Box Contents: 1 x 4.3” Monitor 1 x Wireless Camera 1 x Suction Cup Mount 1 x Cigarette Lighter Power Adaptor Product Diagram: Menu / Press to show the menu or return to the previous menu Return Press to select up in the menu Press to turn the unit on/off when the menu is not displayed or Power / to enter within the menu...
Installation: Monitor: Positioning The Monitor: 1. Place the 4.3” monitor in the included bracket securely. 2. Connect the monitor bracket to the suction cup mount. 3. Position the suction cup on your windscreen or dash and make sure that it doesn’t obstruct your view while driving.
Camera: Positioning The Camera: 1. Place the wireless camera on the license plate or rear of the vehicle using screws or the 3M tape to securely fix in place. 2. Depending on where your camera is positioned; adjust the tilt accordingly to obtain the best view.
Page 5
2. Press the POWER / ENTER button to enter the pairing menu. 3. The pairing now should begin automatically as shown below: 4. After the pairing is successful, you should see “Paired” displayed as shown below:...
Page 6
5. Press the MENU / RETURN button to exit to the main menu. Please Note: If the pairing is unsuccessful, please repeat the procedure again. If connecting with one of two cameras; they can be both paired simultaneously or individually. Setup: Display: Select between displaying camera 1, camera 2 or displaying both cameras if you have an additional...
Page 7
5. Select which display you would like to choose between camera 1, camera 2 and split display. 6. Press the POWER / ENTER button to confirm. 7. Press the MENU / RETURN button to exit to the main menu. 8. You can press the UP button to enter the auto display when there is no menu shown. 9.
Page 8
3. Press the DOWN button; then press the POWER / ENTER button to enter the mirror menu. 4. Select which mirror mode you would like to choose depending on how your monitor is positioned on your wind screen. 5. Press the DOWN button; then the POWER / ENTER button to confirm which option you prefer. 6.
Page 9
Select the version menu to clear the paired devices so you may re-pair them again such as if you find an intermittent fault. 1. Press the MENU button to enter the main menu. 2. Press the DOWN button to select the setup menu. 3.
Page 10
6. Once viewing the version information, press and hold the UP button for 5 seconds. 7. Once this has been done, it will have cleared the channels. 8. Press the MENU / RETURN button to exit to the main menu. Picture: This option allows you to change the brightness, contrast and colour for the camera display.
Page 11
1. Press the DOWN button; then press the POWER / ENTER button to select the brightness menu. 2. Press the UP or DOWN buttons to either increase or decrease the brightness settings, then press the POWER / ENTER button to confirm the adjusted brightness. 3.
Page 12
1. Press the DOWN button; then press the POWER / ENTER button to select the contrast menu. 2. Press the UP or DOWN buttons to either increase or decrease the contrast settings, then press the POWER / ENTER button to confirm the adjusted contrast. 3.
1. Press the DOWN button; then press the POWER / ENTER button to select the colour menu. 2. Press the UP or DOWN buttons to either increase or decrease the colour settings, then press the POWER / ENTER button to confirm the adjusted colour. 3.
Problem Solution Check the monitor cigarette power socket is Monitor Won't Turn On connected Check if the cigarette socket of your vehicle is 8-30VDC Check the fuse of your cigarette light power adaptor Monitor & Camera Not Check to see if the camera is connected to 8-30VDC power Pairing Check the polarity (positive &...
Page 15
Monitor: Frequency: 2.4GHz Digital LCD: 4.3” Resolution: 480 x 272 Range: Up to 100m Antenna: 3dBi Voltage Input: 8-30VDC Standby Current: Up to 200mA Current Consumption: Up to 250mA Suitable Temperature: -10° - 50°C Dimensions: 140(L) x 87(W) x 21(H)mm Camera: Frequency: 2.4GHz Digital Resolution: 720 x 480...
Page 16
Distributed by: TechBrands by Electus Distribution Pty. Ltd. 320 Victoria Rd, Rydalmere NSW 2116 Australia Ph: 1300 738 555 Int’l: +61 2 8832 3200 Fax: 1300 738 500 www.techbrands.com...
Need help?
Do you have a question about the QM-3856 and is the answer not in the manual?
Questions and answers