Download
Share
Print this page
  1. Manuals
  2. Brands
  3. AUREL Manuals
  4. Motherboard
  5. DEMO XTR-8LR100
  6. User manual

AUREL DEMO XTR-8LR100 User Manual

Hide thumbs

Advertisement

Quick Links

Download this manual
DEMO XTR-8LR100
DEMO XTR-8LR10
User Manual
Picture 1: Demo board XTR-8LR100
Picture 2: Demo board XTR-8LR10
DEMO-BOARD XTR-8LR100 (Picture 1) e DEMO-BOARD XTR-8LR10 (Picture 2) is an evaluation board
of the transceiver module XTR-8LR100 and module XTR-8LR10 which can easily check functionality,
power consumption, commands and performance of radio link. The difference between the two demo board
is on the mounted module, XTR-8LR100 that have mode of operation, Normal, Rx ciclyc, Tx ADC value
and XTR-8LR10 that is implemented the Normal mode operation.
For more detail about the operation mode refer to the user manual of the used module.
The device is able to work with external power supply or powered by four AA batteries, for tests in stand-
alone. It is included a stylus antenna operating on the 868 MHz band connected to the SMA connector,
thereby using the test mode through some diagnostic led, it is possible to realize radio links.
The DEMO-BOARD is equipped with a USB connector with COM port emulation realized with CI
FTDI1235-C and an SMA input connector radio output for the RF connections measurement instruments.
The following table shows in detail the various elements included in the board, through commented image.
Le caratteristiche tecniche possono subire variazioni senza preavviso. AUR°EL S.p.A. non si assume la responsabilità di danni causati dall'uso improprio del dispositivo.
AUR°EL S.p.A. Via Foro dei Tigli, 4 - 47015 Modigliana (FC) – ITALY
Rev 2.2 17/05/2016
Tel.: +39.0546.941124 Fax: +39.0546.941660
Page 1 of 17
http://www.aurelwireless.com
- email:
rfcomm@aurel.it

Advertisement

loading
Need help?

Need help?

Do you have a question about the DEMO XTR-8LR100 and is the answer not in the manual?

