Subscribe to Our Youtube Channel
Related Manuals for SGS SPI1000
Summary of Contents for SGS SPI1000
- Page 1 INVERTER GENERATOR OWNER’S MANUAL FOR YOUR SAFETY PLEASE READ THESE INSTRUCTIONS CAREFULLY AND RETAIN THEM FOR FUTURE USE.
-
Page 2: Generator Safety
In emergency, switch engine switch to ‘off’. Always operate on level ground! If in doubt about anything, contact us on (+44) 01332 576850. Always consult this manual for effective product knowledge. WWW.SGS-ENGINEERING.COM PAGE 2 CALL FOR ASSISTANCE: 01332 576 850... -
Page 3: Exhaust Gas Precautions
EXHAUST GAS PRECAUTIONS Exhaust fumes can be fatal! • Always ensure that there is adequate ventilation when using the generator. • Always position the generator so that the exhaust is point- ing away from people or animals. • Never use the generator indoors or in an enclosed area. (i.e workshop, garage, lockup etc) EARTHING THE GENERATOR •... - Page 4 INVERTER GENERATOR COMPONENTS LOCATION DIAGRAM Status Choke display selector panel toggle protector Engine selector switch Earthing 12v battery point Output charging Economy socket point mode switch WWW.SGS-ENGINEERING.COM PAGE 4 CALL FOR ASSISTANCE: 01332 576 850...
- Page 5 INVERTER GENERATOR COMPONENTS LOCATION DIAGRAM Carrying Engine Fuel handle access tank panel Pull Fuel start on/off selector PAGE 5...
- Page 6 4. Screw the oil plug back in. 3. Insert the included funnel, Replace the side panel too. and fill the oil plug with 10w30 oil, till the funnel container is empty. WWW.SGS-ENGINEERING.COM PAGE 6 CALL FOR ASSISTANCE: 01332 576 850...
- Page 7 FILLING THE INVERTER GENERATOR WITH PETROL FUEL Always use clean, unmixed, unleaded petrol fuel only in this inverter generator. 1. Unscrew the fuel filler cap to open. 2. Fill with unleaded petrol 3. Screw fuel filler cap fuel until at least 3/4 full. closed.
- Page 8 ‘on’. 3. Ensure the choke is pulled 4. Switch the engine switch out, this is the ‘start’ to the ‘on’ position. position. WWW.SGS-ENGINEERING.COM PAGE 8 CALL FOR ASSISTANCE: 01332 576 850...
-
Page 9: Operating The Generator
STARTING THE INVERTER GENERATOR 5. Pull the starter cord 6. Once inverter generator lightly, until it tenses- then engine starts, push in choke. pull briskly. This is the ‘running’ position for the choke. OPERATING THE GENERATOR 1. Start the engine and allow to run for a few minutes in order for it to warm up. - Page 10 3. Switch the engine switch 4. Turn the fuel tap so it is to the ‘off’position. pointing ‘left’ for the ‘off’ position. WWW.SGS-ENGINEERING.COM PAGE 10 CALL FOR ASSISTANCE: 01332 576 850...
- Page 11 INVERTER GENERATOR TROUBLESHOOTING PAGE 11...
- Page 12 If the pull start mechanism feels too ‘slack’ (i.e easy to pull), there may be not enough compression in the genera- tor engine for it to work properly. Please contact SGS Engineering. Engine making “revving” • If your generator is ‘hunting’ (surging), sounds.
- Page 13 MAINTENANCE SCHEDULE MATRIX PAGE 13...
-
Page 14: Maintenance Instructions
• Replace the filter into its origi- nal position and replace and secure the cover. WWW.SGS-ENGINEERING.COM PAGE 14 CALL FOR ASSISTANCE: 01332 576 850... - Page 15 • Lift out the fuel filter. • Clean the filter with solvent. If the filter is damaged, contact SGS Engineering. • Replace the filter and fuel cap. WARNING: DO NOT SMOKE AND/ OR HAVE ANY NAKED FLAMES DURING THIS PROCESS...
- Page 16 SGS Engineering (UK) Ltd West Side Park Raynesway Derby, DE21 7AZ EC Declaration of Conformity This is an important document and should be retained MANUFACTURER’S NAME: SGS Engineering (UK) Ltd Inverter Generator TYPE OF EQUIPMENT: SPI1000 PART NUMBER: APPLICATION OF EC COUNCIL DIRECTIVES / STANDARD:...
Need help?
Do you have a question about the SPI1000 and is the answer not in the manual?
Questions and answers