Subscribe to Our Youtube Channel
Related Manuals for SMC Networks C(D)U Series
Summary of Contents for SMC Networks C(D)U Series
- Page 1 Doc. no. ＣＵ＊＊－ＯＭ０００２Ｅ－Ａ PRODUCT NAME FREE MOUNT CYLINDER MODEL/ Series Ｃ(D)U SERIES Ｃ(D)UK SERIES Ｃ(D)UW SERIES Ｃ(D)UKW SERIES...
-
Page 2: Table Of Contents
1/10 Contents Safety Instructions 1. Specifications 2. Installation and Handling 3. Maintenance 4. Basic Circuit for Cylinder Operation 5. Troubleshooting No. ＣＵ＊＊－ＯＭ０００２Ｅ―Ａ... -
Page 3: Safety Instructions
2/10 Free Mount Cylinder / Series CU Safety Instructions These safety instructions are intended to prevent hazardous situations and/or equipment damage. These instructions indicate the level of potential hazard with the labels of “Caution,” “Warning” or “Danger.” They are all important notes for safety and must be followed in addition to International Standards (ISO/IEC), Japan Industrial Standards (JIS)*1) and other safety regulations*2). - Page 4 3/10 Free Mount Cylinder / Series CU Safety Instructions Caution The product is provided for use in manufacturing industries. The product herein described is basically provided for peaceful use in manufacturing industries. If considering using the product in other industries, consult SMC beforehand and exchange specifications or a contract if necessary.
-
Page 5: Specifications
4/10 1. Specifications 1-1. Specifications φ6 φ10 φ16 φ20 φ25 φ32 Bore size Fluid M5x0. 8 Port size Rc1/8 Max. operating pressure 0. 7Mpa 1. 05MPa Proof pressure Without switch: -10 to +70 ℃ (No freezing) Ambient and operating With switch: -10 to +60 ℃ (No freezing) fluid temperature 50 to 500mm/s Piston speed... - Page 6 5/10 b) Double acting double rod type [C(D)U(K)W*-*D] Operating pressure Mpa Pressure receiving area Bore size Rod O.D. (mm) (mm) 0. 3 0. 5 0. 7 φ6 21. 2 6.36 10.6 14.7 φ10 19.8 46.2 φ16 51.6 φ20 79.2 φ25 φ32 c) Spring retracted type [C(D)U(K)*-*S] Operating pressure Mpa...
-
Page 7: Installation And Handling
6/10 2. Installation and Handling ⑧ Consider emergency stop. 2-1 Design Design the system to prevent injury to personnel and damage to machinery and equipment when it is stopped by a safety device for a ！ Warning power outage or manual emergency stop. ①... - Page 8 7/10 2-5 Lubrication 2-3 Mounting Caution Caution ① Be sure to connect the piston rod and the ① Lubrication of non-lubricating cylinder load that their axial centers The product has been lubricated for life at the time of manufacture, and movement directions match.
- Page 9 8/10 2-10 Precautions 2-8 Maintenance Caution Warning ① Do not place your fingers in the clearance between ① Maintenance should be performed according the non-rotating plate and the cylinder tube. to the procedure indicated in the Operating There is a danger that fingers of personnel could get caught between Manual.
-
Page 10: Maintenance
9/10 3. Maintenance Caution As a jig is required for bore size ø6, do not disassemble when replacing seals etc. If overhaul is required, contact SMC Sales Office. Checks 1.Daily check 1)Whether the operation is smooth or not. 2)Changes in piston speed and cycle time. 3)Whether the stroke is appropriate or not. -
Page 11: Troubleshooting
10/10 5.Troubleshooting Description Possible causes Countermeasures Note Insufficient The piston seal is Replace the piston seal. For ø6, request SMC output worn out. to repair. ・ Increase the bore size of the Operating The load is too much for speed is too cylinder. - Page 12 Revision history 4-14-1, Sotokanda, Chiyoda-ku, Tokyo 101-0021 JAPAN Tel: + 81 3 5207 8249 Fax: +81 3 5298 5362 http://www.smcworld.com Note: Specifications are subject to change without prior notice and any obligation on the part of the manufacturer. © 2008 SMC Corporation All Rights Reserved No.
Need help?
Do you have a question about the C(D)U Series and is the answer not in the manual?
Questions and answers