Questions and answers

Related Manuals for AUREL DEMO XTR-8LR100

Summary of Contents for AUREL DEMO XTR-8LR100

  • Page 1 DEMO XTR-8LR100 DEMO XTR-8LR10 User Manual Picture 1: Demo board XTR-8LR100 Picture 2: Demo board XTR-8LR10 DEMO-BOARD XTR-8LR100 (Picture 1) e DEMO-BOARD XTR-8LR10 (Picture 2) is an evaluation board of the transceiver module XTR-8LR100 and module XTR-8LR10 which can easily check functionality, power consumption, commands and performance of radio link.
  • Page 2 DEMO XTR-8LR100 DEMO XTR-8LR10 User Manual Picture 3: Description top side of demo XTR-8LR100/XTR-8LR10 External Supply 8÷12Vdc Plug input male general supply 8÷12Vdc 300mA General switch power board. Power Switch ON= board switched on OFF= board switched off Power Supply Led Red led power indicator.
  • Page 3 DEMO XTR-8LR100 DEMO XTR-8LR10 User Manual Led 1 green used in the TEST mode LED RX or TX “PONG” On when it sends or receives the message "PONG", or in the other modes it indicates the transmission status LED RX or TX “PING”...
  • Page 4 To start using the DEMO XTR-8LR100/8LR10 follow the steps below: Insert the 4 AA batteries as shown in Picture 4. Power supply DEMO XTR-8LR100/8LR10 placing the Power Switch in ON position and be sure the 3 jumpers Set_A, SET_B and SET_C are open.
  • Page 5 9600bps, a START bit, 8 data bits and STOP bits, no parity. In this case, select the menu item "Port 26", used in this example as associated port to DEMO XTR-8LR100. After each change of the working parameters of the serial port, remember to click the "Change" button to Realterm, the set values are visible at any time in the small square at the bottom right of the screen Realterm.
  • Page 6 DEMO XTR-8LR100 DEMO XTR-8LR10 User Manual Click on the menu Send and select CR and LF, press the "Reset Button" of DEMO XTR- 8LR100/8LR10, then type on the empty field “++++” and then press button "Send ASCII". If communication is successful you will receive in response the following screen: By now, you can send AT commands to the demo-board.
  • Page 7 DEMO XTR-8LR100 DEMO XTR-8LR10 User Manual Change the desired parameters, type the command ATCC to get out of the command mode, or ATWR to save the new parameters on Eprom and exit from command mode, as confirming the demo-board answer with OK EXIT (see below).
  • Page 8 DEMO XTR-8LR10 User Manual The application consists in a set up of radio connection between a pair of DEMO XTR-8LR100/8LR10 respectively called Master and Slave, the first transmits autonomously the message "PING", the second receives the packet answering with the message "PONG".
  • Page 9 Using Realterm set communication speed to 115,2kbps, a START bit, 8 data bits, a bit of STOP, no parity. Select from the menu “Port 57”, used in this example as associated port to DEMO XTR-8LR100, then press the "Open" button.
  • Page 10 DEMO XTR-8LR100 DEMO XTR-8LR10 User Manual Where it is required a connection point multi-point with exclusive connection between two units or one unit and n units, it is possible to activate the NORMAL mode with addressing. You should operate as follows: NORMAL mode with addressing: The setting as described below also apply to the DEMO XTR-8LR10.
  • Page 11 DEMO XTR-8LR100 DEMO XTR-8LR10 User Manual In the following screens of Realterm, the transmission of unit 1 to 2 is displayed, of the string "Demo-board unit1 XTR-8LR100", the hexadecimal characters (0x0001) of the sender address are not displayed by Realterm for incompatibility of contemporary display to ASCI characters and HEX (screen on the right).
  • Page 12 User Manual Transmission mode ADC cyclical (Available only for DEMO XTR-8LR100): The following application realized with the DEMO XTR-8LR100 allows to transmit the value of three analog inputs: AN0 (pin4), AN1 (pin 5) and AN3 (pin6) of XTR-8LR100 module, independently and through programmed cycles.
  • Page 13 DEMO XTR-8LR100 DEMO XTR-8LR10 User Manual Command from Answer from Description PC → DEMO XTR- DEMO XTR-8LR100 → 8LR100 ++++ COMMAND-MODE Command mode enter ATS10=1 It activates network mode ATS30=1 Set the time of cyclic transmission of the status of ADC to 1sec...
  • Page 14 DEMO XTR-8LR100 DEMO XTR-8LR10 User Manual The visualization is in hexadecimal, each line contains the data of a transmission cycle. From the first line from left to right "00 01" represents source address (2 bytes in hex), "0C 22" is the value (hex) of input ADC_0 (in our application connected to + 3.3V), "00 05 "is the value (hex) of input ADC_1...
  • Page 15 Below it is shown an example realized with two DEMO XTR-8LR100 respectively in RX and TX cyclic, with switching off cycle of 5 seconds, in network mode with address (source address) of the receiver "1" and the transmitter "2";...
  • Page 16 DEMO XTR-8LR10 User Manual From sleep mode unit 2, send the following commands: Command from Answer from Description PC → DEMO XTR- DEMO XTR-8LR100 → 8LR100 ++++ COMMAND-MODE Input in Command mode ATS20=5000 Set the cyclic restart time of the...
  • Page 17 DEMO XTR-8LR100 DEMO XTR-8LR10 User Manual Errata: Release date Revision Firmware Changements from the previous revision user manual correspondent 0100 First release 18/06/2015 0110 Insert TEST, NORMAL, NORMAL mode with addressing, TX ADC cyclic. 24/09/2015 0110 Modifiche foto demo, inserimento demo XTR-8LR10...

This manual is also suitable for:

Demo xtr-8lr10