Advertisement
Quick Links
A M D S A V E T H E S E I N S T R U C T I O N S
*
O W N E R ' S I N S T R U C T I O N M A N U A L
FOR
C A U T I O N
INSTRUCTIO
NS CAREFULLY FOR SAFE
PERATION. IF
UNSURE CONSULT
P r o f e s s i o n a l
Note: Approximate time of assembly is 30 min to 1 hour.
These instructions are suitable
Listed Ceiling fan.
Intertek
Advertisement
Related Manuals for Hardware House 20-7164
Summary of Contents for Hardware House 20-7164
- Page 1 A M D S A V E T H E S E I N S T R U C T I O N S O W N E R ' S I N S T R U C T I O N M A N U A L C A U T I O N INSTRUCTIO NS CAREFULLY FOR SAFE...
- Page 2 Safety Tips — — — Unpacking your fan Tools and Material Electrical Outlet box Preparing for installation M o u n t i n g Bracket Hanging System Blade Assembly M o u n t i n g Wiring Secure t o Ceiling Light Fixture Installation controller Operation and M a i n t e n a n c e - —...
- Page 3 To avoid possible electric shock, turn off the electricity at the main fuse box or circuit panel before you begin the fan installation or before servicing the fan or installing accessories. CAUTION: READ ALL INSTRUCTIONS AND SAFTY INFORMATION CAREFULLY BEFORE INSTALLING YOUR FAN AND SAVE THESE INSTRUCTIONS.
- Page 4 Unpack your fan and check the Do not discard the carton. If warranty replacement or repair is ever necessary the fan should be returned in original packaging. Remove parts and hardware. Do not lay motor housing on its side: the decorative casting may shift.
- Page 5 Phillip screw driver Blade screw driver Adjustable pliers or wrench Step Ladder Wire cutter Electrical tape 1. If there is an existing outlet box, ensure it is clearly marked"suitable for fan support". If not, it must be replaced with an approved one. 2.
- Page 6 fflhdk- Use metal outlet box suitable for fan support(must support 35lbs). Before Unpack and inspect fan carefully to be attaching fan to outlet box, ensure the certain all contents are included. outlet box is securely fastened by at least Turn off power at fuse box to avoid two points to structural ceiling member(a possible electrical shock.
- Page 7 Use the downrod supplied with fan, Place downrod assembly(l) into remove clamp pin(l) and cross pin(2) canopy(2)and yoke cover(3). Feed motor form downrod(3). wires through the downrod assembly(l). Insert downrod into downrod coupling. Make sure to align hole in downrod with the hole in downrod coupling.
- Page 8 Blade Remove the two screws Insert the blades one at a time Fix the window cover holding the "window through the around the with the t w o cover" to the top of the fan housing and secure each screws. motor housing.
- Page 9 B L A C K W H I T E W H I T E B L A C K B L U E AC POWER PAN MOTOR ANTENNA Make wiring connections from the house and the motor to the remote receiver as shown above.
-
Page 10: Installation
INSTALLATION Locate the indentations on the neck of the glass and align with the protrusions on the Install light bulbs((13 watt max, bulb not inside of the light kit. Lift the glass up included). allowing the protrusions to engage the indentations of the glass, and twist the glass clockwise to lock into place. -
Page 11: Operation And Maintenance
remote control is ready for use after battery installation remote is to use 1 x9V battery. of transmitter : Turn on ceiling fan at high speed. : Turn on ceiling fan at medium speed. : Turn on ceiling fan at low speed. : Turn off ceiling fan. - Page 12 If you have difficulty operating your ceiling fan, it may be the result of incorrect assembly, installation, or wiring. In some cases, these installation errors may be mistaken for defect. If you experience any faults, please check this Trouble Shooting Chart. If a problem cannot be remedied, please consult with your authorized electrician and do not attempt any electrical repairs yourself.
Need help?
Do you have a question about the 20-7164 and is the answer not in the manual?
Questions and answers