Status Leds; Low Battery Red Led; Battery Type Selection; Operation Status - Heart Interface 10 Owner's Manual

O P E R A O P E R A TION TION
O P E R A TION TION
O P E R A O P E R A TION
STA A A A A TUS LEDs ST ST ST ST TUS LEDs TUS LEDs TUS LEDs TUS LEDs
Each Status LED performs two functions,
providing battery type selection and operation
s t atus.

Status LEDs

Status LEDs Status LEDs Status LEDs Status LEDs
INVERT INVERT INVERT C H A R G E C H A R G E C H A R G E C H A R G E C H A R G E
INVERT INVERT
CHARGE / GEL1 CHARGE / GEL1 CHARGE / GEL1 CHARGE / GEL1 CHARGE / GEL1
INVERT / WET INVERT / WET
INVERT / WET INVERT / WET INVERT / WET
Battery T Battery T Battery T Battery T

Battery Type Selection

ype Selection ype Selection ype Selection ype Selection
After holding the INVERT button down for
5 seconds, use the CHARGE button to select
b a t t e r y t y p e :
WET GEL 1

Operation Status

Operation Status Operation Status
Operation Status Operation Status
INVERT INVERT INVERT - Green LED INVERT INVERT
The INVERT push-button switch is located on
t h e f r o n t o f t h e u n i t .
• When the LED is solid green, the unit is
in invert mode. This occurs by pressing the
INVERT switch for (3-5 seconds).
• When the LED is blinking slowly (1 time
per second), the inverter is in standby with AC
power applied and the transfer switch engaged
• Press the INVERT switch again to turn
the inverter OFF.
CHARGE CHARGE
CHARGE - Green LED CHARGE CHARGE
• The CHARGE push-button switch is lo-
cated on the fornt of the unit.
When external AC is applied to the AC in-
put of the unit, the charger automatically turns
ON. The CHARGE LED will be solid green.
• When the LED is blinking slowly, ( 1 t i m e
per second) the charger is ready, b u t e x t e r n a l
AC power is not available.
• Press the CHARGE switch again to turn
8
TSC TSC
REMOTE REMOTE REMOTE REMOTE REMOTE TSC TSC TSC
OVERTEMP OVERTEMP OVERTEMP
OVERTEMP OVERTEMP
OVERLOAD / AGM OVERLOAD / AGM OVERLOAD / AGM OVERLOAD / AGM OVERLOAD / AGM
LOW BATTERY / GEL 2 LOW BATTERY / GEL 2 LOW BATTERY / GEL 2 LOW BATTERY / GEL 2 LOW BATTERY / GEL 2
GEL 2 AGM
the charger OFF. The charger defaults to ON
when operation without a remote or with the
Freedom Remote Control Panel.
• When the LED is OFF, the charger has
been manually turned OFF. This can only be
accomplished while AC power is being
supplied.
NOTE: When AC power is available, the
default setting for the charger is ON. If the unit
was manually turned OFF and AC power is in-
terrupted and becomes available again, the
charger will return to ON.
LOW BA LOW BA TTER TTERY Y Y Y Y - Red LED TTER
LOW BA LOW BATTER LOW BA TTER
• • • • • When the LED is OFF the battery
voltage is normal, between 10.5 and 15.0
volts DC.
• When the LED is solid red, it indicates a
battery warning condition, the battery voltage is
below 10.5 volts DC or above 15.0 volts DC.
• When the LED is blinking slowly, ( 1 t i m e
per second), a battery shutdown has occurred.
The voltage is either below 10.0 volts DC or
above 15.5 volts DC.
• When the LED is blinking rapidly (5
times per second), a potential problem in the
DC system has been detected. Check your
batteries, battery cables and DC loads.
OVERTEMP/OVERLOAD OVERTEMP/OVERLOAD - Red LED OVERTEMP/OVERLOAD
OVERTEMP/OVERLOAD OVERTEMP/OVERLOAD
• • • • • When the LED is Off operation is
normal.
• When the LED is red, there is an over
temp or overload condition. Check for
excessive loads or short circuit on the output
o f t h e i n v e r t e r. Correct the condition and restart
by pushing the INVERT switch.
Part No. 90-0123-00
Libertycombi.p65 11/05/99