Subscribe to Our Youtube Channel
Related Manuals for Teba TP-10
Summary of Contents for Teba TP-10
- Page 1 Installation & Manuals Pellet Stove Model TP-10 DIN EN 13240 Tested according to Tip BA 1 Please, see enclosed declaration of conformity for efficiency and emission...
-
Page 2: Table Of Contents
Contents Introduction General Information Safety Safety Distances(minimum distance) 5-6-7 Installation and Connections Electricity Chimney Connection Control Panel Buttons& Leds Display Errors Menu 4.4.1 Combustion(Working) Power Menu 4.4.2 Heating Power Menu 4.4.3 Working Thermostat Menu 4.4.4 Chrono Menu 4.4.4.1 Activation 4.4.4.2 Programming 10-11 4.4.5... -
Page 3: Introduction
Pellet stoves which is environment friendly and provide comfortable and easy-to-use interior aqueous and dry system, have taken place of dry stoves which used in Turkey and over the World. Pellet stoves is used to heat some areas like homes, work places…etc. These are heating units that combine pleasure with fireplace view, comfort with its efficiency and fuel save. -
Page 5: General Information
2.0 General Informations All required standart examinations have been made for your product. Predicted parameters associated with combustion efficiency and exhaust gas emissions are observed. The conformity of the product described in this manual was tested in IMQ Primacontrol Laboratory Pellet stoves provide comfortable and easy use through blowing hot air to ambient and fireplace view. - Page 6 80cm from radiation area In the radiation field of the flame monitor cover (C), at 80 cm distance, combustible materials and furniture should notbe placed. This distance can be reduced to 40cm when the protection panel which inhibits the passage of heat is put between stove and combustible materials.
- Page 7 BACK WALL RADIATION AREA You can order floor protection plate from seller when you require.
-
Page 8: Installation And Connections
3.0 Installation and Connection Product assembly must be installed by authorized person. Pellet stove is a full automatic device. Switch, sensor and similar parts are located inside the stove safely. 3.1. Electricity Electricity system should be 220V-230V/50Hz. Our company is not responsible for any problem which occur in case sudden low or high volt. -
Page 9: Buttons& Leds
4.1 Buttons& Leds Buttons Leds 4.2 Dısplay The main display shows; date, hours, chrono activation, combustion power, heating power, functioning state, possible error code, main temperature and main thermostat. 4.3 Errors... -
Page 10: Menu
4.4 Menu Push P2 button to enter in the User Menu Using P3 and P4 buttons it is possible to select the desired Menu or Submenu. Push P2 button to enter in desired Menu or Submenu. To decrease or increase value push the buttons P3 or P4; to save the new vale push the button P2; to cancel the modifies and restore the old parameter’s value push the button P1. -
Page 11: Clockmenu
times. The procedure to follow is this: Select the time to program with buttons P3 or P4 Enter the modality modify (the selected time blinks) with button P2 Modify the times with button P3 or P4 Save with button P2 Activate (appears “V”) or deactivate the time band (there is no “V”) pushing the button P2 Programs around midnight... -
Page 12: Pellet Manual Loadingmenu
Switch ON the Power Supply pressing at the same time one button on the Remote Control waiting about 5 seconds until an acoustic signal is emitted confirming the code learned 4.4.8 Pellet Manual Loading The procedure activates the Pellet manual loading with activation in continue modality of the Auger engine. -
Page 13: Suitable Fuel
5.1 Suitable Fuels Pellet is a solid fuel which is obtained by compressing wood wastes at high pressure after drying, grinding and making shavings and diameter of pellet 6-8 mm. Wood pellet contains approximately 7-12% moisture. Its calorie higher than wood since its moisture rate is low. -
Page 14: Cleaning And Maintenance
5.2 Cleaning And Maintenance Once a year, stove fire transition pipes are cleaned through moving out cast iron cover and cleaning cover of chimney emission fan... -
Page 15: General Warranty
6.0 General Warranty Warranty Policies TEBA THERM provide guarantees to the buyer within the framework of legal provisions. Two-year warranty periode which starts from the date of delivery, to benefit from warranty legal policies please keep your bill. Pump, glass, faults on control board because of low or high voltaj, wrong use are out of warranty.
Need help?
Do you have a question about the TP-10 and is the answer not in the manual?
Questions and answers