Advertisement
8.0 - PROGRAMMING
Only expert users should modify these settings to avoid malfunctions of the parking
!
The unit display (front and rear) will show one of the following indications:
FS: Factory Setting, standard adjustment , "Factory parameters".
CS: Custom Setting, user-chosen adjustment, "Custom Parameters".
To activate the programming procedure proceed as follows:
Press one of the two push-buttons on the control unit and keep it pressed for at least two seconds;
the system will activate and enter in the programming mode.
Press the left push-button to go to the previous
parameter.
When the parameter you want to modify is displayed, press one of the push-buttons and keep it
pressed until the display starts to blink; at this point you can modify the parameter.
Press the left push-button to decrease the
value of the parameter.
Press one of the two
push-buttons
on the control unit and keep it pressed for at least two seconds
to register the value.
The display will stop blinking and the selected parameter will be displayed.
If no button is pressed within10 seconds, the system will exit the programming mode.
Press the two push-buttons on the control unit and keep them pressed for more than
!
two seconds to reset all the factory settings (FS).
PAGE 10 - INSTALLER MANUAL
system.
Press the right push-button to go to the next
parameter.
Press the right push-button to increase the
value of the parameter.
9.0 - SETTING OF PARAMETERS
9.1 - FRONT UNIT (MAIN UNIT)
Nr.
PARAMETERS
01
Volume of buzzer
02
Detection range of front central sensors
03
Detection range of front corner sensors
04
Detection range of rear central sensors
05
Detection range of rear corner sensors
06
STOP zone of front central sensors
07
STOP zone of front corner sensors
08
STOP zone of rear central sensors
09
STOP zone of rear corner sensors
11
Number of speed signal pulses
12
Delay of front sensors deactivation
13
Delay of rear sensors activation
Service display front unit (main unit), system
15
testing
16
Front sensors detection
Sensitivity of front sensors to detect
17
obstacles
Ref.1
: not activated, 1 low, 2 high.
Ref.2
: the display having only 2 numbers, the range will be indicated as 20 and 80 instead of 120 and
180.
Ref.3
: by setting "00", the system is activated every time ignition is turned on; to deactivate, press the
push-button with the LED. Press again, to reengage the sensors.
Ref.4
: if your vehicle has an automatic transmission, select " 1".
Ref.5
: 0 not activated, 1 shows ldistance from the closest front obstacle, 2 shows distance from the
closest rear obstacle (insert reverse gear), 3 shows vehicle speed (in km/h, for programming
refer to parameter 11).
Ref.6
: 0
only if the car or obstacle is moving, 1 even if the vehicle or obstacle is not moving
Ref.7
: 1 low, 2 standard, 3 high.
Nr.
PARAMETERS
10
Suppression of spare wheel indication
Sensitivity of rear sensors to detect
17
obstacles
Rif.1
: i
ncrease the value (setting can be modified from 0= deactivated, to 3) until the system no longer
detects the external spare wheel or the tow hitch
Rif.2
: 1 low, 2 standard, 3 high.
RANGE
0, 1, 2 (
Ref.1
)
From 50 to 95 cm
From 50 to 95 cm
From 120 to 180 cm (
Ref.2
)
From 50 to 95 cm
From 35 to 50 cm
From 35 to 50 cm
From 35 to 70 cm
From 35 to 70 cm
Da 1 to 99
0 or from 10 to 60 sec. (
Ref.3
)
0, 1 (
Ref.4
)
0, 1, 2, 3 (
Ref.5
)
0,1 (
Ref.6
)
1, 2, 3 (
Ref.7
)
9.1 - REAR UNIT
RANGE
0, 1, 2, 3 (
Ref.1
)
1, 2, 3 (
Ref.2
)
INSTALLER MANUAL - PAGE 11
SETTING
2
80
55
160
55
35
35
35
35
3
00
0
0
0
2
.
SETTING
0
2
Advertisement
