the safety precautions, always follow the safety precautions.
Page 39
Samsung Electronics Co.,Ltd. 416, Maetan-3Dong, Paldal-Gu, Suwon City, Kyungki-Do, Korea. Printed in Korea P/N : BN81-00034C-00 http://www.samsungmonitor.com (SyncMaster Worldwide) http://www.samsung-monitor.com (SyncMaster USA) http://www.sec.co.kr/monitor (Korea)