SEA 222 Operator's Manual page 7

(
TO ADJUST THE SQUELCH THRESHOLD:
Put the SEA 222 into PROGRAM mode (see previous section
TO
PROGRAM THE SEA 222 "SCRATCH PAD" MEMORY). Display will read
"PROGRAM", then "BIN#?".
Press: "SOL" button.
Display will read "SQ 0-9?" (4 is the factory set threshold).
Press: desired single digit between 0-9 and "ENT". ("O" is off and "9" is
maximum.)
TO EXIT THE PROGRAM MODE:
Press: "EMER" or:
If no entry is made for 10 seconds after program entry, the system will
automatically exit the Program Mode.
Display will read the last frequency programmed or "2182.0" if no
frequency was previously programmed.
Press: "CH/FR".
Display will read channel number.
TO ENTER A RECEIVE ONLY FREQUENCY:
Exit the Program mode.
Press: desired five or six digit frequency between 2000.0 and 24000.0,
then "ENT".
Example: Press "1,0,0,0,0,0" then "ENT".
The operating system will interpret this as a RECEIVE fre-
quency of 10,000.0 kHz.
The transmitter is inhibited in this mode.
TO SELECT AN EMERGENCY CHANNEL:
Press any SINGLE DIGIT, then "EMER".
Example: Press "O", "EMER".
Display will read 2182.0.
(Note: Up to 10 emergency frequencies (0-9) may be stored in scratch
pad memory.)
As already noted, CHANNEL 0 is loaded with 2182.0 kHz.
6
(
POINTS TO REMEMBER:
• It may help to read the comprehensive instructions in your SEA 222
Instruction and Maintenance Manual before attempting to operate your radio.
The information in this booklet is a shortened version of those instructions, and
assumes a certain .level of familiarity with the equipment. For your conven-
ience, keep this "how to" information and frequency listing in a handy place for
quick reference on board your vessel.
0
Let your SEA 222 warm up for at least three minutes. Transmitting
before 3 minutes may result in a violation of FCC regulations.
• Confused? If at any time during the programming process, you are
uncertain as to how to proceed, press "EMER" or just wait 10 seconds. At this
point you may re-enter the Program Mode and try again.
• Any frequency between 2000.0 kHz and 24000.0 kHz may be
selected for entry into the "scratch pad" memory. Before using them,
remember they must be legally authorized for the desired operating service.
Unauthorized use of frequencies could result in a citation by the FCC. When
the SEA 222 is to be used in services other than the marine service, it is
possible to provide a special program for the permanent memory. Contact the
factory for information regarding special programming.
SEA 222 FREQUENCY PROGRAM
CHANNEL SHIP SHIP
NUMBER TRANSMIT RECEIVE
FREQ.
201
2003· : SIMPLEX
203 .
:2ooe·
SIMPLEX
209 · . 203 f5 ; 2490 . ·
;~~~ · · ... , ~g~~· : ~:~~t~~
-
213 ·-2079;·
'SIMPLEX:
214
... 2082.5
SIMPLEX:
215 2086 . SIMPLEX
217·
2~d~·/·
.
SIMPLEX
218 2096.5 SIMPLEX
219 2115 SIMPLEX
220 2118 SIMPLEX
221 2118
2514
USE
SHIP-TO-SHIP,. GREAT LAKES
'ALASKA>' . . . . ,
··•WOM .Ft LAUDERDALE ,
BRITISH:coLUMBIA wx
SHIP~To~SHIP
/,. '
. SHIP~TO~SHIP'····
SHIP~To~SHIP
ONLY . · ..
SHIP-TO~'SHIP, MISSISSIPPI 'RIV£:Ri
• LIMITED COAST . . ·· ·· ...
.
SHIP·TO~SHIP
ONLY-COMMERCIAL FISH
SHIP-TO-SHIP
SHIP TO LIMITED COAST STATION
ALASKA
ALASKA
WOM FT. LAUDERDALE
WLC-ROGERS CITY
WFU-P, HURON
WBL-BUFFALO
7