Related Manuals for Landis GPDUAL
Summary of Contents for Landis GPDUAL
- Page 1 WORKMASTER 1000 (SKU: GPDUAL & GP220) ORTHO SANDER Operator Manual Manufactured by 04/2018...
- Page 2 Operator Manual - GRIND PRO DUAL INTRODUCTION The Landis Grind Pro Dual Sander is a compact, durable machine designed for fast, complete finishing work. It will deliver efficient, dependable service when used correctly and with care. As with any piece of specialized equipment, for best performance the manufacturer’s instructions must be followed.
-
Page 3: Installation
COULD CAUSE EYE INJURY. INSTALLATION The Landis Sander should be located on a flat, firm surface, in an area free of obstructions that could interfere with the safe operation of the equipment. The Sander should be positioned and leveled with the 4 white plastic legs to obtain quiet operation with a minimum of vibration. -
Page 4: Lockout Procedures
In a multiple lockout/tagout situation, it will also identify any worker(s) who may not have finished working. Locks and tags must be durable enough to withstand the environment in which they are to Landis International - 4... - Page 5 Ensure workers are a safe distance from any potential hazard. The lock and tag should be removed from each energy-isolating device by the worker who applied the lock and tag. Notify affected workers that locks and tags have been removed. Landis International - 5...
- Page 6 Switch Button Before shipment, your Landis Sander was checked at the factory for proper adjustment and operation. However, due to the possibility of jarring or damage during handling and shipping, it is necessary to check that the machine is in proper working order before use.
-
Page 7: Sandpaper Replacement
INJURY TO THE OPERATOR AND OTHERS IN THE WORK AREA. • THESE QUICK CHANGE ACCESSORIES SHOULD BE PROPERLY ENGAGED ON THE SHAFT TO ENSURE SAFE OPERATION. MAKE SURE PIN ON SHAFT ENGAGES THE ADAPTOR CORRECTLY. LEFT BAYONET RIGHT BAYONET CORRECTLY INSTALLED CORRECTLY INSTALLED Landis International - 7... - Page 8 Operator Manual - GRIND PRO DUAL FOR WORKMASTER 1000 (SKU: GPDUAL): • It is not necessay to remove the bayonet to slide the new sand paper on the rubber wheel. • Slide and turn down the sandpaper to remove it. It is easier to put a new sandpaper on the rubber wheel if you remove it from de bayonet.
- Page 9 SAND PAPER REPLACEMENT The sand paper can be obtained in various grit to suit your needs and are easily changed. • Sandpaper 80 grit, SKU: PN80 • Sandpaper 100 grit, SKU: P100 • Sandpaper 120 grit, SKU: PN120 Landis International - 9...
- Page 10 Failure to shake the dust bag daily will not only increase this likelihood, but will also cause a significant loss of dust extraction from the sanding areas. Maintenance is important, ✓ see our recommendations page 12. Landis International - 10...
- Page 11 • FAILURE TO PROPERLY MOUNT THE ADAPTOR WILL RESULT IN FLYING APART AND POSSIBLE INJURY TO THE OPERATOR AND OTHERS IN THE WORK AREA. • THESE QUICK CHANGE ACCESSORIES SHOULD BE PROPERLY ENGAGED ON THE SHAFT TO ENSURE SAFE OPERATION. MAKE SURE PIN ON SHAFT ENGAGES THE ADAPTOR CORRECTLY. Landis International - 11...
-
Page 12: Maintenance
WORK AREA WHEN SERVICING THE MACHINE EYE PROTECTION IS REQUIRED FOR PROTECTION FROM FLYING DEBRIS AND DUST, WHICH COULD CAUSE EYE INJURY. DAILY AND WEEKLY MAINTENANCE Clean your Landis Sander daily. Shake dust bag daily. Empty it weekly. (Optional dust collector system) After cleaning the machine, turn dust extraction motor off. -
Page 13: Monthly Maintenance
V-Belt – Check tension and adjust if necessary. V-BELT ADJUSTMENT AND REMOVAL The V-Belt on the Landis Sander should be checked monthly for proper tension and general condition. Loose V-Belt will decrease the power available to the various tools and lower the efficiency of your Sander. -
Page 14: Motor Replacement
Operator Manual - GRIND PRO DUAL LUBRICATION Your Landis Sander is equipped with sealed bearings throughout, which should be replaced if they ever wear out. Other parts should not require any lubrication, only cleaning the parts is required. Lubrication will only attract dust and would be more harmful than helpful. -
Page 15: Troubleshooting
MOTOR STOPS WITH SWITCH ON CAUTION! TURN SWITCH OFF IMMEDIATELY 1. Too much equipment operated on same circuit on which Landis machine is connected. Check circuit breaker or fuse box. Refer to the lockout procedures before the next step (page 4).